PathFinder Software Configuration Guide - Trilogy Communications

More documents

Recommendations

Info

PathFinder Version 4.22 User Guide16.2 Targeting the crosspoint listA common use of the list would be to adjust a number of otherwise un-related crosspointgains simultaneously.‣ On the panel configuration form, switch to the Panel Encoders view.‣ Select the Crosspoint List Mode button and apply it to the encoder.‣ Right click in the window adjacent to the encoder and a pop-up list of currently definedlists will appear.The completed assignment now appears as below:Page 98 of 98 Issue 1 Trilogy Communications Limited
PathFinder Version 4.22 User Guide17. TELEPHONES17.1 IntroductionPathFinder provides comprehensive telephone support, allowing auto-hunting of a number ofphone lines from a single key for outgoing calls, and auto-routing of incoming calls to aspecific panel, or to a pre-configured set of panels. System wide Auto-dial numbers may beentered for speed dialling from panels. Additional hardware must be purchased andinstalled, as explained in the Installation Guide. Full facilities are only available if the TelosONE hybrid is used. This connects to the Commander matrix via the Trilogy 500-19 seriesTelephone Interface Unit. For correct operation, the port must be configured as a TelephonePort on the Overview (see below) and connected using 4 pair cable for audio and datatransfer.17.2 Configuring DTMF PortsFrom the System Overview, configure the port as Telephone Port and assign System Nameand labels.Now switch to the Telephone form, using the tab at the bottom of the screen.Trilogy Communications LimitedIssue 1Page 99 of 99
Page 1 and 2:
DIGITAL INTERCOMPathFinderVersion 4
Page 3 and 4:
PathFinder Version 4.22 User GuideE
Page 5:
PathFinder Version 4.22 User GuideS
Page 8 and 9:
PathFinder Version 4.22 User GuideS
Page 10 and 11:
PathFinder Version 4.22 User GuideP
Page 12 and 13:
Page 14 and 15:
PathFinder Version 4.22 User Guide3
Page 16 and 17:
PathFinder Version 4.22 User GuideO
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
4.1.3.1 Opening Alternate Configura
Page 24 and 25:
5.2 Navigating Between PathFinder F
Page 26 and 27:
Page 28 and 29:
5.4.7 Informational IconsPathFinder
Page 30 and 31:
PathFinder Version 4.22 User GuideT
Page 32:
Page 35 and 36:
6.5 Assigning keys to Control Panel
Page 37 and 38:
6.7 Assigning key targetsPathFinder
Page 39 and 40:
6.9 Adding a Quick Response key (QR
Page 41 and 42:
PathFinder Version 4.22 User GuideW
Page 43 and 44:
Page 45 and 46:
Page 47 and 48: 7.5 Creating ConferencesPathFinder
Page 49 and 50: PathFinder Version 4.22 User Guide7
Page 55 and 56: PathFinder Version 4.22 User GuideT
Page 61 and 62: 9.3.3 Tone BlipsPathFinder Version
Page 65 and 66: 10.1.2 Dim Level and Auto-Listen Ke
Page 67 and 68: PathFinder Version 4.22 User Guide.
Page 73 and 74: PathFinder Version 4.22 User Guide
Page 75 and 76: PathFinder Version 4.22 User GuideS
Page 81 and 82: PathFinder Version 4.22 User GuideI
Page 83 and 84: PathFinder Version 4.22 User GuideN
Page 97: PathFinder Version 4.22 User Guide1
Page 105 and 106: PathFinder Version 4.22 User Guidew
Page 109 and 110: 19.4 Network ConfigurationPathFinde
Page 111 and 112: 19.5 System OverviewPathFinder Vers
Page 115 and 116: PathFinder Version 4.22 User GuideI
Page 129 and 130: 20.7 On-LinePathFinder Version 4.22
show all

PathFinder Software Configuration Guide - Trilogy Communications

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?