User's Manual AXF Magnetic Flowmeter Integral ... - Yokogawa

More documents

Recommendations

Info

6. OUTLINE Gasket: Joints: Use Lining General-Purpose Use / Submersible Type / Explosion proof Type PFA/Polyurethane Rubber/ Natural Soft Rubber/ EPDM Rubber grounding ring grounding ring Ceramics Lining Standard Ceramics Union Joints (size 10 mm or less) weld joint (GUW) screw joint (GUN, GUR) nut Gasket within Flowtube Standard Materials for Union Joint No gasket within Flowtube Gasket within Flowtube Gasket Material (within Flowtube) Fluororesin with — ceramic fillers (Valqua #7020) Process Connection Code GUW: Union Joint (weld joint) Process Connection Code GUN, GUR: union joint (screw joint) Stainless steel (JIS SUS316L (ANSI 316L SS/EN 1.4404 equivalent)) grounding ring grounding ring Note: Contact Yokogawa office if PVC union joint is required. T23-3.EPS Optional code (GA, GC, GD, or GF) Only when selecting the PFA lining/ ceramics lining Gasket within Flowtube Gasket within Flowtube Gasket Material (within Flowtube) GA: Fluororubber for PVC pipes (Viton®) GC: Acid-resistant fluororubber for PVC pipes (Viton®) GD: Alkali-resistant fluororubber for PVC pipes (Viton®) GF* 1 : Fluororesin with alkali-resistant carbons for metal pipes *1: GF is applicable only for ceramics lining. grounding ring Use Standard Adapter for clamp connection Adapter for union connection Adapter for butt weld connection Sanitary Type Materials for Adapters (clamp, union, butt weld) Stainless steel-JIS SUS316L (AISI 316L SS/EN 1.4404 equivalent) Optional code (BCF, BSF, BCC, or BSC) Use Lining Standard Flange of user’s pipe Gasket for user’s flange Gasket Material (for user’s flange) BCF, BSF: PTFE-sheathed non-asbestos BCC, BSC: Chloroprene rubber Adapter for clamp connection Adapter for union connection Sanitary Type PFA T23-1.EPS O-Ring (Replaceable electrode type only): Fluororubber (Part number : G9303SE) T23-4.EPS Electrode Construction: Non-replaceable Electrode Type General-Purpose Use/Submersible Type/Explosion proof Type: PFA, Polyurethane Rubber lining: External insertion type Natural Soft Rubber, EPDM Rubber lining: Internal insertion type Ceramics lining: Integral type Sanitary Type: Internal insertion type Adapter for butt weld connection Gasket within Flowtube Gasket Material (within Flowtube) EPDM (ethylene propylene) rubber Optional code (GH) GH: Silicone rubber T23-2.EPS 6-8 IM 01E20D01-01E
6. OUTLINE Replaceable Electrode Type Electrode parts can be put into unit to facilitate replacement or mounting at customer site. The optional dedicated tool (F9807SK) is required. Replaceable electrodes are available for the following: AXF standard: Use General- Purpose Use Process Connection Wafer Flange Available Size 25 to 300 mm (1.0 to 12 in.) 25 to 400 mm (1.0 to 16 in.) Lining PFA/ Polyurethane Rubber Electrode Material JIS SUS316L (AISI 316L SS/EN 1.4404 equivalent) ( * 1) T06.EPS Replacement model for earlier ADMAG or ADMAG AE: Use General- Purpose Use Process Connection Flange Available Size 150 to 250 mm (6.0 to 10 in.) Lining PFA/ Polyurethane Rubber Electrode Material JIS SUS316L (AISI 316L SS/EN 1.4404 equivalent) ( * 1) T07.EPS *1: If any other electrode materials are required, please contact Yokogawa office. Mounting/Shapes (Remote Flowtube): • Electrical Connection: ANSI 1/2 NPT female ISO M20 1.5 female JIS G1/2 (PF1/2) female • Direction of Electrical Connection: The direction can be changed even after delivery. Note: In case of submersible types, an optional code DHC, and sizes of 1100 mm or larger, the direction can not be changed after delivery. • Terminal Connection at Terminal Box: M4 size screw Grounding: Grounding resistance 100 Ω or less * In case of explosion proof type except TIIS, follow the domestic electrical requirements as regulated in each country. * In case of TIIS Flameproof type, refer to description of “HAZARDOUS AREA CLASSIFCATION”. Combined Converter: •A remote flowtube for sizes of up to 400 mm can be combined with the AXFA11 Converter or the AXFA14 Converter. If a combined converter is changed from AXFA11 to AXFA14 or vice versa, a new meter factor must be adjusted by flow calibrations. • In case that size 250 mm (10 in.) or larger is used in low conductivity or high concentration slurries, please use the AXFA11 Converter. •A remote flowtube for sizes of 500 mm or larger can be combined with the AXFA11 Converter only. • Maximum Cable Length: Combination of AXF remote Flowtube and AXFA11: up to 200 m (660 ft) Combination of AXF remote Flowtube and AXFA14: up to 100 m (330 ft) ■ HAZARDOUS AREA CLASSIFICATION FM: *AXF002C – AXF400C Applicable Standard: FM3600, FM3610, FM3615, FM3810, ANSI/NEMA 250 (Integral Flowmeter) Explosion proof for Class I, Division 1, Groups A, B, C & D. Dust-ignition proof for Class II/III, Division1, Groups E, F & G. Intrinsically safe (electrodes) for Class I, Division 1, Groups A, B, C & D. “SEAL ALL CONDUITS WITHIN 18 INCHES” “WHEN INSTALLED IN DIV. 2, SEALS NOT REQUIRED” Electrode Circuit Um: 250 Vac/dc Maximum power supply voltage: 250 Vac/130 Vdc Excitation Circuit: 140V max Enclosure: NEMA 4X Temperature Code: T6 Refer to following table; Temperature Code T6 T5 T4 T3 Maximum Process Temperature +70°C (+158°F) +85°C (+185°F) +120°C (+248°F) +130°C (+266°F) Minimum Process Temperature –40°C (–40°F) –40°C (–40°F) –40°C (–40°F) –40°C (–40°F) Ambient Temp.: –40°C to +60°C (–40°F to +140°F) T27-1_1.EPS (Remote Flowtube) Explosion proof for Class I, Division 1, Groups A, B, C & D. Dust-ignition proof for Class II/III, Division1, Groups E, F & G. Intrinsically safe (electrodes) for Class I, Division 1, Groups A, B, C & D. “SEAL ALL CONDUITS WITHIN 18 INCHES” “WHEN INSTALLED IN DIV. 2, SEALS NOT REQUIRED” Electrode Circuit Um: 250 Vac/dc Excitation Circuit: 170V max Enclosure: NEMA 4X Temperature Code: T6 Refer to following table; Temperature Code T6 T5 T4 T3 Maximum Process Temperature +70°C (+158°F) +85°C (+185°F) +120°C (+248°F) +150°C (+302°F) Minimum Process Temperature –40°C (–40°F) –40°C (–40°F) –40°C (–40°F) –40°C (–40°F) Ambient Temp.: –40°C to +60°C (–40°F to +140°F) Note: Installation shall be in accordance with the manufacturer’s instructions and National Electric code, ANSI/NFPA-70. T28-1_1.EPS 6-9 IM 01E20D01-01E
Page 1 and 2:
User's Manual AXF Magnetic Flowmete
Page 3 and 4:
CONTENTS 5.2 Removing, Cleaning, an
Page 5 and 6:
1. INTRODUCTION IMPORTANT An IMPORT
Page 7 and 8:
1.4 ATEX Documentation This procedu
Page 9 and 10:
2.3 Storage Precautions If the inst
Page 11 and 12:
(Incorrect) Upstream side (Correct)
Page 13 and 14:
3. INSTALLATION (4) Terminal Box Co
Page 15 and 16:
3. INSTALLATION Table 3.3.3 Tighten
Page 17 and 18:
3. INSTALLATION *Nut (eight units)
Page 19 and 20: 3. INSTALLATION 3.3.3 Nominal Diame
Page 21 and 22: 3. INSTALLATION Table 3.3.8 Wafer T
Page 23 and 24: 3. INSTALLATION Table 3.3.12 Center
Page 25 and 26: 3. INSTALLATION Table 3.3.14 Flange
Page 27 and 28: 3. INSTALLATION Table 3.3.16 Flange
Page 29 and 30: 3. INSTALLATION Table 3.3.17 Instal
Page 31 and 32: 3. INSTALLATION 3.3.6 Sanitary Type
Page 33 and 34: 3. INSTALLATION CAUTION • In case
Page 35 and 36: 4. WIRING NOTE • For power cables
Page 37 and 38: - - I - 4. WIRING conforming to IEC
Page 39 and 40: 4. WIRING Connect the AXF integral
Page 41 and 42: 4.2 Wiring the Remote Flowtube This
Page 43 and 44: 4. WIRING NOTE • For excitation c
Page 45 and 46: 4. WIRING Terminal Symbols A B C EX
Page 47 and 48: 4. WIRING (5) Wiring the Remote Flo
Page 49 and 50: 5. MAINTENANCE 5. MAINTENANCE WARNI
Page 51 and 52: 5. MAINTENANCE (6) Move aside the e
Page 53 and 54: 5. MAINTENANCE NOTE Always hold dow
Page 55 and 56: 5. MAINTENANCE 5.4 Components Repla
Page 57 and 58: (2) Replace the assembly by pushing
Page 59 and 60: 5. MAINTENANCE Coil Circuit Checkin
Page 61 and 62: 5. MAINTENANCE 5.8.2 Unstable Zero
Page 63 and 64: 6. OUTLINE 6. OUTLINE ■ STANDARD
Page 65 and 66: 6. OUTLINE Flowtubes (Remote Flowt
Page 67 and 68: 6. OUTLINE Size of AXF Flowtubes: R
Page 69: 6. OUTLINE Size 150 mm (6.0 in.) to
Page 73 and 74: 6. OUTLINE CSA: *AXF002C - AXF400C
Page 75 and 76: 6. OUTLINE TIIS: Certificate: Size:
Page 77 and 78: 6. OUTLINE CAUTION *1: When perform
Page 79 and 80: 6. OUTLINE Size (in.) English Units
Page 81 and 82: 6. OUTLINE Natural Soft Rubber Lini
Page 83 and 84: 6. OUTLINE ■ MODEL AND SUFFIX COD
Page 85 and 86: 6. OUTLINE AXF STANDARD (Flange Typ
Page 87 and 88: 6. OUTLINE AXF STANDARD (Clamp/Unio
Page 89 and 90: REPLACEMENT MODEL FOR EARLIER ADMAG
Page 91 and 92: 6. OUTLINE Table of Optional Speci
Page 97 and 98: 6. OUTLINE AXF Standard, AXF150-AX
Page 99 and 100: 6. OUTLINE AXF Standard, AXF150, A
Page 103 and 104: (ød) 6. OUTLINE AXF Standard, AXF
Page 109 and 110: 6. OUTLINE Replacement model for E
Page 111 and 112: AXF Standard, AXF500-AXF10L, JIS/AN
Page 113 and 114: 6. OUTLINE AXF Standard, AXF16L-AX
Page 115 and 116: 7. PED (PRESSURE EQUIPMENT DIRECTIV
Page 117 and 118: 8. EXPLOSION PROTECTED TYPE INSTRUM
Page 119 and 120: 8.2 FM (1) Technical Data *AXF002C
Page 121 and 122:
8. EXPLOSION PROTECTED TYPE INSTRUM
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
INSTALLATION AND OPERATING PRECAUTI
Page 129:
REVISION RECORD Title: AXF Magnetic
show all

User's Manual AXF Magnetic Flowmeter Integral ... - Yokogawa

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?