PK-232 MBX Operating Manual - N3UJJ

More documents

Recommendations

Info

_______________________________________________________________________________ CRAdd ON|OFF Default: OFF Mode: Baudot RTTY Host: CR _________________________________ Parameters: _________________________________ ON - Send in Baudot RTTY. OFF - Send in Baudot RTTY (default). _______________________________________________________________________________ The CRADD command permits you to set the PK-232's "newline" sequence so that an additional carriage return is ADDed automatically at the end of each typed line. When CRADD is ON the line-end sequence is . When CRADD is OFF the line-end sequence is . The double carriage return is required in some RTTY services such as MARS. CRADD has no effect on received data. _______________________________________________________________________________ CStatus [Short] Immediate Command Mode: Packet Host: Not Supported _______________________________________________________________________________ CSTATUS is an immediate command helpful in multiple connections. When CSTATUS is typed, your monitor displays Link State of all ten logical channels as well as the current input/output channel as follows: NOT CONNECTED TO ANY STATION CONNECTED TO TWO STATIONS cmd:cs cmd:cs Ch. 0 - IO DISCONNECTED Ch. 0 - IO CONNECTED to WX1AAA Ch. 1 - DISCONNECTED Ch. 1 - CONNECTED to WX1BBB Ch. 2 - DISCONNECTED Ch. 2 - DISCONNECTED Ch. 3 - DISCONNECTED Ch. 3 - DISCONNECTED Ch. 4 - DISCONNECTED Ch. 4 - DISCONNECTED Ch. 5 - DISCONNECTED Ch. 5 - DISCONNECTED Ch. 6 - DISCONNECTED Ch. 6 - DISCONNECTED Ch. 7 - DISCONNECTED Ch. 7 - DISCONNECTED Ch. 8 - DISCONNECTED Ch. 8 - DISCONNECTED Ch. 9 - DISCONNECTED Ch. 9 - DISCONNECTED CSTATUS will give a short display if desired. CSTATUS SHORT (or CS S) displays only the current input/output channel or those channels which are connected. _______________________________________________________________________________ CText text Default: empty Mode: Packet Host: CT _________________________________ Parameters: _________________________________ text - Any combination of characters up to a maximum of 120 characters. _______________________________________________________________________________ CTEXT is the "automatic answer" text sent when CMSG is ON. The message is sent only when another station connects to you. A typical CTEXT message might be: "I'm not available right now. Please leave a message on my MailDrop." Clear CTEXT with "%", "&", "NO", "NONE" or "OFF", or simply set CMSG OFF. 8/91 A-31 From The N3UJJ.COM Document Library
_______________________________________________________________________________ CUstom "n" Default: $0A15 Mode: All Host: Cu _________________________________ Parameters: _________________________________ "n" - 0 to $FFFF (0 to 65,535 decimal) specifies a four digit hexadecimal value, where each bit controls a different function described below. _______________________________________________________________________________ The CUSTOM command was originally introduced to allow specialized features for "Custom" applications to be added to the PK-232 without burdening all users with a plethora of commands. As the CUSTOM command is quickly filling up, the command UBIT has been added to replace CUSTOM allow for more features. The CUSTOM command is retained for compatibility, but we recommend using the UBIT command as it is more flexible and easier to use. For those applications that can not take advantage of the UBIT command, the following CUSTOM features are available in this release of the PK-232 MBX. Bit 0, position $0001: Bit 1, position $0002: Bit 2, position $0004: Bit 3, position $0008: Bit 4, position $0010: Bit 5, position $0020: Bit 6, position $0040: If bit 0 is set to 1 (default), the PK-232 will discard a received packet if the signal is too weak to light the DCD LED. If set to 0, packets will be received regardless of the Threshold control setting. If bit 1 is set to 0 (default), then setting the MONITOR command to either ON or YES will result in a MONITOR value of 4. If bit 1 is set to 1, then MONITOR ON or YES will force the MONITOR value to 6. If bit 2 is set to 1 (default), a break on the RS-232 line will put the PK-232 into the Command mode (except from Host Mode). If set to 0, a break on the RS-232 line will not affect the PK-232. If bit 3 is set to 0 (default), packet channel numbers will be numbered from 0-9. If bit 3 is set to one, then packet channel numbers are labeled A-J or a-j. This bit affects only Baudot transmit. If bit 4 is set to 1 (default), the PK-232 inserts the FIGS character after a space, just prior to sending any figures, . This permits any receiving station to correctly decode groups of figures regardless of the USOS setting. If bit 4 is set to 0, the PK-232 will NOT insert FIGS characters after each space. MARS operators may want to set this bit to 0 for literal operation. If bit 5 is set to 0, (default) the PK-232 will always power up in the Command mode. If bit 5 is set to 1, then the PK-232 will remain in the previous mode, i.e., converse, command, or transparent Mode. If bit 6 is set to 0, (default), then monitoring is disabled in the Transparent mode. If bit 6 is set to 1, then monitoring is active in the transparent mode. MFROM, MTO, MRPT, MONITOR, MCON, MPROTO, MSTAMP, CONSTAMP, and MBX are all active. 8/91 A-32 From The N3UJJ.COM Document Library
Page 1 and 2:
PK-232 MBX Operating Manual MODEL P
Page 3 and 4:
PREFACE TO THE PK-232 OPERATING MAN
Page 5 and 6:
Timewave address is: Timewave Techn
Page 7 and 8:
CHAPTER 3 - RADIO INSTALLATION (Con
Page 9 and 10:
CHAPTER 5 - MAILDROP OPERATION (Con
Page 11 and 12:
CHAPTER 7 - AMTOR AND NAVTEX OPERAT
Page 13 and 14:
Table of Contents CHAPTER 11 - Pact
Page 15 and 16:
1.2 Computer or Computer Terminal R
Page 17 and 18:
1.4.4 Controls and Indicators Front
Page 19 and 20:
2.2.1 Connecting Power o o o o o MA
Page 21 and 22:
2.3.2 Apple Macintosh Series of Com
Page 23 and 24:
Follow the installation directions
Page 25 and 26:
Make note of the firmware Release d
Page 27 and 28:
2.6 Detailed RS-232 Connections for
Page 29 and 30:
If your computer requires any other
Page 31 and 32:
PK-232 OPERATING MANUAL RADIO INSTA
Page 33 and 34:
3.3.5 Begin Assembling your Radio C
Page 35 and 36:
3.3.6 Wiring Your HF Transceiver fo
Page 37 and 38:
3.4 PK-232 Configuration Jumpers an
Page 39 and 40:
o Listen to the monitor receiver; t
Page 41 and 42:
EXAMPLE: If the manufacturer's plat
Page 43 and 44:
4.2 Packet Introduction You've now
Page 45 and 46:
9. You have just done the three thi
Page 47 and 48:
4.3.2 What It Means There are diffe
Page 49 and 50:
4.3.3 What Happens When You Connect
Page 51 and 52:
NET/ROM, developed by Software 2000
Page 53 and 54:
After pressing , you should observe
Page 55 and 56:
4.4.4 Digipeater Details You may wi
Page 57 and 58:
If you are hearing packets that sou
Page 59 and 60:
4.4.7.2 Canceling Lines and Packets
Page 61 and 62:
4.5.1 Unconnected Packets In order
Page 63 and 64:
4.6.2 The Channel Switching Charact
Page 65 and 66:
o Make certain your HF receiver is
Page 67 and 68:
PK-232 OPERATING MANUAL PACKET RADI
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
The number "18396 free" is the RAM
Page 77 and 78:
E Shows the following short help fi
Page 79 and 80:
Enter a short (up to 27 character)
Page 81 and 82:
L {The LIST command} {The MailDrop
Page 83 and 84:
Msg# Size To From @ BBS Date Time T
Page 85 and 86:
- Use the Edit command to set the F
Page 87 and 88:
6.2.2 HF Receiver Settings Set your
Page 89 and 90:
6.4 A Typical Baudot RTTY Contact A
Page 91 and 92:
6.5.3 Formatting Your Transmitted a
Page 93 and 94:
The following parameters are the mo
Page 95 and 96:
See the MYSELCAL command in the Com
Page 97 and 98:
7.3 Transmitter Adjustments Make su
Page 99 and 100:
o Type to stop sending when the tr
Page 101 and 102:
7.4.4 Echoing Transmitted Character
Page 103 and 104:
7.6.4.1 Remote Logon to your AMTOR
Page 105 and 106:
7.6.8.4 J (JLOG) (Remote only comma
Page 107 and 108:
7.8 NAVTEX Operation NAVTEX is an i
Page 109 and 110:
o When you find a station, slowly v
Page 111 and 112:
8.4.3 Sending Only Complete Words (
Page 113 and 114:
9.3 System Setup If you own CSS HF
Page 115 and 116:
At this point make sure the THRESHO
Page 117 and 118:
9.8 Adjusting the PK-232 4.0 MHz Ma
Page 119 and 120:
o When you find a station, slowly v
Page 121 and 122: PK-232 OPERATING MANUAL SIAM AND TD
Page 123 and 124: PK-232 OPERATING MANUAL Pactor OPER
Page 133 and 134: PX-232 OPERATING MANUAL Pactor OPER
Page 139 and 140: A.2.2 Default Values Almost all com
Page 141 and 142: was now Whenever you change one of
Page 143 and 144: ?VIA You typed more than one call s
Page 145 and 146: ___________________________________
Page 147 and 148: ___________________________________
Page 149 and 150: ___________________________________
Page 151 and 152: ___________________________________
Page 153 and 154: ARQE Immediate Command Mode: Comman
Page 155 and 156: ___________________________________
Page 157 and 158: ___________________________________
Page 159 and 160: ___________________________________
Page 161 and 162: ___________________________________
Page 163 and 164: When CHCALL is OFF, the monitored a
Page 165 and 166: PK-232 OPERATING MANUAL COMMAND SUM
Page 171: ___________________________________
Page 175 and 176: ___________________________________
Page 177 and 178: ___________________________________
Page 179 and 180: 8/91 A-36b From The N3UJJ.COM Docum
Page 181 and 182: ___________________________________
Page 187 and 188: FSPEED, 8" width (narrow) FSPEED 13
Page 189 and 190: ___________________________________
Page 191 and 192: ___________________________________
Page 193 and 194: ___________________________________
Page 195 and 196: ___________________________________
Page 197 and 198: ___________________________________
Page 199 and 200: MFROM determines what packets are m
Page 201 and 202: ___________________________________
Page 203 and 204: ___________________________________
Page 209 and 210: ___________________________________
Page 215 and 216: When your computer has queued data
Page 221 and 222: ___________________________________
Page 223 and 224:
PK-232 OPERATING MANUAL COMMAND SUM
Page 225 and 226:
Page 227 and 228:
___________________________________
Page 229 and 230:
___________________________________
Page 231 and 232:
___________________________________
Page 233 and 234:
When TRFLOW is ON, the type of flow
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
PK-232 OPERATING MANUAL APPENDIX B
Page 245 and 246:
PK-232 OPERATING MANUAL APPENDIX C
Page 247 and 248:
DS16-DS20 314-302 DS10,DS11 LED GRN
Page 249 and 250:
D PK-232 OPERATING MANUAL ALINCO Fi
Page 251 and 252:
D TM-421 3 TM-431 53 7 TM-441 3 TM-
Page 253 and 254:
D 1 G G G 2 3 RX Audio: EXT SPKR Ja
Page 255 and 256:
D 1:1 Transformers 25 PTT Shield 28
Page 257 and 258:
D 0 ® ® ® RX Audio: Use EXT SPKR
Page 259 and 260:
D CQ, 4-25, 6-4, 7-1, 7-4, 8-2, 8-3
Page 261 and 262:
D NAVSTN, 7-10, A-59 NAVTEX, 1-1, 7
Page 263 and 264:
D PK-232 MBX OPERATING MANUAL COMMA
Page 265 and 266:
D PK-232 MBX OPERATING MANUAL COMMA
show all

PK-232 MBX Operating Manual - N3UJJ

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?