Operating instructions - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Design and functionMains connection5.6 Mains connectionDANGERHazard caused by improper mains connection!An improper mains connection can cause injuries or damage property!• Only use machine with a plug socket that has a correctly fitted protective conductor.• If a mains plug must be fitted, this may only be carried out by an electrician in accordancewith the relevant national provisions or regulations!• Mains plug, socket and lead must be checked regularly by an electrician!• When operating the generator always ensure it is earthed as stated in the operatinginstructions. The resulting network has to be suitable for operating devices according toprotection class 1.5.6.1 Mains configurationNOTEThe machine may be connected to:• a three-phase system with four conductors and an earthed neutral conductor• a three-phase system with three conductors of which any one can be earthed,e.g. the outer conductorFigure 5-2LegendItem Designation Colour codeL1 Outer conductor 1 brownL2 Outer conductor 2 blackL3 Outer conductor 3 greyN Neutral conductor bluePE Protective conductor green-yellowCAUTIONOperating voltage - mains voltage!The operating voltage shown on the rating plate must be consistent with the mainsvoltage, in order to avoid damage to the machine!• For mains fuse protection, please refer to the “Technical data” chapter!• Insert mains plug of the switched-off machine into the appropriate socket.30099-005234-EW50116.04.2012
Design and functionShielding gas supply5.7 Shielding gas supply5.7.1 Connecting the shielding gas supplyWARNINGRisk of injury due to improper handling of shielding gas cylinders!Improper handling and insufficient securing of shielding gas cylinderscan cause serious injuries!• Secure shielding gas cylinders using the standard fastening elements onthe unit (chain/belt)!• The fastening elements must tightly enclose the shielding gas cylinder!• Attach the fastening elements within the upper half of the shielding gascylinder!• Do not attach any element to the shielding gas cylinder valve!• Observe the instructions from the gas manufacturer and any relevantregulations concerning the use of compressed air!• Avoid heating the shielding gas cylinder!CAUTIONFaults in the shielding gas supply.An unhindered shielding gas supply from the shielding gas cylinder to the weldingtorch is a fundamental requirement for optimum welding results. In addition, a blockedshielding gas supply may result in the welding torch being destroyed.• Always re-fit the yellow protective cap when not using the shielding gas connection.• All shielding gas connections must be gas tight.NOTEBefore connecting the pressure regulator to the gas cylinder, open the cylinder valvebriefly to expel any dirt.099-005234-EW50116.04.201231
Page 1 and 2: Operating instructionsWelding machi
Page 4 and 5: ContentsNotes on the use of these o
Page 6 and 7: ContentsNotes on the use of these o
Page 8 and 9: Safety instructionsExplanation of i
Page 10 and 11: Safety instructionsGeneralWARNINGEx
Page 12 and 13: Safety instructionsGeneralCAUTIONEM
Page 14 and 15: Safety instructionsTransport and in
Page 16 and 17: Intended useApplications3 Intended
Page 18 and 19: Machine description - quick overvie
Page 26 and 27: Design and functionGeneral5 Design
Page 28 and 29: Design and functionWelding torch co
Page 32 and 33: Design and functionShielding gas su
Page 34 and 35: Design and functionMIG/MAG welding5
Page 40 and 41: Design and functionMIG/MAG welding
Page 42 and 43: Design and functionMIG/MAG weldingO
Page 44 and 45: Design and functionMIG/MAG weldingA
Page 50 and 51: Design and functionMIG/MAG weldingN
Page 52 and 53: Design and functionMIG/MAG weldingS
Page 54 and 55: Design and functionMIG/MAG weldingL
Page 70 and 71: Design and functionMIG/MAG weldingD
Page 72 and 73: Design and functionMIG/MAG weldingE
Page 78 and 79: Design and functionTIG welding5.10.
Page 80 and 81:
Design and functionTIG weldingNon-l
Page 82 and 83:
Design and functionTIG weldingLatch
Page 84 and 85:
Design and functionMMA welding5.11
Page 86 and 87:
Design and functionMMA welding5.11.
Page 88 and 89:
Maintenance, care and disposalGener
Page 90 and 91:
Maintenance, care and disposalDispo
Page 92 and 93:
Rectifying faultsError messages (po
Page 94 and 95:
Rectifying faultsResetting JOBs (we
Page 96 and 97:
Rectifying faultsVent coolant circu
Page 98 and 99:
Technical dataPhoenix 401 Concept p
Page 100 and 101:
Replaceable partsWire feed rollers1
Page 102 and 103:
Fülldraht / Flux-CoredMassivdraht
show all

Operating instructions - EWM Hightec Welding GmbH

Create successful ePaper yourself

Delete template?

Save as template?