Operating instructions - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Design and functionMMA welding5.11.3 HotstartThe hotstart device improves the ignition of the stick electrodes using an increased ignition current.a) = Hotstart timeb) = Hotstart currentI = <strong>Welding</strong> currentt = Time5.11.4 AntistickFigure 5-50Anti-stick prevents the electrode from annealing.If the electrode sticks in spite of the Arcforce device, themachine automatically switches over to the minimumcurrent within about 1 second to prevent the electrodefrom overheating. Check the welding current settingand correct according to the welding task!Figure 5-515.11.5 Parameter overview213sec4secDYNsecsecsecsecSuperpulssecsecFigure 5-52Basic parametersItem Meaning/explanation Setting range1 <strong>Welding</strong> current 5 A to maximum welding current2 Hotstart time 0 to 20 s3 Hotstart current 0 to 200 %4 Arcforce -40 to 40NOTEThe hotstart current is a percentage based on the welding current selected.86099-005234-EW50116.04.2012
Design and functionPC Interfaces5.12 PC InterfacesCAUTIONEquipment damage or faults may occur if the PC is connected incorrectly!Not using the SECINT X10USB interface results in equipment damage or faults in signaltransmission. The PC may be destroyed due to high frequency ignition pulses.• Interface SECINT X10USB must be connected between the PC and the welding machine!• The connection must only be made using the cables supplied (do not use any additionalextension cables)!NOTEPlease note the relevant documentation of the accessory components.PC 300 welding parameter softwareCreate all welding parameters quickly on the PC and easily transfer them to one or more weldingmachines (accessories: set consisting of software, interface, connection leads).099-005234-EW50116.04.201287
Page 1 and 2:
Operating instructionsWelding machi
Page 4 and 5:
ContentsNotes on the use of these o
Page 6 and 7:
ContentsNotes on the use of these o
Page 8 and 9:
Safety instructionsExplanation of i
Page 10 and 11:
Safety instructionsGeneralWARNINGEx
Page 12 and 13:
Safety instructionsGeneralCAUTIONEM
Page 14 and 15:
Safety instructionsTransport and in
Page 16 and 17:
Intended useApplications3 Intended
Page 18 and 19:
Machine description - quick overvie
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Design and functionGeneral5 Design
Page 28 and 29:
Design and functionWelding torch co
Page 30 and 31:
Design and functionMains connection
Page 32 and 33:
Design and functionShielding gas su
Page 34 and 35:
Design and functionMIG/MAG welding5
Page 36 and 37: Design and functionMIG/MAG welding5
Page 40 and 41: Design and functionMIG/MAG welding
Page 42 and 43: Design and functionMIG/MAG weldingO
Page 44 and 45: Design and functionMIG/MAG weldingA
Page 50 and 51: Design and functionMIG/MAG weldingN
Page 52 and 53: Design and functionMIG/MAG weldingS
Page 54 and 55: Design and functionMIG/MAG weldingL
Page 70 and 71: Design and functionMIG/MAG weldingD
Page 72 and 73: Design and functionMIG/MAG weldingE
Page 78 and 79: Design and functionTIG welding5.10.
Page 80 and 81: Design and functionTIG weldingNon-l
Page 82 and 83: Design and functionTIG weldingLatch
Page 84 and 85: Design and functionMMA welding5.11
Page 88 and 89: Maintenance, care and disposalGener
Page 90 and 91: Maintenance, care and disposalDispo
Page 92 and 93: Rectifying faultsError messages (po
Page 94 and 95: Rectifying faultsResetting JOBs (we
Page 96 and 97: Rectifying faultsVent coolant circu
Page 98 and 99: Technical dataPhoenix 401 Concept p
Page 100 and 101: Replaceable partsWire feed rollers1
Page 102 and 103: Fülldraht / Flux-CoredMassivdraht
show all

Operating instructions - EWM Hightec Welding GmbH

Create successful ePaper yourself

Delete template?

Save as template?