manuale per l'installatore - 1/3 tipologie d'installazione - 2/3 software ...

More documents

Recommendations

Info

INDICE INTRODUCTION WHAT IS THE PROGRAM FOR SEQUENT INSTALLERS TO WHOM IS THIS GUIDE ADDRESSED USEFUL REFERENCES 1. WHAT DO YOU NEED TO START 1.1 THE PERSONAL COMPUTER 1.2 THE INTERFACE CABLE FOR SEQUENT INSTALLATIONS 1.3 SOFTWARE AND HARDWARE KEY 2. SOFTWARE INSTALLATION AND HARDWARE KEY USE 2.1 “SEQUENT” SOFTWARE INSTALLATION ON PC WITH CDROM 2.2 “SEQUENT” SOFTWARE INSTALLATION ON PC WITH DISKETTES 3. STARTING OF THE PROGRAM AND ITS STRUCTURE 3.1 OPENING PAGE DESCRIPTION 3.2 MAIN KEYS 3.2.1 “PROGRAMMING” KEY 3.2.2 “SETTING UP” KEY 3.2.3 “DIAGNOSTIC” KEY 3.2.4 “UTILITY” KEY 4. PROGRAMMING 4.1 PROGRAMMING FILES TYPE 4.1.1 S19 FILE 4.1.2 FSF FILE 4.1.3 AAP FILE 4.2 ECU PROGRAMMING 4.2.1 PERSONALISED AIDED PROGRAMMING 4.2.1.1 Type of installation 4.2.1.2 Installation and injectors Calibration 4.2.1.3 Tem<strong>per</strong>ature sensors Calibration (only for CNG) 4.2.1.4 Rpm calibration 4.2.1.5 TPS Calibration 4.2.1.6 Oxygen Sensor Calibration 4.2.1.7 FSF file Saving 4.2.1.8 Self-mapping 2
5. SETTING UP 4.2.1.8.1 PETROL MAP 4.2.1.8.2 GAS SELF-MAPPING 4.2.1.9 Parameters transfer to the ECU 4.2.2 PROGRAMMING “FROM RECORDS” 5.1 PREVIOUSLY DESCRIBED FUNCTIONS 5.2 TYPE OF INSTALLATION 5.3 LEVEL CALIBRATION 5.4 P1-MAP 5.4.1 CALIBRATION MAP THROUGH P1 5.4.2 MAP CALIBRATION THROUGH EXTERNAL PRESSURE GAUGE 5.5 CHANGE-OVER 5.6 TIP IN AND TIP OUT 5.7 SELF-LEARNING 6. DIAGNOSTIC 6.1 DATA DISPLAY 6.1.1 STORAGE PARAMETERS 6.1.2 BEGINNING/RECORD RESTARTING 6.1.3 GRAPHS BLOCKING 6.1.4 SETTING 6.1.5 PAGE EXIT 6.2 ACTUATORS TEST 6.3 ECU VERSION 6.3.1 PARAMETERS DESCRIPTION 7. UTILITY 7.1 LANGUAGE CHOICE 7.2 COMMUNICATION 7.3 ELECTRICAL PLANS 6.3.1.1 ECU Code 6.3.1.2 Loader version 6.3.1.3 Software version 6.3.1.4 Map version 6.3.1.5 Vehicle code 6.3.1.6 Calibrations Version 6.3.1.7 First programming date 6.3.1.8 Programming code 3
Page 1: TA010976B - N. 4 del 11.11.2002 M.T
Page 5 and 6: INTRODUCTION WHAT IS THE PROGRAM FO
Page 7 and 8: 1. WHAT DO YOU NEED TO START? Brief
Page 9 and 10: 2. SOFTWARE INSTALLATION AND HARDWA
Page 11 and 12: 3. STARTING OF THE PROGRAM AND ITS
Page 13 and 14: main function. To better understand
Page 15 and 16: screen. There are two types of prog
Page 17 and 18: need to install two (refer to insta
Page 19 and 20: 3. Click on the Acquire key to memo
Page 21 and 22: If the automatic procedure took a k
Page 23 and 24: 4.2.1.7 FSF file Saving This is the
Page 25 and 26: 3.Second gas map Only the first fil
Page 27 and 28: Achieving the stationary conditions
Page 29 and 30: ation points. These latter, represe
Page 31 and 32: • Anytime it is possible to stop
Page 33 and 34: The tick marks the files which will
Page 35 and 36: BE CAREFUL!: • If the loader prog
Page 37 and 38: • TPS Calibration. • Oxygen sen
Page 39 and 40: then click on EXIT to continue. If
Page 41 and 42: following steps (picture 5.10): 1.T
Page 43 and 44: 5.5 CHANGE-OVER This screen allows
Page 45 and 46: ehaviour. 1000 corresponds to use a
Page 47 and 48: %Error value. A map can be consider
Page 49 and 50: At the top of the graphs and the nu
Page 51 and 52: 6.1.5 PAGE EXIT Use the sixth key f
Page 53 and 54:
6.3 ECU VERSION With DIAGNOSTIC key
Page 55 and 56:
sion speed. If there are not partic
Page 57 and 58:
the key contact. 7. Select “LPG
Page 59 and 60:
ated with the same name it has when
Page 61 and 62:
If necessary, after the DOWN- LOAD,
show all

manuale per l'installatore - 1/3 tipologie d'installazione - 2/3 software ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?