SP-2000/X-Y AutoCamâ¢ Pedestal - Vinten Radamec

More documents

Recommendations

Info

SP-2000/X-YInstallationPressurizing And Balancing The PedestalIt is recommended that three people be available for this procedure.DANGER: STRICT ADHERENCE TO THESE PROCE-DURES IS CRITICAL IN ORDER TO AVOID ANYBODILY INJURY TO PERSONNEL. ALL PERSONNELWORKING ON OR NEAR THE PEDESTAL MUST BETRAINED, AWARE OF THE CORRECT PROCEDURES AND AWAREOF THE HAZARDS INVOLVED.DANGER: THE MAXIMUM CYLINDER PRESSURE IS1,250 PSI (86 BAR).USE ONLY THE VINTEN SUPPLIED MANIFOLD FORADJUSTING PRESSURE.Pressurizing The Pedestal1. Make sure that the column locking pins are NOT installed - this will allowthe column to rise as the pressure is increased.T Valve4” ExtensionFill Switch(OlderPedestals)Fill Valve(1 of 3)Fill HosePurge ValveFrom RegulatorAnd Tank3-12 User Manual
SP-2000/X-YInstallation2. Connect the input hose and regulator to the nitrogen tank. Close the regulatorvalve fully. Close the purge valve on the manifold and turn the three Tvalves fully CCW.3. Remove the yellow dust caps from the three fill valves on the column.4. Install a 4” valve extension (packed separately) onto each fill valve.Tighten the extensions with a crescent wrench - but do not overtighten.5. Connect a fill hose to each valve extension. Use one crescent wrench tohold the valve extension steady and use a second crescent wrench to tightenthe fill hose fitting. Open each T valve by turning it fully clockwise.6. With the regulator fully closed (turn CCW), open the main valve on thenitrogen tank.7. Press and hold the Standby/Charge (yellow) button on the pedestal until thelight comes on and stays on.8. If you have an older pedestal with a Fill Switch as shown opposite, pressand hold the switch while the pedestal is being pressurized, until the pedestalis powered up in step 11. (In newer pedestals, a set of contacts on theStandy/Charge switch perform the function of the Fill Switch)9. Start increasing the pressure setting on the regulator (turn CW). At approximately900 psi (63 bar) you will hear a hissing sound indicating that thethree holding chambers are being filled. Keep the regulator set just highenough to keep the nitrogen flowing but no higher. Listen for leaks at thefittings, tighten as needed.10. Have an assistant pull up gently on the payload and column (with around20-30 lb. of force) from time to time. Make sure that you support and liftthe manifold and fill hoses as the column rises to avoid straining the valveextensions. Make sure that the hoses do not get caught as the column rises.Keep nitrogen flowing until the column starts rising on its own and thenimmediately close the regulator (turn CCW) to prevent overfilling.11. Close the main valve on the nitrogen tank completely.12. Be prepared for the column to go up and down during initialization. PressRun to power up the pedestal.User Manual 3-13
Page 1 and 2: SP-2000/X-YAutoCam PedestalOperatio
Page 3 and 4: Critical Data For SP-2000/X-YMass (
Page 5 and 6: WarrantyVinten, Incorporated (Vinte
Page 7 and 8: Table Of ContentsSP-2000/X-Y Pedest
Page 9 and 10: Table Of ContentsCustomer Responsib
Page 11 and 12: 1 Safety & IntroductionUser Manual
Page 13 and 14: SP-2000/X-YSafety & IntroductionOth
Page 15 and 16: SP-2000/X-YSafety & IntroductionCAU
Page 17 and 18: SP-2000/X-YSafety & IntroductionWar
Page 19 and 20: SP-2000/X-YSafety & IntroductionHOW
Page 21 and 22: SP-2000/X-YSafety & IntroductionThi
Page 23 and 24: SP-2000/X-YSafety & IntroductionThe
Page 25 and 26: SP-2000/X-YSafety & Introductionbig
Page 27 and 28: SP-2000/X-YSafety & IntroductionTyp
Page 29 and 30: 2 OperationUser Manual 2-1
Page 31 and 32: SP-2000/X-YOperationOrientationAs a
Page 33 and 34: SP-2000/X-YOperation2. Press the St
Page 35 and 36: SP-2000/X-YOperationAfter clearing
Page 37 and 38: SP-2000/X-YOperationPedestal Active
Page 39 and 40: SP-2000/X-YOperationTargetingTarget
Page 41 and 42: 3 InstallationUser Manual 3-1
Page 43 and 44: SP-2000/X-YInstallationFloor Prepar
Page 45 and 46: SP-2000/X-YInstallation4. Using two
Page 47 and 48: SP-2000/X-YInstallation4. Plug the
Page 49 and 50: SP-2000/X-YInstallation4. Continue
Page 51: SP-2000/X-YInstallationMCB Controll
Page 55 and 56: SP-2000/X-YInstallationFinishing Up
Page 57 and 58: SP-2000/X-YInstallationThis page le
Page 59 and 60: SP-2000/X-YInstallation3. Install a
Page 61 and 62: SP-2000/X-YInstallationTechflex Inc
Page 63 and 64: SP-2000/X-YInstallationThis page le
Page 65 and 66: SP-2000/X-YInstallationCrating The
Page 67 and 68: 4 Maintenance And RepairUser Manual
Page 69 and 70: SP-2000/X-YMaintenance And RepairOt
Page 71 and 72: SP-2000/X-YMaintenance And RepairTh
Page 73 and 74: SP-2000/X-YMaintenance And Repair
Page 75 and 76: SP-2000/X-YMaintenance And RepairRe
Page 81 and 82: SP-2000/X-YMaintenance And RepairNo
Page 83 and 84: SP-2000/X-YMaintenance And Repair3.
Page 87 and 88: SP-2000/X-YMaintenance And Repair6.
Page 89 and 90: SP-2000/X-YMaintenance And RepairWA
Page 93 and 94: SP-2000/X-YMaintenance And RepairIf
Page 97 and 98: SP-2000/X-YMaintenance And RepairBa
Page 99 and 100: SP-2000/X-YMaintenance And Repair10
Page 103 and 104:
SP-2000/X-Y IndexNumerics4-Channel
Page 105 and 106:
SP-2000/X-Y IndexTarget Sensor Cali
show all

SP-2000/X-Y AutoCamâ¢ Pedestal - Vinten Radamec

Create successful ePaper yourself

Delete template?

Save as template?

SP-2000/X-Y AutoCamâ¢ Pedestal - Vinten Radamec