GA-K8VM800M / GA-K8VM800M-RH - visit site - Gigabyte

More documents

Recommendations

Info

English 1-3 Installation of the CPU and Heatsink Before installing the CPU, please comply with the following conditions: 1. Please make sure that the motherboard supports the CPU. 2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU. 3. Please add an even layer of heat sink paste between the CPU and heatsink. 4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur. 5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc. 1-3-1 Installation of the CPU Check the processor pins to see that none are bent. Move the socket lever to the unlocked position as shown in Figure 1.(90 o to the plane of the motherboard) prior to inserting the processor. The pin 1 location is designated on the processor by a copper triangle that matches up to a triangle on the socket as shown in Figure 2. Align the processor to the socket and gently lower it into place. Do not force the processor into the socket. Socket lever Fig.1 Position lever at a 90 degree angle. GA-K8VM800M(-RH) Motherboard - 12 - Fig.2 Pin 1 location on the socket and processor. Gently place the CPU into position making sure that the CPU pins fit perfectly into their holes. Once the CPU is positioned into its socket, place one finger down on the middle of the CPU and gently press the metal lever back into its original position. Please use extra care when installing the CPU. The CPU will not fit if positioned incorrectly. Rather than applying force, please change the positioning of the CPU.
1-3-2 Installation of the Heatsink Fig.1 Before installing the heat sink, please first add an even layer of heat sink paste on the surface of the CPU. Install all the heat sink components (Please refer to the heat sink manual for detailed installation instructions). Fig.2 Please connect the heat sink power connector to the CPU_FAN connector located on the motherboard so that the heat sink can properly function to prevent CPU overheating. The heat sink may adhere to the CPU as a result of hardening of the heat sink paste. To prevent such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for heat dissipation or using extreme care when removing the heat sink. - 13 - Hardware Installation English
Page 1 and 2: GA-K8VM800M / GA-K8VM800M-RH AMD So
Page 3 and 4: Jun. 21, 2006 Jun. 21, 2006 GA-K8VM
Page 5 and 6: Table of Contents GA-K8VM800M(-RH)
Page 7 and 8: GA-K8VM800M(-RH) Motherboard Layout
Page 9 and 10: Chapter 1Hardware Installation 1-1
Page 11: On-Board SATA RAID � Built in VIA
Page 15 and 16: 1-5 Installation of Expansion Cards
Page 17 and 18: 1-7 Connectors Introduction 1) ATX_
Page 19 and 20: 3/4) CPU_FAN / SYS_FAN (Cooler Fan
Page 21 and 22: 8) F_PANEL (Front Panel Jumper) Ple
Page 23 and 24: 11) CD_IN (CD In Connector) Connect
Page 25 and 26: 15) COMB (COMB Connector) Be carefu
Page 27 and 28: Chapter 2 BIOS Setup BIOS (Basic In
Page 29 and 30: �� Load Optimized Defa
Page 31 and 32: Capacity Capacity of currently inst
Page 33 and 34: 2-3 Integrated Peripherals CMOS Set
Page 35 and 36: Onboard Serial Port 2 Auto BIOS wil
Page 37 and 38: Mouse Power On Disabled Disabled th
Page 39 and 40: 2-6 PC Health Status Current Voltag
Page 41 and 42: 2-8 Load Fail-Safe Defaults � Sta
Page 43 and 44: 2-11 Save & Exit Setup � Standard
Page 45 and 46: Chapter 3Drivers Installation Pictu
Page 47 and 48: 3-4 Hardware Information This page
Page 49 and 50: Chapter 4 Appendix 4-1 Unique Softw
Page 51 and 52: 4-1-2 Xpress Recovery Introduction
Page 53 and 54: 1. Execute Backup Utility: ��
Page 55 and 56: Entering the Q-Flash TM utility: St
Page 57 and 58: 3. Press Y button on your keyboard
Page 59 and 60: Exploring the Q-Flash TM utility sc
Page 61 and 62: Method 2 : @BIOS TM Utility If you
Page 63 and 64:
4-1-4 Serial ATA BIOS Setting Utili
Page 65 and 66:
A. Create Array: Press Enter on Cre
Page 67 and 68:
B. Delete Array: If you want to del
Page 69 and 70:
Installing the RAID drivers To inst
Page 71 and 72:
4 Channel Analog Audio Output Mode
Page 73 and 74:
SPDIF Output Device (Optional Devic
Page 75 and 76:
- 75 - Appendix English
Page 77 and 78:
- 77 - Appendix English
Page 79 and 80:
Contact Us �� Taiwan (
show all

GA-K8VM800M / GA-K8VM800M-RH - visit site - Gigabyte

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?