Operating instructions - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Machine description – quick overviewMachine control – <strong>Operating</strong> elements4.3.1 Covered operating elements4 31617M 3.73MaterialGasWiresec8sec5 7 6 10 9DYNsecsecsec11 1218SuperpulsJOB-LISTsec2 15 113sec14sec19Figure 4-4Item Symbol Description 01 Select welding parameters buttonThis button is used to select the welding parameters depending on the welding processand operating mode used.2 Signal light, gas pre-flow timeSetting range 0.0 s to 20.0 s3 Signal light, start program (P START)• Wire speed:1% to 200% of the main program P A• Correction of the arc length -9.9 V to +9.9 V4 sec Signal light, start timeSetting range, absolute 0.0 s to 20.0 s (0.1 s increments)5 sec Signal light, slope time program P STARTto main program P ASetting range 0.0 s to 20.0 s (0.1 s increments)6 Signal light, main program (P A)• Wire speed WF-min. to WF-max.• Correction of the arc length -9.9 V to +9.9 V7 DYN Signal light, dynamicsSetting range -40 to +408 sec Signal light, duration of main program P ASetting range 0.0 s to 20.0 s (0.1 s increments).Used e.g. in connection with the super pulse function9 Signal light, reduced main program (P B)• Wire speed:1% to 200% of the main program P A• Correction of the arc length -9.9 V to +9.9 V10 sec Signal light, duration reduced main program P BSetting range 0.0 s to 20.0 s (0.1 s increments).Used e.g. in connection with the super pulse function.11 sec Signal light, slope time program P A(or P B) to end program P ENDSetting range 0.0 s to 20.0 s (0.1 s increments)12 Signal light, end program (P END)• Wire speed:1% to 200% of the main program P A• Correction of the arc length -9.9 V to +9.9 V13 sec Signal light, duration of end program P ENDSetting range 0.0 s to 20.0 s (0.1 s increments)14 Signal light, gas post-flow timeSetting range 0.0 s to 20.0 s24099-005234-EW50116.04.2012
Machine description – quick overviewMachine control – <strong>Operating</strong> elementsItem Symbol Description 015 Superpuls16MaterialGasWire17JOB-LISTSignal lamp, super pulse functionLights up when the super pulse function is active.Signal light, JOB-ListIlluminates upon display or selection of the JOB numberKey button, JOB-ListSelection of the welding task (JOB) from the JOB list18 Wire inching buttonSee also “Inching the Wire Electrode” chapter19 Gas test / rinse button• Gas test: For setting the shielding gas quantity• Rinse: For rinsing longer tube packagesSee also "Shielding Gas Supply" chapter099-005234-EW50116.04.201225
Page 1 and 2: Operating instructionsWelding machi
Page 4 and 5: ContentsNotes on the use of these o
Page 6 and 7: ContentsNotes on the use of these o
Page 8 and 9: Safety instructionsExplanation of i
Page 10 and 11: Safety instructionsGeneralWARNINGEx
Page 12 and 13: Safety instructionsGeneralCAUTIONEM
Page 14 and 15: Safety instructionsTransport and in
Page 16 and 17: Intended useApplications3 Intended
Page 18 and 19: Machine description - quick overvie
Page 26 and 27: Design and functionGeneral5 Design
Page 28 and 29: Design and functionWelding torch co
Page 30 and 31: Design and functionMains connection
Page 32 and 33: Design and functionShielding gas su
Page 34 and 35: Design and functionMIG/MAG welding5
Page 40 and 41: Design and functionMIG/MAG welding
Page 42 and 43: Design and functionMIG/MAG weldingO
Page 44 and 45: Design and functionMIG/MAG weldingA
Page 50 and 51: Design and functionMIG/MAG weldingN
Page 52 and 53: Design and functionMIG/MAG weldingS
Page 54 and 55: Design and functionMIG/MAG weldingL
Page 60 and 61: Design and functionMIG/MAG weldingS
Page 70 and 71: Design and functionMIG/MAG weldingD
Page 72 and 73: Design and functionMIG/MAG weldingE
Page 74 and 75:
Design and functionMIG/MAG weldingS
Page 76 and 77:
Design and functionMIG/MAG weldingS
Page 78 and 79:
Design and functionTIG welding5.10.
Page 80 and 81:
Design and functionTIG weldingNon-l
Page 82 and 83:
Design and functionTIG weldingLatch
Page 84 and 85:
Design and functionMMA welding5.11
Page 86 and 87:
Design and functionMMA welding5.11.
Page 88 and 89:
Maintenance, care and disposalGener
Page 90 and 91:
Maintenance, care and disposalDispo
Page 92 and 93:
Rectifying faultsError messages (po
Page 94 and 95:
Rectifying faultsResetting JOBs (we
Page 96 and 97:
Rectifying faultsVent coolant circu
Page 98 and 99:
Technical dataPhoenix 401 Concept p
Page 100 and 101:
Replaceable partsWire feed rollers1
Page 102 and 103:
Fülldraht / Flux-CoredMassivdraht
show all

Operating instructions - EWM Hightec Welding GmbH

Create successful ePaper yourself

Delete template?

Save as template?