DTM for EtherNet/IP Scanner Devices - Hilscher
DTM for EtherNet/IP Scanner Devices - Hilscher
DTM for EtherNet/IP Scanner Devices - Hilscher
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Settings 37/149<br />
Parameter Meaning Range of Value /<br />
Value<br />
Device selection Selecting suitable only or all devices. suitable only, all<br />
Device Device class of the <strong>EtherNet</strong>/<strong>IP</strong> <strong>Scanner</strong> <strong>Devices</strong>.<br />
Hardware Port<br />
0/1/2/3<br />
Shows, which hardware is assigned to which communication<br />
interface.<br />
Slot number Shows the Slot Number (Card ID) preset at the cifX card via<br />
the Rotary Switch Slot Number (Card ID).<br />
The indication n/a means, that no Slot-Nummer (Karten-ID)<br />
exists. This occurs, if the cifX card is not equipped with a<br />
Rotary Switch Slot Number (Card ID) or <strong>for</strong> cifX cards<br />
equipped with a Rotary Switch Slot Number (Card ID), if the<br />
rotary switch is set to the value 0 (zero).<br />
Serial number Serial number of the device<br />
Driver Name of the driver<br />
Channel Protocol Shows, which firmware is loaded to which device channel.<br />
The data <strong>for</strong> the used channel consists of the protocol class<br />
and the communication class.<br />
a.) For devices without firmware: Undefined Undefined,<br />
b.) For devices with firmware: Protocol name corresponding<br />
to the used Firmware<br />
Access path<br />
(under Device<br />
selection last<br />
column on the<br />
right)<br />
Access path<br />
(at the lower side<br />
of the dialog<br />
pane)<br />
Depending on the used driver in the column Access path<br />
different data to the device are displayed.<br />
For the cifX Device Driver the following data are displayed:<br />
a.) For devices without firmware: …\cifX[0toN]_SYS,<br />
b.) For devices with firmware: …\cifX[0toN]_Ch[0to3].<br />
cifX[0toN] = Board number 0 to N<br />
Ch[0to3] = Channel number 0 to 3<br />
If under Device selection the check box <strong>for</strong> a device is<br />
checked, under Access path (at the lower side of the dialog<br />
pane) the driver identification or depending on the used driver<br />
additional data to the device.<br />
For the cifX Device Driver the following data are displayed:<br />
a.) For devices without firmware: …\cifX[0toN]_SYS,<br />
b.) For devices with firmware: …\cifX[0toN]_Ch[0to3].<br />
cifX[0toN] = Board number 0 to N<br />
Ch[0to3] = Channel number 0 to 3<br />
Table 14: Parameters of the Device Assignment<br />
1 to 9,<br />
n/a<br />
Depending on the<br />
device and on the<br />
driver:<br />
board or channel<br />
number, <strong>IP</strong> address<br />
or COM interface<br />
driver identification<br />
(ID)<br />
depending on the<br />
device and on the<br />
driver:<br />
board or channel<br />
number, <strong>IP</strong> address<br />
or COM interface<br />
<strong>DTM</strong> <strong>for</strong> <strong>EtherNet</strong>/<strong>IP</strong> <strong>Scanner</strong> <strong>Devices</strong> | Configuration of <strong>EtherNet</strong>/<strong>IP</strong> <strong>Scanner</strong> <strong>Devices</strong><br />
DOC061201OI06EN | Revision 6 | English | 2010-08 | Released | Public © <strong>Hilscher</strong>, 2006-2010