tainy hmod-v3-io, tainy hmod-l3-io - Dr. Neuhaus ...

More documents

Recommendations

Info

Status, log and diagnosis Download service snapshot Click on download. You can select the location on the Admin PC where the snapshot file will be saved. The filename of the snapshot file has the following structure: _Snapshot_.tgz, e.g.: tainyHMOD_Snapshot_200711252237.tgz Advanced diagnosis Please only Activate the Advanced diagnosis if asked to do so by our customer service. In operation with advanced diagnosis, information is written to the diagnosis logs much more often. Some additional information is also saved. This is useful for systematic troubleshooting. Note When advanced diagnosis is active, the frequent write access to the nonvolatile memory of the TAINY xMOD can lead to a reduction of its service life. Factory setting The factory settings for the TAINY xMOD are as follows: 9.4 Hardware information Maintenance > Hardware Info Advanced diagnosis Off (Activate) Function Shows important information for hardware identification. This information is often needed in the event of queries to our customer service. 9.5 Software information Maintenance > Software Info Page 84 of 111 TAINY xMOD
Status, log and diagnosis Function Shows important information for software identification. This information is often needed in the event of queries to our customer service. 9.6 Software Update Maintenance > Update Planned updates are also shown. See also Chapter 9.6 Function You can use the update function to load new operating software to the TAINY xMOD and activate this software. The new software is unpacked during an immediate update. This process can take a few minutes. Then the actual update process begins, which is indicated by a light up of the LEDs. The settings of the TAINY xMOD are adopted, if they still work in the new software version as they did before the update. Define the update time No Immediate update - The new operating software is activated immediately after you load it and click on the Send button. Select update file Yes Scheduled update - The new operating software is operated at a specified update time. For this purpose, the software must be loaded in advance. If you wish to specify the time for the update, enter the time at which the new software should be activated. Enter the year – month – day – hour – minute. The settings of the TAINY xMOD are adopted, if they still work in the new software version as they did before the update. Select the new operating software with Browse. For example, operating software for the TAINY xMOD has the following name: HMOD_V2IO_v1.107-v1.214.tgz Load the firmware to the device with Open. Send Send activates the operating software, either immediately or at the specified time. TAINY xMOD Page 85 of 111
Page 1 and 2:
User Manual TAINY HMOD-V3-IO, TAINY
Page 3 and 4:
Products ! Safety instructions The
Page 5 and 6:
Firmware with open source GPL/LGPL
Page 7 and 8:
Contents Contents 1 Introduction ..
Page 9 and 10:
1 Introduction Introduction Product
Page 11 and 12:
Introduction Local applications cou
Page 13 and 14:
Terms Here are definitions of terms
Page 15 and 16:
2 Setup 2.1 Step by step Set up the
Page 17 and 18:
2.3 Overview 2.4 Service button Set
Page 19 and 20:
TAINY EMOD Lamp Status Meaning S (S
Page 21 and 22:
2.6 Connections LAN0, LAN1 (10/100
Page 23 and 24:
24V / 0V power supply The TAINY xMO
Page 25 and 26:
3 Configuration 3.1 Overview Remote
Page 27 and 28:
Preferred DNS server Configuration
Page 29 and 30:
The start page is not displayed If
Page 31 and 32:
Signal (CSQ Level) Indicates the st
Page 33 and 34: Carrying out configuration ONLY TAI
Page 35 and 36: Function Access to the TAINY xMOD i
Page 37 and 38: 4 Local interface 4.1 IP addresses
Page 39 and 40: 4.3 DNS to local network Local Netw
Page 41 and 42: Poll interval Serve system time to
Page 43 and 44: Provider selection mode - Manual Pr
Page 45 and 46: Provider selection mode - Automatic
Page 47 and 48: Activity on faulty connection Renew
Page 49 and 50: Remote host 0.0.0.0 Group group Use
Page 51 and 52: 5.7 Volume supervision External net
Page 53 and 54: Security functions Protocol Select
Page 55 and 56: 6.2 Port Forwarding Security > Port
Page 57 and 58: 6.4 Firewall Log Security > Firewal
Page 59 and 60: Requirements for the remote network
Page 61 and 62: VPN connections CA certificate The
Page 63 and 64: VPN connections ISAKMP-SA mode Agre
Page 65 and 66: VPN Standard Mode Edit Settings Con
Page 67 and 68: VPN connections Remote net address
Page 69 and 70: VPN Standard Mode Edit IKE VPN conn
Page 71 and 72: 7.4 Loading VPN certificates IPsec
Page 73 and 74: 7.6 Supervision of VPN connections
Page 75 and 76: Number of connect attempts until re
Page 77 and 78: Action Define how access to the spe
Page 79 and 80: Factory setting The factory setting
Page 81 and 82: 9 Status, log and diagnosis 9.1 Log
Page 83: Status, log and diagnosis Function
Page 87 and 88: Additional functions Text Here ente
Page 89 and 90: Port number 26864 Firewall Rules No
Page 91 and 92: The following parameters of the TAI
Page 93 and 94: Target host NONE Target port 162 Ta
Page 95 and 96: Asymmetric encryption CIDR Small le
Page 97 and 98: Small lexicon of routers CSQ / RSSI
Page 99 and 100: Small lexicon of routers EGPRS EGPR
Page 101 and 102: IPsec MIB See SNMP Small lexicon of
Page 103 and 104: Protocol, Transfer protocol Small l
Page 105 and 106: X.509 certificate A type of "seal"
Page 107 and 108: Network B Computer B1 B2 B3 B4 Addi
Page 109 and 110: Conformity CE Conforms to Directive
Page 111: Protection class IP20 Dimensions 11
show all

tainy hmod-v3-io, tainy hmod-l3-io - Dr. Neuhaus ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?