BaseStation 3200 User Manual â 11.7.5.15 ... - Baseline Systems

More documents

Recommendations

Info

BaseStation 3200 Advanced Irrigation Controller Manual Configuring Other Devices Assigning Soil Moisture Sensors (biSensors) to Primary Zones When you have biSensors connected to your irrigation system, you need to assign each sensor to the zone where it is located. This zone then becomes a primary zone. 1. If you have not searched for the biSensors, do that first. Refer to Searching for biSensors on page 37. 2. With the dial in the biSensor Menu position and the biSensor List displayed, press the + or – button to select any unassigned biSensor serial number. 3. Press the NEXT or PREV button to select the zone, and then press the ENTR button. 4. Repeat for each primary zone with a biSensor. Note: When a soil moisture biSensor is assigned, it is initially set for the Lower Limit water strategy. To configure your biSensors for watering, refer to Setting Up Soil Moisture Sensor Based Watering on page 51. Configuring Pause Devices You can configure and use up to seven pause devices with the BaseStation 3200. Pause devices are automatically assigned a number from one to seven when they are found during a search operation. 1. If you have not searched for the pause biCoders, do that first. Refer to Searching for Pause biCoders and Temperature Sensors on page 37. 2. Turn the dial to the AUX position. 3. Press the NEXT button to move to Temp/Pause, and then press the ENTR button. 4. If you have multiple pause biCoders attached to your controller, make sure that the one you want to configure is displayed in the field in the top left of the screen. If you need to select a different pause biCoder, press the + or – button until the pause biCoder that you want to configure is displayed in the field. 5. Press the NEXT button to move to the Pause Delay Time field. 6. Press the + or – button to change the time. You can set the Pause Delay Time in hour increments between zero and 24 hours. When the pause biCoder detects that its contacts have been opened, the specified programs will pause and suspend all watering. The controller waits for the specified pause delay time, and then it checks the pause biCoder again. If the contacts are still open, it waits again for the pause delay time, but if the contacts are closed, the paused programs will resume watering. 7. Press the NEXT button to move to the list of programs, and then press the NEXT or PREV button to select the program that you want change. Page 40
BaseStation 3200 Advanced Irrigation Controller Manual 8. When the program is selected, press the + or – button to change between Y (yes) and – (no). Note: If you want to turn off the pause biCoder, select the Pause Delay Time field, and then press the CLR button. 9. When you have finished making changes, turn the dial to the Auto Run position. Configuring Flow biCoders, Flow Meters, and Flow Sensors Flow Meters and Flow Sensors are configured on the Flow Menu dial position. Refer to Configuring a Flow Device on page 57 for detailed instructions for assigning and configuring Flow biCoders, Flow Meters, and/or Flow Sensors. Configuring a Master Valve/Pump Start biCoder 1. If you have not searched for the biCoders, do that first. Refer to Searching for biCoders (including Powered biCoders) on page 36. 2. With the dial in the biCoder Menu position and the biCoder List displayed, press the + or – button to select the Master Valve /Pump Start biCoder that you wish to configure. 3. Press the NEXT or PREV button to select the Master Valve Zone you would like to configure. 4. Press the ENTR button. Note: You can configure a single, dual, or pump start biCoder as a master valve. 5. When you have finished making changes, turn the dial to the Auto Run position. Associating a Master Valve/Pump Start biCoder with Programs 1. If you have not configured the biCoders with the master valves, do that first. Refer to Configuring a Master Valve/Pump Start biCoder on page 41. 2. Turn the dial to the MV/Pump Start position. 3. Press the + or – button to select the Master Valve /Pump Start that you want to turn on when a specified program runs. 4. Press the NEXT or PREV button to move to the list of programs, and then press the NEXT or PREV button to select the program that you want change. 5. When the program is selected, press the + or – button to change between Y (yes) and – (no). Note: You can associate a master valve with one or all programs. 6. When you have finished making changes, turn the dial to the Auto Run position. Page 41
Page 1 and 2: BaseStation 3200 Advanced Irrigatio
Page 3 and 4: Table of Contents 1 - INTRODUCTION
Page 5 and 6: 6 - INITIAL PROGRAMMING ...........
Page 7 and 8: Troubleshooting the Two-Wire: High
Page 47: BaseStation 3200 Advanced Irrigatio
Page 99 and 100:
BaseStation 3200 Advanced Irrigatio
Page 101 and 102:
BaseStation 3200 Advanced Irrigatio
show all

BaseStation 3200 User Manual â 11.7.5.15 ... - Baseline Systems

Create successful ePaper yourself

Delete template?

Save as template?

BaseStation 3200 User Manual â 11.7.5.15 ... - Baseline Systems