tainy hmod-v3-io, tainy hmod-l3-io - Dr. Neuhaus ...

More documents

Recommendations

Info

SNMP 11.2 Alarm messages via SNMP traps SNMP – SNMP traps The TAINY xMOD sends messages in the form of SNMP traps for various events. Enable SNMP traps Select Yes if you want to activate the sending of SNMP traps. Select No if you want to switch off the sending of SNMP traps. Target host Enter the IP address of the SNMP trap recipient. Target port Enter the IP port of the SNMP trap recipient. Target name Enter the name of the SNMP trap recipient. Target community Enter the name of the SNMP community here. Send keepalive messages Device keepalive interval (minutes) Event: Warning level for monthly traffic volume reached Event: Maximum monthly traffic volume reached Event: Connection reestablished Event: Gate inout toggled Event: Configuration profile activated Select Yes if you want the TAINY xMOD keepalive packages to be sent as an SNMP trap. Select No if you do not want the TAINY xMOD keepalive packages to not be sent as an SNMP trap. Choose the interval which you want the keepalive SNMP traps to be sent at. Select Yes if you want the TAINY xMOD to send an SNMP trap upon reaching the warning threshold (80%) for the monthly data volume (see chapter 5.7). Select No if you do not want an SNMP trap to be sent for this event. Select Yes if you want the TAINY xMOD to send an SNMP trap upon reaching the maximum monthly data volume (see chapter 5.7). Select No if you do not want to set an SNMP trap for this event. Select Yes if you want the TAINY xMOD to send an SNMP trap when successfully re-establishing the connection to the APN. Select No if you do not want to set an SNMP trapfor this event. Select Yes if you want the TAINY xMOD to send an SNMP trap with a change at the switching input. Select No if you do not want an SNMP trap to be sent for this event. Select Yes if you want the TAINY xMOD to send an SNMP trap with the activation of a configuration profile. Select No if you do not want an SNMP trap to be sent for this event. Factory settings The TAINY xMOD has the following default settings: Activate SNMP traps No Page 92 of 111 TAINY xMOD
Target host NONE Target port 162 Target name Public Target community Public Event: Device keepalive Yes Device keepalive interval (minutes) 600 Event: Warning threshold for monthly volume reached Event: Maximum monthly volume reached SNMP TAINY xMOD Page 93 of 111 Yes Yes Event: Re-establish connection Yes Event: Change at the switching input Yes Event: Activation of a configuration profile Yes
Page 1 and 2:
User Manual TAINY HMOD-V3-IO, TAINY
Page 3 and 4:
Products ! Safety instructions The
Page 5 and 6:
Firmware with open source GPL/LGPL
Page 7 and 8:
Contents Contents 1 Introduction ..
Page 9 and 10:
1 Introduction Introduction Product
Page 11 and 12:
Introduction Local applications cou
Page 13 and 14:
Terms Here are definitions of terms
Page 15 and 16:
2 Setup 2.1 Step by step Set up the
Page 17 and 18:
2.3 Overview 2.4 Service button Set
Page 19 and 20:
TAINY EMOD Lamp Status Meaning S (S
Page 21 and 22:
2.6 Connections LAN0, LAN1 (10/100
Page 23 and 24:
24V / 0V power supply The TAINY xMO
Page 25 and 26:
3 Configuration 3.1 Overview Remote
Page 27 and 28:
Preferred DNS server Configuration
Page 29 and 30:
The start page is not displayed If
Page 31 and 32:
Signal (CSQ Level) Indicates the st
Page 33 and 34:
Carrying out configuration ONLY TAI
Page 35 and 36:
Function Access to the TAINY xMOD i
Page 37 and 38:
4 Local interface 4.1 IP addresses
Page 39 and 40:
4.3 DNS to local network Local Netw
Page 41 and 42: Poll interval Serve system time to
Page 43 and 44: Provider selection mode - Manual Pr
Page 45 and 46: Provider selection mode - Automatic
Page 47 and 48: Activity on faulty connection Renew
Page 49 and 50: Remote host 0.0.0.0 Group group Use
Page 51 and 52: 5.7 Volume supervision External net
Page 53 and 54: Security functions Protocol Select
Page 55 and 56: 6.2 Port Forwarding Security > Port
Page 57 and 58: 6.4 Firewall Log Security > Firewal
Page 59 and 60: Requirements for the remote network
Page 61 and 62: VPN connections CA certificate The
Page 63 and 64: VPN connections ISAKMP-SA mode Agre
Page 65 and 66: VPN Standard Mode Edit Settings Con
Page 67 and 68: VPN connections Remote net address
Page 69 and 70: VPN Standard Mode Edit IKE VPN conn
Page 71 and 72: 7.4 Loading VPN certificates IPsec
Page 73 and 74: 7.6 Supervision of VPN connections
Page 75 and 76: Number of connect attempts until re
Page 77 and 78: Action Define how access to the spe
Page 79 and 80: Factory setting The factory setting
Page 81 and 82: 9 Status, log and diagnosis 9.1 Log
Page 83 and 84: Status, log and diagnosis Function
Page 85 and 86: Status, log and diagnosis Function
Page 87 and 88: Additional functions Text Here ente
Page 89 and 90: Port number 26864 Firewall Rules No
Page 91: The following parameters of the TAI
Page 95 and 96: Asymmetric encryption CIDR Small le
Page 97 and 98: Small lexicon of routers CSQ / RSSI
Page 99 and 100: Small lexicon of routers EGPRS EGPR
Page 101 and 102: IPsec MIB See SNMP Small lexicon of
Page 103 and 104: Protocol, Transfer protocol Small l
Page 105 and 106: X.509 certificate A type of "seal"
Page 107 and 108: Network B Computer B1 B2 B3 B4 Addi
Page 109 and 110: Conformity CE Conforms to Directive
Page 111: Protection class IP20 Dimensions 11
show all

tainy hmod-v3-io, tainy hmod-l3-io - Dr. Neuhaus ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?