PathFinder Software Configuration Guide - Trilogy Communications

More documents

Recommendations

Info

15.3 Panel Logic OverviewPathFinder Version 4.22 User GuideThe standard 2RU panels provides 2 logic inputs, a Footswitch input and 2 logic outputs.The panel logics provide similar facilities to the GPI card, with the following additionalfeatures:• Each panel logic input can be assigned to cut the panel loudspeaker• The Footswitch input is assigned to mimic the downward press of any single key on thepanel.The panel logic inputs are programmed via the Panel Config / Miscellaneous page: the panellogic outputs are configured from the Logics / Logic Outputs page.Please refer to the Installation Guide for information on interfacing the Panel local logics tothird party hardware.15.4 Programming Panel Logics15.4.1 Panel Logic Input firing a crosspoint listOne or both of the panel logic inputs may be configured to fire a crosspoint list. This is a twopart operation:• Set the crosspoint to be controlled in the Crosspoint List menu.• Configure the logic input to target the crosspoint list.Refer to chapter 15.1.2.1 to explain how to set a crosspoint list.The next step is to target the crosspoint list from the logic input. Select the Miscellaneousview radio button on the Panel Conf page then pick the Logics and Inhibits icon from thePanel Logics Input field. Set the mode on the logic input to be programmed.Right click the Inhibit Target field on the logic input required to view the inhibit list pop-upand select the inhibit. Finally click the tick box to accept the edit.Note: If you wish this crosspoint created in the crosspoint list to be normally inhibited,change the logic input polarity to be normally closed.15.4.2 Panel Logic Input firing a logic outputFirst select the Miscellaneous radio button on the Panel Conf. page and pick the Logics andInhibits icon from the Panel Logics Input field. Set the mode on the logic input to beprogrammed.Next select the Logic Target field on the logic input required. Right click on this field to viewthe Logic Output list pop-up and select the output required. Finally click the tick box toaccept the edit.15.4.3 Panel Logic Input cutting the panel loudspeakerFirst select the Miscellaneous radio button on the Panel Conf page and pick theLoudspeaker Cut icon from the Panel Logics Input field. Set the mode on the logic input tobe programmed.Note: If you wish the panel loudspeaker to be normally cut, change the logic input polarity tobe normally closed.A typical view of this form is shown below.Page 94 of 94 Issue 1 Trilogy Communications Limited
PathFinder Version 4.22 User Guide15.4.4 Foot Switch InputSet the Foot Switch Key entry to the key number on the panel to be operated. The operationof the footswitch mimics the downward press of the panel key.1 2 3 4 9 10 11 12 17 18 19 205 6 7 8 13 14 15 16 21 22 23 24Note that since the panels are designed using 8 key switch units, the key layouts follow thediagram above.15.4.5 Panel AlertThis feature operates when a panel receives a 4-wire call from the matrix logic input.For information on programming the 4-wire call please refer to chapter 15.1.4.To set the panel alert, select the Miscellaneous radio button on the Panel Conf page. Rightclick on the Panel Alert Source field and from the port listing pop-up select an appropriateport input for the panel alert sound. A typical source could be one of the tones available onthe GPI card. Click the tick box to accept the edit.Trilogy Communications LimitedIssue 1Page 95 of 95
Page 1 and 2:
DIGITAL INTERCOMPathFinderVersion 4
Page 3 and 4:
PathFinder Version 4.22 User GuideE
Page 5:
PathFinder Version 4.22 User GuideS
Page 8 and 9:
PathFinder Version 4.22 User GuideS
Page 10 and 11:
PathFinder Version 4.22 User GuideP
Page 12 and 13:
Page 14 and 15:
PathFinder Version 4.22 User Guide3
Page 16 and 17:
PathFinder Version 4.22 User GuideO
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
4.1.3.1 Opening Alternate Configura
Page 24 and 25:
5.2 Navigating Between PathFinder F
Page 26 and 27:
Page 28 and 29:
5.4.7 Informational IconsPathFinder
Page 30 and 31:
PathFinder Version 4.22 User GuideT
Page 32:
Page 35 and 36:
6.5 Assigning keys to Control Panel
Page 37 and 38:
6.7 Assigning key targetsPathFinder
Page 39 and 40:
6.9 Adding a Quick Response key (QR
Page 41 and 42:
PathFinder Version 4.22 User GuideW
Page 43 and 44: PathFinder Version 4.22 User Guide7
Page 47 and 48: 7.5 Creating ConferencesPathFinder
Page 55 and 56: PathFinder Version 4.22 User GuideT
Page 61 and 62: 9.3.3 Tone BlipsPathFinder Version
Page 65 and 66: 10.1.2 Dim Level and Auto-Listen Ke
Page 67 and 68: PathFinder Version 4.22 User Guide.
Page 73 and 74: PathFinder Version 4.22 User Guide
Page 75 and 76: PathFinder Version 4.22 User GuideS
Page 81 and 82: PathFinder Version 4.22 User GuideI
Page 83 and 84: PathFinder Version 4.22 User GuideN
Page 93: PathFinder Version 4.22 User Guide1
Page 105 and 106: PathFinder Version 4.22 User Guidew
Page 109 and 110: 19.4 Network ConfigurationPathFinde
Page 111 and 112: 19.5 System OverviewPathFinder Vers
Page 115 and 116: PathFinder Version 4.22 User GuideI
Page 129 and 130: 20.7 On-LinePathFinder Version 4.22
show all

PathFinder Software Configuration Guide - Trilogy Communications

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?