tainy hmod-v3-io, tainy hmod-l3-io - Dr. Neuhaus ...

More documents

Recommendations

Info

Setup 2.2 Preconditions for operation In order to operate the TAINY xMOD, the following information must be on hand and the following preconditions must be fulfilled: Antenna An antenna, adapted to the frequency bands of the GSM network operator you have chosen: 850 MHz, 900 MHz, 1800 MHz or 1900 MHz. Please use only antennas from the accessories for the TAINY xMOD, because they are tested to operate together with the TAINY xMOD. See Chapter 2.6. Power supply A power supply with a voltage between 12 VDC and 60 VDC that can provide sufficient current. See Chapter 2.6. SIM card A SIM card from the chosen GSM network operator. PIN The PIN for the SIM card HSPA+ / UMTS EGPRS / GPRS activation CSD 9600 bit/s activation The services HSPA+, UMTS data (only TAINY HMOD) and / or EGPRS or GPRS must be enabled on the SIM card by your mobile communications network provider. The access data must be known: � Access Point Name (APN) � User name � Password The SIM card must be activated by your GSM network operator for the CSD service if you wish to use remote configuration via a dial-in data connection, see Chapter 8.3. Page 16 of 111 TAINY xMOD
2.3 Overview 2.4 Service button Setup TAINY xMOD Page 17 of 111 A – Connection terminals for the power supply B – Service button C – Antenna jack 1, type SMA D – Operating state indicators S, Q, C E - Antenna jack 2, type SMA (only TAINY HMOD-x3-IO) F – Service (USB) – Reserviert für spätere Anwendungen G – Connection terminals for the gate inputs and outputs H – LAN0 / 10/100-Base-T RJ45 jack for connecting the local network with integrated indicator lamps I – LAN1 / 10/100-Base-T RJ45 jack for connecting the local network with integrated indicator lamps K – Operating state indicators POWER, IN, OUT VPN (only TAINY xMOD-V3-IO) On the front side of the TAINY xMOD there is a small hole (see B) which has a button behind it. Use a pointed object, e.g. a straightened-out paperclip, to press this button. � If you press the button for longer than 5 seconds, the TAINY xMOD reboots and loads the factory settings.
Page 1 and 2: User Manual TAINY HMOD-V3-IO, TAINY
Page 3 and 4: Products ! Safety instructions The
Page 5 and 6: Firmware with open source GPL/LGPL
Page 7 and 8: Contents Contents 1 Introduction ..
Page 9 and 10: 1 Introduction Introduction Product
Page 11 and 12: Introduction Local applications cou
Page 13 and 14: Terms Here are definitions of terms
Page 15: 2 Setup 2.1 Step by step Set up the
Page 19 and 20: TAINY EMOD Lamp Status Meaning S (S
Page 21 and 22: 2.6 Connections LAN0, LAN1 (10/100
Page 23 and 24: 24V / 0V power supply The TAINY xMO
Page 25 and 26: 3 Configuration 3.1 Overview Remote
Page 27 and 28: Preferred DNS server Configuration
Page 29 and 30: The start page is not displayed If
Page 31 and 32: Signal (CSQ Level) Indicates the st
Page 33 and 34: Carrying out configuration ONLY TAI
Page 35 and 36: Function Access to the TAINY xMOD i
Page 37 and 38: 4 Local interface 4.1 IP addresses
Page 39 and 40: 4.3 DNS to local network Local Netw
Page 41 and 42: Poll interval Serve system time to
Page 43 and 44: Provider selection mode - Manual Pr
Page 45 and 46: Provider selection mode - Automatic
Page 47 and 48: Activity on faulty connection Renew
Page 49 and 50: Remote host 0.0.0.0 Group group Use
Page 51 and 52: 5.7 Volume supervision External net
Page 53 and 54: Security functions Protocol Select
Page 55 and 56: 6.2 Port Forwarding Security > Port
Page 57 and 58: 6.4 Firewall Log Security > Firewal
Page 59 and 60: Requirements for the remote network
Page 61 and 62: VPN connections CA certificate The
Page 63 and 64: VPN connections ISAKMP-SA mode Agre
Page 65 and 66: VPN Standard Mode Edit Settings Con
Page 67 and 68:
VPN connections Remote net address
Page 69 and 70:
VPN Standard Mode Edit IKE VPN conn
Page 71 and 72:
7.4 Loading VPN certificates IPsec
Page 73 and 74:
7.6 Supervision of VPN connections
Page 75 and 76:
Number of connect attempts until re
Page 77 and 78:
Action Define how access to the spe
Page 79 and 80:
Factory setting The factory setting
Page 81 and 82:
9 Status, log and diagnosis 9.1 Log
Page 83 and 84:
Status, log and diagnosis Function
Page 85 and 86:
Status, log and diagnosis Function
Page 87 and 88:
Additional functions Text Here ente
Page 89 and 90:
Port number 26864 Firewall Rules No
Page 91 and 92:
The following parameters of the TAI
Page 93 and 94:
Target host NONE Target port 162 Ta
Page 95 and 96:
Asymmetric encryption CIDR Small le
Page 97 and 98:
Small lexicon of routers CSQ / RSSI
Page 99 and 100:
Small lexicon of routers EGPRS EGPR
Page 101 and 102:
IPsec MIB See SNMP Small lexicon of
Page 103 and 104:
Protocol, Transfer protocol Small l
Page 105 and 106:
X.509 certificate A type of "seal"
Page 107 and 108:
Network B Computer B1 B2 B3 B4 Addi
Page 109 and 110:
Conformity CE Conforms to Directive
Page 111:
Protection class IP20 Dimensions 11
show all

tainy hmod-v3-io, tainy hmod-l3-io - Dr. Neuhaus ...

Create successful ePaper yourself

Delete template?

Save as template?