Operating instructions - EWM Hightec Welding GmbH

More documents

Recommendations

Info

Design and functionMIG/MAG welding5.9.16 Standard MIG/MAG torchThe MIG welding torch trigger is essentially used to start and stop the welding process.<strong>Operating</strong> elementsFunctionsTorch trigger • Start/stop weldingOther functions are also possible by tapping the torch trigger, depending on the machine typeand control configuration:• Change over between welding programs (see "Program changeover with standard torches (P8)"chapter).• Program selection before starting welding (see chapter entitled "Selecting programs with the standardtorch trigger (P17)").5.9.17 Remote controlCAUTIONDamage to the machine due to improper connection!The remote controls have been developed to be connected to welding machines or wirefeed units only. Connecting them to other machines may cause damage to themachines!• Observe the operating <strong>instructions</strong> for the welding machine or wire feed unit!• Switch off the welding machine before connecting!The operation of the remote control and its settings are directly dependent on the configuration of therespective welding machine or wire feed unit. The settings are defined by changeover switches or bysetting special parameters (dependent on the control).• Infinitely adjust wire feed speed and arc length correction (welding voltage) (the function is onlyavailable in program 0). Switch the “welding torch function” changeover switch to the program position.Special functions• Adjust wire feed speed and arc length correction within defined limits.The function can only be enabled in connection with an M3.7x machine control.Special parameter P7 must be switched on (see corresponding documentation).The function can be used in all programs except program 0.5.9.18 MIG/MAG automatic cut-outNOTEThe welding machine ends the ignition process or the welding process with an• Ignition fault (no welding current flows within 5 s after the start signal).• Arc interruption (arc is intrerupted for longer than 3 s).68099-005234-EW50116.04.2012
Design and functionMIG/MAG welding5.9.19 Advanced settingsThe special parameters cannot be viewed directly since they are normally only set and stored once. Themachine control offers the following special functions:5.9.19.1 Selecting, changing and saving parameters0lAMPVOLTPROGHOLDm/minm/minFigure 5-37NOTEENTER (Enter the menu)• Switch off machine at the main switch.• Press and hold the "left parameter selection" button and switch the machine on again at thesame time.NAVIGATION (Navigate the menu)• Select parameters by turning the "welding parameter setting" rotary dial.• Set or change the parameters by turning the "arc length correction/select welding program"rotary dial.EXIT (Exit the menu)• Press the "right parameter selection" button (switch machine off and on again).099-005234-EW50116.04.201269
Page 1 and 2:
Operating instructionsWelding machi
Page 4 and 5:
ContentsNotes on the use of these o
Page 6 and 7:
ContentsNotes on the use of these o
Page 8 and 9:
Safety instructionsExplanation of i
Page 10 and 11:
Safety instructionsGeneralWARNINGEx
Page 12 and 13:
Safety instructionsGeneralCAUTIONEM
Page 14 and 15:
Safety instructionsTransport and in
Page 16 and 17:
Intended useApplications3 Intended
Page 18 and 19: Machine description - quick overvie
Page 26 and 27: Design and functionGeneral5 Design
Page 28 and 29: Design and functionWelding torch co
Page 30 and 31: Design and functionMains connection
Page 32 and 33: Design and functionShielding gas su
Page 34 and 35: Design and functionMIG/MAG welding5
Page 40 and 41: Design and functionMIG/MAG welding
Page 42 and 43: Design and functionMIG/MAG weldingO
Page 44 and 45: Design and functionMIG/MAG weldingA
Page 50 and 51: Design and functionMIG/MAG weldingN
Page 52 and 53: Design and functionMIG/MAG weldingS
Page 54 and 55: Design and functionMIG/MAG weldingL
Page 70 and 71: Design and functionMIG/MAG weldingD
Page 72 and 73: Design and functionMIG/MAG weldingE
Page 78 and 79: Design and functionTIG welding5.10.
Page 80 and 81: Design and functionTIG weldingNon-l
Page 82 and 83: Design and functionTIG weldingLatch
Page 84 and 85: Design and functionMMA welding5.11
Page 86 and 87: Design and functionMMA welding5.11.
Page 88 and 89: Maintenance, care and disposalGener
Page 90 and 91: Maintenance, care and disposalDispo
Page 92 and 93: Rectifying faultsError messages (po
Page 94 and 95: Rectifying faultsResetting JOBs (we
Page 96 and 97: Rectifying faultsVent coolant circu
Page 98 and 99: Technical dataPhoenix 401 Concept p
Page 100 and 101: Replaceable partsWire feed rollers1
Page 102 and 103: Fülldraht / Flux-CoredMassivdraht
show all

Operating instructions - EWM Hightec Welding GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?