SP-2000/X-Y AutoCamâ¢ Pedestal - Vinten Radamec

More documents

Recommendations

Info

SP-2000/X-YInstallationElectrical Installation And InterconnectionA typical AutoCam system configuration is shown below..1. Refer to the User Manuals for the controller, the pan/tilt head and otherequipment for relevant installation instructions.2. The rackmount power supplies are installed up to 260 ft. (80 m) from theirrespective pedestals - refer to the User Manual for the power supply foradditional information.3-18 User Manual
SP-2000/X-YInstallation3. Install an E-STOP switch for each pedestal at a convenient location close tothe joystick panel. If you are using dual controllers, install a second E-STOP switch for each pedestal at the second controller location.E-STOP SwitchE-STOPJumperE-STOP cable to power supply4. Clearly label the E-STOP switches so that the operator can see at a glancewhich switch connects to each of the pedestals.5. Connect the E-STOP cable from the E-STOP loop connector on power supply#1 to E-STOP switch #1.6. If you have a single controller, install the E-STOP jumper on the open connectoron E-STOP switch #1. If you have a sencond controller, connectanother E-STOP cable from the first E-STOP switch #1 to the second E-STOP switch #1 and install the E-STOP jumper on the second switch.7. Repeat steps 5 and 6 for the other pedestals.User Manual 3-19
Page 1 and 2:
SP-2000/X-YAutoCam PedestalOperatio
Page 3 and 4:
Critical Data For SP-2000/X-YMass (
Page 5 and 6:
WarrantyVinten, Incorporated (Vinte
Page 7 and 8: Table Of ContentsSP-2000/X-Y Pedest
Page 9 and 10: Table Of ContentsCustomer Responsib
Page 11 and 12: 1 Safety & IntroductionUser Manual
Page 13 and 14: SP-2000/X-YSafety & IntroductionOth
Page 15 and 16: SP-2000/X-YSafety & IntroductionCAU
Page 17 and 18: SP-2000/X-YSafety & IntroductionWar
Page 19 and 20: SP-2000/X-YSafety & IntroductionHOW
Page 21 and 22: SP-2000/X-YSafety & IntroductionThi
Page 23 and 24: SP-2000/X-YSafety & IntroductionThe
Page 25 and 26: SP-2000/X-YSafety & Introductionbig
Page 27 and 28: SP-2000/X-YSafety & IntroductionTyp
Page 29 and 30: 2 OperationUser Manual 2-1
Page 31 and 32: SP-2000/X-YOperationOrientationAs a
Page 33 and 34: SP-2000/X-YOperation2. Press the St
Page 35 and 36: SP-2000/X-YOperationAfter clearing
Page 37 and 38: SP-2000/X-YOperationPedestal Active
Page 39 and 40: SP-2000/X-YOperationTargetingTarget
Page 41 and 42: 3 InstallationUser Manual 3-1
Page 43 and 44: SP-2000/X-YInstallationFloor Prepar
Page 45 and 46: SP-2000/X-YInstallation4. Using two
Page 47 and 48: SP-2000/X-YInstallation4. Plug the
Page 49 and 50: SP-2000/X-YInstallation4. Continue
Page 51 and 52: SP-2000/X-YInstallationMCB Controll
Page 53 and 54: SP-2000/X-YInstallation2. Connect t
Page 55 and 56: SP-2000/X-YInstallationFinishing Up
Page 57: SP-2000/X-YInstallationThis page le
Page 61 and 62: SP-2000/X-YInstallationTechflex Inc
Page 63 and 64: SP-2000/X-YInstallationThis page le
Page 65 and 66: SP-2000/X-YInstallationCrating The
Page 67 and 68: 4 Maintenance And RepairUser Manual
Page 69 and 70: SP-2000/X-YMaintenance And RepairOt
Page 71 and 72: SP-2000/X-YMaintenance And RepairTh
Page 73 and 74: SP-2000/X-YMaintenance And Repair
Page 75 and 76: SP-2000/X-YMaintenance And RepairRe
Page 81 and 82: SP-2000/X-YMaintenance And RepairNo
Page 83 and 84: SP-2000/X-YMaintenance And Repair3.
Page 87 and 88: SP-2000/X-YMaintenance And Repair6.
Page 89 and 90: SP-2000/X-YMaintenance And RepairWA
Page 93 and 94: SP-2000/X-YMaintenance And RepairIf
Page 97 and 98: SP-2000/X-YMaintenance And RepairBa
Page 99 and 100: SP-2000/X-YMaintenance And Repair10
Page 103 and 104: SP-2000/X-Y IndexNumerics4-Channel
Page 105 and 106: SP-2000/X-Y IndexTarget Sensor Cali
show all

SP-2000/X-Y AutoCamâ¢ Pedestal - Vinten Radamec

Create successful ePaper yourself

Delete template?

Save as template?

SP-2000/X-Y AutoCamâ¢ Pedestal - Vinten Radamec