Problem Determination and Service Guide - Public Support Login ...

More documents

Recommendations

Info

Introduction Table 3–2. Memory-card LEDs <strong>and</strong> button LED Description Light path diagnostics button power LED When this LED is lit, it indicates that the capacitor is charged <strong>and</strong> is able to light other LEDs. Light path diagnostics button Push this button to relight the error LED that had previously been lit. Memory card/DIMM error LED When this LED is lit, it indicates that an error has occurred in one of the DIMMs on the memory card or that there is a problem with the memory card. Memory card only error LED When this LED is lit, it indicates that an error has occurred on the memory card itself. DIMMs 1 - 8 error LEDs When one of these LEDs is lit, it indicates that an error has occurred in the associated DIMM. 3–16 3850 7281–000
Memory-card connectors on the microprocessor board The following illustration shows the memory-card connectors on the microprocessor board. Microprocessor-board connectors The following illustration shows the connectors on the microprocessor board. Introduction 3850 7281–000 3–17
Page 1 and 2: EnterpriseServer ES7000Model7600RG2
Page 3 and 4: Contents Section 1. Safety Section
Page 5 and 6: Section 5. Parts listing Replaceabl
Page 7 and 8: Appendix A. Services and Support Ap
Page 9 and 10: Tables 3-1. Power-supply LEDs . . .
Page 11 and 12: Section 1 Safety Before installing
Page 13 and 14: 3. Check the power cord: • Make s
Page 15 and 16: DANGER Statement 2: Electrical curr
Page 17 and 18: CAUTION: Statement 5: Use safe prac
Page 19 and 20: Section 2 Start here You can solve
Page 21 and 22: Many configuration problems are cau
Page 23 and 24: Section 3 Introduction This Problem
Page 25 and 26: Notes: • Racks are marked in vert
Page 27 and 28: • Serial-attached SCSI (SAS) cont
Page 29 and 30: Electrostatic-discharge connector:
Page 31 and 32: Notes: Rear view • For optimum fa
Page 33 and 34: AC power LED: Each hot-swap power s
Page 35 and 36: Power-supply LEDs AC DC Error On Of
Page 37: The server can be turned off in any
Page 41 and 42: The following table describes the f
Page 43 and 44: The following table describes the f
Page 45 and 46: Introduction 3850 7281-000 3-23
Page 47 and 48: Section 4 Diagnostics This chapter
Page 49 and 50: • DSA log: This log is generated
Page 51 and 52: Error code Description Action 00100
Page 61 and 62: Troubleshooting tables Use the trou
Page 63 and 64: • If an action step is preceded b
Page 65 and 66: USB keyboard, mouse, or pointing-de
Page 67 and 68: Symptom Action The amount of system
Page 69 and 70: • Follow the suggested actions in
Page 71 and 72: Symptom Action The monitor has scre
Page 73 and 74: performed only by a trained service
Page 75 and 76: Serial-device problems • Follow t
Page 77 and 78: Video problems See Monitor or video
Page 79 and 80: Notes: • You must remove the memo
Page 81 and 82: Remind button The following illustr
Page 83 and 84: Lit light path diagnostics LED with
Page 89 and 90:
The following illustration shows th
Page 91 and 92:
• System configuration • Vital
Page 93 and 94:
000 The server passed the test. Do
Page 95 and 96:
Table 4-2. DSA messages (cont.) Mes
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Error Error messages might require
Page 179 and 180:
Table 4-3. Integrated management mo
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Damaged data in CMOS memory or dama
Page 215 and 216:
Section 5 Parts listing The followi
Page 217 and 218:
Replaceable server components Repla
Page 219 and 220:
Index Description Table 5-1. Parts
Page 221 and 222:
For units intended to be operated a
Page 223 and 224:
Section 6 Removing and replacing se
Page 225 and 226:
System reliability guidelines To he
Page 227 and 228:
Removing and replacing server compo
Page 229 and 230:
You can install one or more optiona
Page 231 and 232:
4. Slide the top cover forward and
Page 233 and 234:
Removing an adapter Removing and re
Page 235 and 236:
6. Remove the battery: a. Use one f
Page 237 and 238:
6. Start the Setup utility and rese
Page 239 and 240:
1. Read the safety information in S
Page 241 and 242:
3. Open the fan-release handle by p
Page 243 and 244:
Removing a hot-swap hard disk drive
Page 245 and 246:
Caution Never remove the cover on a
Page 247 and 248:
Removing a QPI wrap card To remove
Page 249 and 250:
Memory cards and memory modules (DI
Page 251 and 252:
• The following illustration show
Page 253 and 254:
Table 6-3. High-performance memory-
Page 255 and 256:
Memory card/DIMM error LED: When th
Page 257 and 258:
Replacing the memory card To instal
Page 259 and 260:
Removing and replacing FRUs FRUs mu
Page 261 and 262:
6. Remove the memory cards and memo
Page 263 and 264:
Replacing the I/O-board shuttle To
Page 265 and 266:
13. Remove the cables from the serv
Page 267 and 268:
Removing and replacing server compo
Page 269 and 270:
4. Slide the RAID adapter carrier a
Page 271 and 272:
4. Connect the cables and power cor
Page 273 and 274:
4. Slide the hard disk drive backpl
Page 275 and 276:
To remove a microprocessor and heat
Page 277 and 278:
9. Place the microprocessor install
Page 279 and 280:
3. Install the replacement micropro
Page 281 and 282:
c. Position the heat sink above the
Page 283 and 284:
1. Read the safety information in S
Page 285 and 286:
17. Using the Advanced Settings Uti
Page 287 and 288:
Section 7 Configuration information
Page 289 and 290:
For information about using this pr
Page 291 and 292:
o Commands on USB Interface Prefere
Page 293 and 294:
Passwords - Clear Administrator Pas
Page 295 and 296:
1. Turn off the server. 2. Restart
Page 297 and 298:
3. Select System Settings → Integ
Page 299 and 300:
Advanced Settings Utility program C
Page 301 and 302:
Appendix A Services and Support Thi
Page 303 and 304:
Service Task Responsibility Billabl
Page 305 and 306:
Appendix B Notices Important notes
Page 307 and 308:
For the European Union: Notice: Thi
Page 309 and 310:
European Union EMC Directive confor
Page 311 and 312:
Russia Electromagnetic Interference
Page 313 and 314:
Index A ABR, automatic boot failure
Page 315 and 316:
optional devices, 4-26 pointing dev
Page 317 and 318:
power-on, 3-11 rear, 3-11 front, 3-
Page 319 and 320:
hard disk drive, 6-21 heat sink, 6-
Page 322:
© Portions copyright Unisys Corpor
show all

Problem Determination and Service Guide - Public Support Login ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?