Operating instructions - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Rectifying faultsResetting JOBs (welding tasks) to the factory settings7.3 Resetting JOBs (welding tasks) to the factory settings7.3.1 Resetting a single JOBNOTEAll customised welding parameters that are stored will be replaced by the factorysettings.JOB-LISTJOB-LISTm/minFigure 7-1DisplaySetting/selectionReset to factory settingsThe RESET will be done after pressing the button.The menu will be ended when no changes are done after 3 sec.JOB-number (example)The shown JOB will be set to ex works.94099-005234-EW50116.04.2012
Rectifying faultsGeneral operating problems7.3.2 Resetting all JOBsJOBs 1–128 and 170–256 will be reset.Custom JOBs 129–169 are maintained.NOTEJOB-LISTJOB-LISTm/minDisplaySetting/selectionFigure 7-2Reset to factory settingsThe RESET will be done after pressing the button.The menu will be ended when no changes are done after 3 sec.7.4 General operating problems7.4.1 Interface for mechanised weldingWARNINGNo function of the external shut-down devices (emergency stop switch)!If the emergency stop circuit has been realised using an external shut-down device viathe interface for mechanised welding, the device must be set for this setup. If this is notobserved, the power source will ignore the external shut-down devices and will not shutdown!• Disconnect jumper 1 on PCB T320/1 (Tetrix) or M320/1 (Phoenix / alpha Q)!099-005234-EW50116.04.201295
Page 1 and 2:
Operating instructionsWelding machi
Page 4 and 5:
ContentsNotes on the use of these o
Page 6 and 7:
ContentsNotes on the use of these o
Page 8 and 9:
Safety instructionsExplanation of i
Page 10 and 11:
Safety instructionsGeneralWARNINGEx
Page 12 and 13:
Safety instructionsGeneralCAUTIONEM
Page 14 and 15:
Safety instructionsTransport and in
Page 16 and 17:
Intended useApplications3 Intended
Page 18 and 19:
Machine description - quick overvie
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Design and functionGeneral5 Design
Page 28 and 29:
Design and functionWelding torch co
Page 30 and 31:
Design and functionMains connection
Page 32 and 33:
Design and functionShielding gas su
Page 34 and 35:
Design and functionMIG/MAG welding5
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Design and functionMIG/MAG welding
Page 42 and 43:
Design and functionMIG/MAG weldingO
Page 44 and 45: Design and functionMIG/MAG weldingA
Page 46 and 47: Design and functionMIG/MAG welding5
Page 50 and 51: Design and functionMIG/MAG weldingN
Page 52 and 53: Design and functionMIG/MAG weldingS
Page 54 and 55: Design and functionMIG/MAG weldingL
Page 70 and 71: Design and functionMIG/MAG weldingD
Page 72 and 73: Design and functionMIG/MAG weldingE
Page 78 and 79: Design and functionTIG welding5.10.
Page 80 and 81: Design and functionTIG weldingNon-l
Page 82 and 83: Design and functionTIG weldingLatch
Page 84 and 85: Design and functionMMA welding5.11
Page 86 and 87: Design and functionMMA welding5.11.
Page 88 and 89: Maintenance, care and disposalGener
Page 90 and 91: Maintenance, care and disposalDispo
Page 92 and 93: Rectifying faultsError messages (po
Page 96 and 97: Rectifying faultsVent coolant circu
Page 98 and 99: Technical dataPhoenix 401 Concept p
Page 100 and 101: Replaceable partsWire feed rollers1
Page 102 and 103: Fülldraht / Flux-CoredMassivdraht
show all

Operating instructions - EWM Hightec Welding GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?