PDFï¼7.7MB

More documents

Recommendations

Info

TPO / EPO07 Standard cutting conditions Work material Low carbon steels (C15E etc.) High carbon steels and Alloyed steels (C45, C55 etc.) Tool Steel (X153CrMoV12 etc.) Stainless steel (X5CrNi18-9 etc.) Grey cast iron (GG25, GG30 etc.) Ductile cast iron (GGG45 etc.) Aluminium alloys (Si < 13%) Aluminium alloys (Si 13%) Titanium alloys (Ti-6Al-4V etc.) Heat resistant alloys (Inconel718 etc.) Brinell Cutting Speed Feed per tooth: fz (mm/t) hardness Grades HB Vc (m/min) MJ HJ AJ ~ 200 AH725 90 - 200 0.05 - 0.1 0.4 - 0.9 - 200 ~ 300 AH725 90 - 150 0.05 - 0.1 0.4 - 0.9 - 150 ~ 300 AH725 80 - 120 0.05 - 0.1 0.4 - 0.9 - - AH140 90 - 150 0.05 - 0.1 0.4 - 0.9 - 150 ~ 250 AH725 100 - 180 0.05 - 0.1 0.4 - 0.9 - 150 ~ 250 AH725 80 - 150 0.05 - 0.1 0.4 - 0.9 - - KS15F 300 - 1000 - - 0.08 - 0.2 - KS15F 100 - 200 - - 0.08 - 0.2 - AH725 20 - 50 0.05 - 0.1 0.4 - 0.9 - - AH725 20 - 35 0.05 - 0.08 0.2 - 0.6 - Cautionary points when using HJ inserts HJ type inserts are designed for high feed machining. Please note the following when using HJ inserts: 1. The peripheral shape of HJ insert differs from that of other inserts (MJ, AJ). However the same insert pocket can be used. 2. When using HJ inserts, all the inserts on the cutter body must be HJ type. Do not use other types of inserts (MJ and AJ types) with HJ inserts on the same cutter body. 3. When using CAD/CAM, program it as a radius cutter. The table below shows the corner R in programming and the uncut area (t). 4. With HJ inserts, the tool diameter is equal to the diameters shown on p. 9-80 øDc + 0.6 mm r R0.8 mm w tool diameter: p. 9-80 øDc + 0.6 mm Max. ap: 0.8 mm 10° R t Amount left as uncut Corner R when programming Depth of cut:ap (mm) TungRec 07 type HJ inserts Standard conditions 1.0 0.8 0.6 0.4 0.2 0 0.2 0.4 0.6 0.8 1.0 Max. depth of cut max ap (mm) Superalloys 0.8 3.0 Feed per tooth: fz (mm/t) Main cutting edge length W (mm) Steel Cast Iron Amount left as uncut t (mm) Stainless Corner R when programming 0.4 R 0.5 0.3 R 1.0 9 TAC Mills 9–59
TPS / EPS11 Diameter ø12~63 mm Steel Stainless Cast Iron Non-ferrous Shoulder Milling R R R Radius Milling Slotting Slotting Side Milling Pocketing Ramping Plunging Enlarging Hole For high speed milling of steels, stainless, and superalloys øDb Rake angle: TPS11: A.R. +15.5º ~ +18º R.R. -8º ~ -6.5º EPS11: A.R. +9º ~ +17.5º R.R. -20º ~ -7º TPS ød a b Cylindrical Lf øDc øDs R ap ˚ ap Lf L Rs EPS øDc Fig. A ˚ Max. ap: 10.6 mm Fig. B TPS11 (Fig. A: bore type) No. of Dimensions (mm) Weight Clamping Cat. No. Stock Air hole Center bolt Inserts øDc øDb ød r Lf b a (kg) screw Inserts TPS11040RB-E 6 40 35 16 19 40 5.6 8.4 0.2 without CM8X30 TPS11050RB-E 7 50 41 22 20 40 6.3 10.4 0.4 without CSPB-2.5 ASMT11T3... CM10X30 ASGT11T3... TPS11063RB-E 8 63 41 22 20 45 6.3 10.4 0.6 without Mounting details 9-138A 9 TAC Mills EPS11 Type Close pitch Coarse pitch (Fig. B: shank type) Cat. No. Stock No. of Dimensions (mm) Weight Clamping Inserts Air hole ØDc ØDs rs Lf L (kg) Screw EPS11012RS 1 12 0.1 with EPS11016RS 2 16 16 60 25 85 0.1 with EPS11018RS 2 18 0.1 with CSPB-2.5S EPS11020RS 2 20 0.2 with 20 70 30 100 EPS11021RS 2 21 0.2 with EPS11025RS 3 25 0.4 with EPS11026RS 3 26 25 35 115 0.4 with EPS11030RS 3 30 0.4 with EPS11032RS 3 32 80 0.7 with CSPB-2.5 EPS11033RS 3 33 0.7 with 32 40 120 EPS11040RS 4 40 0.8 with EPS11050RS 5 50 1.0 with EPS11020RSB 3 20 0.2 with 20 70 30 100 EPS11021RSB 3 21 0.2 with CSPB-2.5S EPS11025RSB 4 25 0.4 with EPS11026RSB 4 26 25 80 35 115 0.4 with EPS11030RSB 4 30 0.4 with EPS11032RSB 5 32 0.7 with CSPB-2.5 EPS11033RSB 5 33 0.7 with 32 80 40 120 EPS11040RSB 6 40 0.8 with EPS11050RSB 7 50 1.0 with Inserts ASMT11T3... ASGT11T3... The next page is followed. : Stocked items. 9–60 Technical Reference (15-1)
Page 1 and 2:
R Lf ap 6.4mm Chapter Composition o
Page 3 and 4:
Designation System for TAC Mills TA
Page 5 and 6:
Designation System for TAC Milling
Page 7 and 8:
Selection Guide for TAC mills Face
Page 9 and 10: Selection Guide for TAC mills Face
Page 11 and 12: Selection Guide for TAC mills Face
Page 13 and 14: Selection Guide for TAC mills Squar
Page 15 and 16: Selection Guide for TAC mills Squar
Page 17 and 18: Selection Guide for TAC mills Selec
Page 19 and 20: TUNGALOY Selection 9 TAC Mills Char
Page 21 and 22: Basic Selection for TAC Mills Face
Page 23 and 24: Basic Selection for TAC Mills Face
Page 25 and 26: Basic Selection for TAC Mills Shoul
Page 27 and 28: Basic Selection for TAC Mills Shoul
Page 29 and 30: Basic Selection for TAC Mills High
Page 31 and 32: Basic Selection for TAC Mills Die E
Page 33 and 34: TAC Mill Overview Bore types Face M
Page 35 and 36: TAC Mill Overview Bore types Should
Page 37 and 38: TAC Mill Overview Shank types Face
Page 39 and 40: TAC Mill Overview Shank types High
Page 41 and 42: TEN / EEN type Diameter ø32 ~ 160
Page 43 and 44: TAN type Diameter ø63 ~ 315 mm 45
Page 45 and 46: T/EAW13 Diameter ø50 ~ 160 mm 45°
Page 47 and 48: T/EAW13 9 TAC Mills Standard cuttin
Page 49 and 50: Lightning Mills TME4400 /B Face Mil
Page 51 and 52: 15˚ 15˚ TAC Mills for large depth
Page 53 and 54: TAC Mills TGP4100RBAE Standard cutt
Page 55 and 56: All PCD-tipped TAC Mills for high f
Page 57 and 58: TPQ / EPQ type JIS Diameter ø25 ~
Page 59: TPO / EPO07 Diameter ø12 ~ 50mm St
Page 63 and 64: TPS / EPS11 Replacement Parts TPS /
Page 65 and 66: TPO / EPO18 Diameter ø25~160 mm St
Page 67 and 68: Machining modes Shoulder milling Sl
Page 69 and 70: TPM / EPM type Roughing type øDb
Page 71 and 72: TPD / EPD type Diameter ø12 ~ 40 m
Page 73 and 74: 1.4 1.4 TPW13 Diameter ø50 ~ 125 m
Page 75 and 76: 9 TAC Mills EPH Shoulder Milling Ca
Page 77 and 78: EPH Standard cutting conditions Sh
Page 79 and 80: EVH Diameter ø10 ~ 16 mm 90° ~ 4.
Page 81 and 82: All PCD-tipped TAC Mills for high f
Page 83 and 84: TAC Mills for large depth of cut TP
Page 85 and 86: TAC Mills TSE3000R(IA)E Face Millin
Page 87 and 88: TAC Mills TSE4000RIAE Face Milling
Page 89 and 90: Top-Feed Mills, AD TPS/EPS17 Should
Page 91 and 92: Top-Feed Mills, AD TPS/EPS17 Machin
Page 93 and 94: 15°17° 1 mm ø16 ~ 80 mm Air Hole
Page 95 and 96: Standard cutting conditions Work ma
Page 97 and 98: Standard cutting conditions Work ma
Page 99 and 100: TXQ12R ø50~125 mm 2 mm Steel Stain
Page 101 and 102: EXH Diameter ø10 ~ 16 mm 20° 0.6,
Page 103 and 104: T/EXP Diameter ø20 ~ 125 mm 10°,
Page 105 and 106: T/EXP Inserts 05 type General inser
Page 107 and 108: T/EXP Diameter ø20 ~ 160 mm 10°,
Page 109 and 110: TRC / ERC type Inserts For general
Page 111 and 112:
TAC Flash radius mills TRD12 • 16
Page 113 and 114:
TAC radius mills T/ERF6000 Diameter
Page 115 and 116:
TAC Flash endmills with center cutt
Page 117 and 118:
TAC Flash Endmills ESD10 Shoulder M
Page 119 and 120:
TAC Flash ball endmills EBP R Radiu
Page 121 and 122:
TAC ball Endmills TBN1000 Pocketing
Page 123 and 124:
TAC Flash Mills for plunging TZP12
Page 125 and 126:
TAC Flash Mills for plunging TZF11
Page 127 and 128:
“T-Bar” Modular System TMS Diam
Page 129 and 130:
TAC Flasah chamfering mills ECC31 G
Page 131 and 132:
TAC Mills for super finishing SFP40
Page 133 and 134:
All PCBN-tipped TAC Mills for high
Page 135 and 136:
ASN / TSN ø100 ~ 250 mm Steel Stai
Page 137 and 138:
ASN / TSN Replacement parts Work ma
Page 139 and 140:
Mounting Details for TAC Mills Cutt
Page 141 and 142:
TAC Milling Inserts Inserts ADMT08P
Page 143 and 144:
TAC Milling Inserts AST11T3PDR-MJ/M
Page 145 and 146:
TAC Milling Inserts LMEUZNEN-MJ Sha
Page 147 and 148:
TAC Milling Inserts ONUAN-ML/MJ/W S
Page 149 and 150:
TAC Milling Inserts SCMT08-23 Shape
Page 151 and 152:
TAC Milling Inserts SEN1203AG, SEKR
Page 153 and 154:
TAC Milling Inserts SPHA431FNW, SPH
Page 155 and 156:
TAC Milling Inserts SW13T3AFR- Shap
Page 157 and 158:
TAC Milling Inserts TEN43Z, TECN43Z
Page 159 and 160:
TAC Milling Inserts XCET310404ER St
Page 161 and 162:
TAC Milling Inserts XVGTEC-MJ, XVG
Page 163 and 164:
TAC Milling Inserts ZDAT/FN Shape C
show all

PDFï¼7.7MB

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

PDFï¼7.7MB