SP-2000/X-Y AutoCamâ¢ Pedestal - Vinten Radamec

More documents

Recommendations

Info

SP-2000/X-YMaintenance And RepairTarget Sensor CalibrationThe calibration pots and indicators for the sensors are on the Dolly Board. TheDolly Board is mounted on the West side of the pedestal and is visible throughthe removable window in the North cover. Each sensor assembly contains threeindividual sensors, each with its own calibration pot on the Dolly Board.Dolly Board WindowThe window allows you to monitor the sensor status during targeting and calibratethe sensors without removing the covers. Errors during targeting are anindication that sensor calibration and/or cleaning may be necessary. If the redERR LED flashes after targeting, this indicates that one or more sensors areincorrectly set. In normal operating mode, the “light meter” LEDs are used asindividual sensor indicators as marked on the board. Therefore, one or more ofthese LEDs will be on to indicate which sensor(s) need calibration.Dolly BoardLEDsSW1SW2Calibration Pots4-26 User Manual
SP-2000/X-YMaintenance And RepairIf you are calibrating the sensors but not cleaning them, remove the window inthe North cover and start with step 3.1. Remove the three pedestal covers and thoroughly clean the sensors asdescribed earlier in this chapter Also, clean the targets using Fantastic, 409or a similar type of household cleaner.2. When you disconnect the Stop switch harness as you remove each cover,install a jumper plug to bypass the switch and allow the pedestal to be operatedwith the covers removed.3. Power up the pedestal, allow each wheel to initialize. Select Local on theMCB controller and center the pedestal over the target. This will positionall three sensor assemblies over the target.4. Turn the rotary switch SW2 so that the index mark is on position 1. Thegreen RUN LED will turn off and the vertical row of LEDs is now functioningas a light meter. The “light meter” has 5 yellow (DS10 - DS14) and5 green (DS5 - DS9) LEDs. The space between DS9 (green) and DS10(yellow) is the threshold for detecting the white and black areas of the target.The goal during calibration is to set each sensor so that its reading forwhite (in the green region) and black (in the yellow region) is symmetricalabove and below the “threshhold” point.5. Press and release SW1, the DROP switch (located above the rotary switch)to energize the solenoids and drop the sensors. After about three minutes,the sensors will automatically retract . If the adjustments are not completedby that time, simply press and release SW1 again to drop the sensors foranother three minutes.6. Select Rotate on the MCB controller and rotate the pedestal until the Eastsensor assembly is over the black part of the target. Note which light meterLED is ON - it should be one of the yellow ones since the sensor is detectingblack.7. Rotate the pedestal until the East sensor assembly is over the white part ofthe target. Note which light meter LED is ON - it should be one of thegreen ones since the sensor is detecting white.8. If the readings in steps 6 and 7 are already symmetrical, no adjustment isrequired. For example, if the readings are the third yellow LED down andthe third green LED up, move on to step 10.9. However, if the readings are not symmetrical, adjust R1 until they are. Forexample, if the reading s are the first yellow LED down and the third greenLED up, adjust R1 until the third green LED goes out and the second greenLED comes on. Rotate the pedestal between black and white and adjust thepot until the sensor readings are symmetrical.10. Turn the rotary switch SW2 to position 2 and repeat steps 6 through 9 forthe second East sensor, adjusting R2 if necessary.11. Turn the rotary switch SW2 to position 3 and repeat steps 6 through 9 forthe third East sensor, adjusting R3 if necessary.User Manual 4-27
Page 1 and 2:
SP-2000/X-YAutoCam PedestalOperatio
Page 3 and 4:
Critical Data For SP-2000/X-YMass (
Page 5 and 6:
WarrantyVinten, Incorporated (Vinte
Page 7 and 8:
Table Of ContentsSP-2000/X-Y Pedest
Page 9 and 10:
Table Of ContentsCustomer Responsib
Page 11 and 12:
1 Safety & IntroductionUser Manual
Page 13 and 14:
SP-2000/X-YSafety & IntroductionOth
Page 15 and 16:
SP-2000/X-YSafety & IntroductionCAU
Page 17 and 18:
SP-2000/X-YSafety & IntroductionWar
Page 19 and 20:
SP-2000/X-YSafety & IntroductionHOW
Page 21 and 22:
SP-2000/X-YSafety & IntroductionThi
Page 23 and 24:
SP-2000/X-YSafety & IntroductionThe
Page 25 and 26:
SP-2000/X-YSafety & Introductionbig
Page 27 and 28:
SP-2000/X-YSafety & IntroductionTyp
Page 29 and 30:
2 OperationUser Manual 2-1
Page 31 and 32:
SP-2000/X-YOperationOrientationAs a
Page 33 and 34:
SP-2000/X-YOperation2. Press the St
Page 35 and 36:
SP-2000/X-YOperationAfter clearing
Page 37 and 38:
SP-2000/X-YOperationPedestal Active
Page 39 and 40:
SP-2000/X-YOperationTargetingTarget
Page 41 and 42: 3 InstallationUser Manual 3-1
Page 43 and 44: SP-2000/X-YInstallationFloor Prepar
Page 45 and 46: SP-2000/X-YInstallation4. Using two
Page 47 and 48: SP-2000/X-YInstallation4. Plug the
Page 49 and 50: SP-2000/X-YInstallation4. Continue
Page 51 and 52: SP-2000/X-YInstallationMCB Controll
Page 53 and 54: SP-2000/X-YInstallation2. Connect t
Page 55 and 56: SP-2000/X-YInstallationFinishing Up
Page 57 and 58: SP-2000/X-YInstallationThis page le
Page 59 and 60: SP-2000/X-YInstallation3. Install a
Page 61 and 62: SP-2000/X-YInstallationTechflex Inc
Page 63 and 64: SP-2000/X-YInstallationThis page le
Page 65 and 66: SP-2000/X-YInstallationCrating The
Page 67 and 68: 4 Maintenance And RepairUser Manual
Page 69 and 70: SP-2000/X-YMaintenance And RepairOt
Page 71 and 72: SP-2000/X-YMaintenance And RepairTh
Page 73 and 74: SP-2000/X-YMaintenance And Repair
Page 75 and 76: SP-2000/X-YMaintenance And RepairRe
Page 81 and 82: SP-2000/X-YMaintenance And RepairNo
Page 83 and 84: SP-2000/X-YMaintenance And Repair3.
Page 87 and 88: SP-2000/X-YMaintenance And Repair6.
Page 89 and 90: SP-2000/X-YMaintenance And RepairWA
Page 91: SP-2000/X-YMaintenance And RepairTh
Page 97 and 98: SP-2000/X-YMaintenance And RepairBa
Page 99 and 100: SP-2000/X-YMaintenance And Repair10
Page 103 and 104: SP-2000/X-Y IndexNumerics4-Channel
Page 105 and 106: SP-2000/X-Y IndexTarget Sensor Cali
show all

SP-2000/X-Y AutoCamâ¢ Pedestal - Vinten Radamec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

SP-2000/X-Y AutoCamâ¢ Pedestal - Vinten Radamec