VessRAID Setup - Promise Technology, Inc.

More documents

Recommendations

Info

VessRAID 1000i Series Product Manual 4. Open the root folder of the USB stick and copy the file subinfo_xxxxxxxxxx.log to the PC desktop or a convenient location. Figure 12.Locating the report file on the USB stick 5. Open the subinfo_xxxxxxxxxx.log file in a text editor to read the system profile and diagnostic report. 288 Note Choose a text editor with some word processor capability, such as WordPad on a Windows PC, for easier viewing.
Event Notification Response 289 Chapter 9: Troubleshooting When you choose Event Notification, WebPAM PROe sends popup and/or email messages regarding its status. The messages you see depend on your notification selection and what is currently happening in the VessRAID. See “Setting-up User Event Subscriptions” on page 63. The table below cites: • Reported Events – Events that require you to take action • Corrective Actions – The action you should take in response to the event A list of event categories is shown below. • Battery (page 289) • Blowers (page 290) • Cache (page 291) • Controller (page 291) • Disk Array (page 291) • Drive Interface Controller (page 292) • Enclosure (page 292) • Event Log (page 292) • Host Interface Controller (page 292) • Logical Drive (page 293) • Media Patrol (page 294) • Online Capacity Expansion (page 295) • PDM (page 295) • Physical Disk (page 296) • PSU (Power Supply Units) (page 297) • RAID Level Migration (page 298) • Rebuild (page 298) • Redundancy Check (page 299) • Resource (page 300) • Spare Check (page 300) • Spare Drives (page 300) • SMART (page 300) • Synchronization (page 300) • System (VessRAID) (page 301) • Transition (page 301) • Watermark (page 301) Reported Event Corrective Action Battery Battery temperature is above the threshold Battery temperature is normal Battery capacity is below the threshold The battery is too hot. Verify proper airflow around the through the VessRAID. If airflow is OK, replace the battery. See page 240. Normal. Battery capacity is normal Normal. Battery is drained. Run battery reconditioning. See page 103 (WebPAM PROe) or page 153 (CLU).
Page 1 and 2:
VessRAID 1720i, 1730i, 1740i, 1820i
Page 3 and 4:
Contents Chapter 1: Introduction to
Page 5 and 6:
v Contents Chapter 4: Management wi
Page 7 and 8:
vii Contents Chapter 4: Management
Page 9 and 10:
ix Contents Chapter 5: Management w
Page 11 and 12:
xi Contents Chapter 5: Management w
Page 13 and 14:
xiii Contents Chapter 6: Management
Page 15 and 16:
xv Contents Chapter 9: Troubleshoot
Page 17 and 18:
Chapter 1: Introduction to VessRAID
Page 19 and 20:
Architectural Description 3 Chapter
Page 21 and 22:
5 Chapter 1: Introduction to VessRA
Page 23 and 24:
Dimensions (H x W x D) 1840i: 13 x
Page 25 and 26:
Chapter 2: VessRAID Installation Th
Page 27 and 28:
Figure 3. VessRAID 1830i rear view
Page 29 and 30:
Mounting VessRAID in a Rack 13 Chap
Page 31 and 32:
Installing Disk Drives 15 Chapter 2
Page 33 and 34:
Installing Your Disk Drives 17 Chap
Page 35 and 36:
19 Chapter 2: VessRAID Installation
Page 37 and 38:
21 Chapter 2: VessRAID Installation
Page 39 and 40:
Setting Up Serial Cable Connections
Page 41 and 42:
Controller LEDs 25 Chapter 2: VessR
Page 43 and 44:
Chapter 3: VessRAID Setup This chap
Page 45 and 46:
Setting up with the CLI 29 Chapter
Page 47 and 48:
Setting up with the CLU 1. At the a
Page 49 and 50:
Setting up with the LCD 33 Chapter
Page 51 and 52:
Creating Disk Arrays with WebPAM PR
Page 53 and 54:
Selecting a Language 37 Chapter 3:
Page 55 and 56:
Express 39 Chapter 3: VessRAID Setu
Page 57 and 58:
41 Chapter 3: VessRAID Setup 5. Spe
Page 59 and 60:
Chapter 4: Management with WebPAM P
Page 61 and 62:
Figure 1. WebPAM PROe log-in screen
Page 63 and 64:
There are four major parts to the g
Page 65 and 66:
49 Chapter 4: Management with WebPA
Page 67 and 68:
Working with the Storage Network 51
Page 69 and 70:
Setting an Alias for the Subsystem
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
8. Enter the new password in the Re
Page 83 and 84:
Managing the Network Connection 67
Page 85 and 86:
Managing iSCSI Connections 69 Chapt
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Deleting CHAPs 75 Chapter 4: Manage
Page 93 and 94:
Page 95 and 96:
Managing Software Services Software
Page 97 and 98:
Starting or Restarting SLP service
Page 99 and 100:
Starting or Restarting Telnet servi
Page 101 and 102:
Adding Netsend recipients 85 Chapte
Page 103 and 104:
Exporting the User Database 87 Chap
Page 105 and 106:
Page 107 and 108:
Shutting Down the Subsystem 91 Chap
Page 109 and 110:
Starting Up After Shutdown 93 Chapt
Page 111 and 112:
Managing the Controller 95 Chapter
Page 113 and 114:
Page 115 and 116:
Managing Enclosures 99 Chapter 4: M
Page 117 and 118:
101 Chapter 4: Management with WebP
Page 119 and 120:
Reconditioning a Battery 103 Chapte
Page 121 and 122:
Managing Physical Drives 105 Chapte
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Managing UPS Units 111 Chapter 4: M
Page 129 and 130:
Viewing UPS Information 113 Chapter
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Creating a Logical Drive 121 Chapte
Page 139 and 140:
Page 141 and 142:
To start Media Patrol: 1. Click the
Page 143 and 144:
Managing Logical Drives 127 Chapter
Page 145 and 146:
Viewing Logical Drive Statistics To
Page 147 and 148:
Page 149 and 150:
Managing Spare Drives 133 Chapter 4
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Chapter 5: Management with the CLU
Page 157 and 158:
Making a Telnet Connection 141 Chap
Page 159 and 160:
143 Chapter 5: Management with the
Page 161 and 162:
Managing the Subsystem Subsystem Ma
Page 163 and 164:
Managing the Controller Controller
Page 165 and 166:
Figure 4. Controller Status LED Con
Page 167 and 168:
Locating a Power Supply 151 Chapter
Page 169 and 170:
Page 171 and 172:
Managing Physical Drives Physical D
Page 173 and 174:
Page 175 and 176:
Creating a Disk Array - Automatic 1
Page 177 and 178:
Creating a Disk Array - Advanced 16
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Managing Spare Drives Spare Drive M
Page 187 and 188:
Deleting a Spare Drive 171 Chapter
Page 189 and 190:
Page 191 and 192:
Managing the Network Connection 175
Page 193 and 194:
Managing iSCSI Connections 177 Chap
Page 195 and 196:
Page 197 and 198:
• 181 Chapter 5: Management with
Page 199 and 200:
Deleting CHAPs 183 Chapter 5: Manag
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Making UPS Settings 191 Chapter 5:
Page 209 and 210:
Managing Users 193 Chapter 5: Manag
Page 211 and 212:
6. Press Ctrl-A to save the setting
Page 213 and 214:
Making SLP Settings 197 Chapter 5:
Page 215 and 216:
6. Press Ctrl-A to save your settin
Page 217 and 218:
Page 219 and 220:
Restoring Factory Defaults 203 Chap
Page 221 and 222:
Page 223 and 224:
Restarting the Subsystem 207 Chapte
Page 225 and 226:
Making Buzzer Settings 209 Chapter
Page 227 and 228:
Chapter 6: Management with the LCD
Page 229 and 230:
Advanced Mode 213 Perusing the Inte
Page 231 and 232:
Automatic IP Settings 215 Managing
Page 233 and 234:
Managing Enclosures 217 Managing En
Page 235 and 236:
219 Managing Disk Arrays 6. Press t
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
227 Managing Disk Arrays You must d
Page 245 and 246:
229 Managing Spare Drives 2. Press
Page 247 and 248:
Chapter 7: Maintenance This chapter
Page 249 and 250:
233 Chapter 7: Maintenance 6. Enter
Page 251 and 252:
Restarting Subsystem over a Telnet
Page 253 and 254: Replacing a RAID Controller 237 Cha
Page 255 and 256: Figure 3. RAID Controller cover and
Page 257 and 258: 241 Chapter 7: Maintenance 4. Lay t
Page 259 and 260: Figure 9. RAID Controller memory mo
Page 261 and 262: Chapter 8: Technology Background Th
Page 263 and 264: RAID 1 - Mirror 247 Chapter 8: Tech
Page 265 and 266: RAID 5 - Block and Parity Stripe 24
Page 267 and 268: RAID 10 - Mirror / Stripe 251 Chapt
Page 269 and 270: RAID 50 Axles 253 Chapter 8: Techno
Page 271 and 272: RAID 60 Axles 255 Chapter 8: Techno
Page 273 and 274: RAID 1E Recommended Applications fo
Page 275 and 276: Choosing Stripe Size 259 Chapter 8:
Page 277 and 278: Read Cache Policy 261 Chapter 8: Te
Page 279 and 280: 263 Chapter 8: Technology Backgroun
Page 281 and 282: RAID 0 265 Chapter 8: Technology Ba
Page 283 and 284: RAID 5 267 Chapter 8: Technology Ba
Page 285 and 286: RAID 50 269 Chapter 8: Technology B
Page 289 and 290: Transition 273 Chapter 8: Technolog
Page 293 and 294: Chapter 9: Troubleshooting This cha
Page 295 and 296: LEDs 279 Chapter 9: Troubleshooting
Page 297 and 298: Figure 5. VessRAID Controller LEDs
Page 299 and 300: 283 Chapter 9: Troubleshooting To d
Page 301 and 302: 285 Chapter 9: Troubleshooting To s
Page 303: LCD Panel Reports a Problem 287 Cha
Page 307 and 308: Reported Event Corrective Action 29
Page 309 and 310: Reported Event Corrective Action Ho
Page 313 and 314: Reported Event Corrective Action Ph
Page 317 and 318: Reported Event Corrective Action Sy
Page 319 and 320: • The Disk Status LED changes fro
Page 321 and 322: Incomplete Array 305 Chapter 9: Tro
Page 323 and 324: 307 Chapter 9: Troubleshooting You
Page 325 and 326: Enclosure 309 Chapter 9: Troublesho
Page 327 and 328: Connection Problems 311 Chapter 9:
Page 329 and 330: Figure 18.iSCSI port connection Lin
Page 331 and 332: 315 Chapter 9: Troubleshooting The
Page 333 and 334: Chapter 10: Support • Frequently
Page 335 and 336: How can I be sure everything is wor
Page 337 and 338: Italy Taiwan E-mail Support e-Suppo
Page 339 and 340: Limited Warranty 323 Chapter 10: Su
Page 341 and 342: Returning the Product For Repair 32
Page 343 and 344: Index Numerics 10GB Truncate 97, 14
Page 345 and 346: disk array, cont. status critical 1
Page 347 and 348: K KCC statement 8 L LCD panel advan
Page 349 and 350: N Netsend event reporting to Window
Page 351 and 352: eleasing lock 61, 146 renewing lock
Page 353 and 354: T Table Rounding 97, 148, 262 Techn
show all

VessRAID Setup - Promise Technology, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?