Operating instructions - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Machine description – quick overviewMachine control – Operating elements4.3 Machine control – Operating elements1M 3.73MaterialGasWiresecsecDYNsecsecsecAMPSuperpulsJOB-LIST2sec39secsec10VOLTPROGHOLDConcept48S65m/minDYN- +7Figure 4-322099-005234-EW50116.04.2012
Machine description – quick overviewMachine control – Operating elementsItem Symbol Description 01 Lid (see chap. "Machine control – concealed operating elements")2 Button, Parameter selection leftAMP Welding currentHOLDMaterial thicknessWire speedAfter each completed welding process, the last parameter values used for thewelding process are shown on the display in the main program; the signallight is on3 Display, leftWelding current, material thickness, wire speed, hold values4Rotary dial, welding parameters• Selecting the JOB (welding task)• Setting other welding parametersm/min5 Operating mode selection buttonNon-latchedLatchedSignal light lights up in green: special non-latchedSignal light lights up in red: MIG spotsSpecial latchedYou can preselect or change the operating mode at the wire feed unit (cf. "Advancedsettings > P18“).6Dynamics/choke effect buttonDYN+ Arc harder and narrower- Arc softer and wider7 Welding type buttonMIG/MAG standard weldingMIG/MAG pulse arc weldingYou can preselect or change the welding type at the wire feed unit (cf. "Advancedsettings > P18“).8 Selection of welding program, rotary dial• Selection of welding programs 0 to 15 (not possible if accessory components, suchas program torches, are connected).9 Display, rightWelding voltage, program number10 Button, Parameter selection (right)VOLT Welding voltagePROG Program numberCoolant errorTemperature error099-005234-EW50116.04.201223
Page 1 and 2: Operating instructionsWelding machi
Page 4 and 5: ContentsNotes on the use of these o
Page 6 and 7: ContentsNotes on the use of these o
Page 8 and 9: Safety instructionsExplanation of i
Page 10 and 11: Safety instructionsGeneralWARNINGEx
Page 12 and 13: Safety instructionsGeneralCAUTIONEM
Page 14 and 15: Safety instructionsTransport and in
Page 16 and 17: Intended useApplications3 Intended
Page 18 and 19: Machine description - quick overvie
Page 26 and 27: Design and functionGeneral5 Design
Page 28 and 29: Design and functionWelding torch co
Page 30 and 31: Design and functionMains connection
Page 32 and 33: Design and functionShielding gas su
Page 34 and 35: Design and functionMIG/MAG welding5
Page 40 and 41: Design and functionMIG/MAG welding
Page 42 and 43: Design and functionMIG/MAG weldingO
Page 44 and 45: Design and functionMIG/MAG weldingA
Page 50 and 51: Design and functionMIG/MAG weldingN
Page 52 and 53: Design and functionMIG/MAG weldingS
Page 54 and 55: Design and functionMIG/MAG weldingL
Page 60 and 61: Design and functionMIG/MAG weldingS
Page 70 and 71: Design and functionMIG/MAG weldingD
Page 72 and 73:
Design and functionMIG/MAG weldingE
Page 74 and 75:
Design and functionMIG/MAG weldingS
Page 76 and 77:
Design and functionMIG/MAG weldingS
Page 78 and 79:
Design and functionTIG welding5.10.
Page 80 and 81:
Design and functionTIG weldingNon-l
Page 82 and 83:
Design and functionTIG weldingLatch
Page 84 and 85:
Design and functionMMA welding5.11
Page 86 and 87:
Design and functionMMA welding5.11.
Page 88 and 89:
Maintenance, care and disposalGener
Page 90 and 91:
Maintenance, care and disposalDispo
Page 92 and 93:
Rectifying faultsError messages (po
Page 94 and 95:
Rectifying faultsResetting JOBs (we
Page 96 and 97:
Rectifying faultsVent coolant circu
Page 98 and 99:
Technical dataPhoenix 401 Concept p
Page 100 and 101:
Replaceable partsWire feed rollers1
Page 102 and 103:
Fülldraht / Flux-CoredMassivdraht
show all

Operating instructions - EWM Hightec Welding GmbH

Create successful ePaper yourself

Delete template?

Save as template?