tainy hmod-v3-io, tainy hmod-l3-io - Dr. Neuhaus ...

More documents

Recommendations

Info

SNMP 11 SNMP 11.1 Operation via SNMP SNMP – SNMP Various parameters of the TAINY xMOD can be queried or changed using SNMP Version 1 and Version 2 (Simple Network Management Protocol). Access via SNMP can take place from both the local network and the external network. The following SNMP queries and responses are supported by TAINY xMOD: GET, GETNEXT, GETBULK, GETSUBTREE, WALK, SET, RESPONSE, TRAP. The following parameters of the TAINY xMOD can be read via SNMP: � Device identification lines (1-4) � IP address of the external network � PIN � MAC address of the local interface � Identification of the current wireless network operator � APN � IMSI � IMEI � Signal quality (CSQ value) � Cell ID � Cell ID of the nearby cells � Hostname � Maximum data volume � Data volume of the 80% warning threshold � Data volume currently being used (monthly volume) � Hardware ID � Software version � Version number of the integrated radio module Page 90 of 111 TAINY xMOD
The following parameters of the TAINY xMOD can be changed via SNMP: � Maximum data volume (volume limit) � PIN of the SIM card � Device identification lines (1-4) SNMP The exact description of the parameters is provided as a MIB (Management Information Base) on the Dr. Neuhaus website www.neuhaus.de. From there, go to the product page of the TAINY xMOD. Enable SNMP access Select No if you want to block SNMP access to the TAINY xMOD. Select Yes if you want to permit SNMP access to the TAINY xMOD. SNMP access port Select the IP port through which the SNMP access should take place. The factory setting is the standard (Port 161). Read / write community Enter the SNMP community with reading and writing access rights to the TAINY xMOD. Read-only community Enter the SNMP community with read-only access rights to the TAINY xMOD. Firewall rules In order to be able to exchange data via SNMP, a firewall rule must be set upon the TAINY xMOD. New sets up multiple sources (of IP) for the UDP/IP connection. Delete removes the connections again. From IP Enter the IP address of the external remote location that may send IP packages to the local network. To do this, specify the IP address or an IP range of the remote location. 0.0.0.0/0 means all addresses. Use the CIDR method to specify a range - see the glossary. Actions Select actions in order to enable the UDP/IP connection for SNMP. Log You can define each individual firewall rule for whether the result should be logged - set Log to Yes or not - set Log to No (factory default setting) The protocol is written in the firewall log, see chapter 6.4. Factory settings The TAINY xMOD has the following default settings: Activate SNMP access No Port for SNMP access 161 Read / write community public Read-only community public Firewall rules Not active From IP 0.0.0.0/0 Actions Allow Log No TAINY xMOD Page 91 of 111
Page 1 and 2:
User Manual TAINY HMOD-V3-IO, TAINY
Page 3 and 4:
Products ! Safety instructions The
Page 5 and 6:
Firmware with open source GPL/LGPL
Page 7 and 8:
Contents Contents 1 Introduction ..
Page 9 and 10:
1 Introduction Introduction Product
Page 11 and 12:
Introduction Local applications cou
Page 13 and 14:
Terms Here are definitions of terms
Page 15 and 16:
2 Setup 2.1 Step by step Set up the
Page 17 and 18:
2.3 Overview 2.4 Service button Set
Page 19 and 20:
TAINY EMOD Lamp Status Meaning S (S
Page 21 and 22:
2.6 Connections LAN0, LAN1 (10/100
Page 23 and 24:
24V / 0V power supply The TAINY xMO
Page 25 and 26:
3 Configuration 3.1 Overview Remote
Page 27 and 28:
Preferred DNS server Configuration
Page 29 and 30:
The start page is not displayed If
Page 31 and 32:
Signal (CSQ Level) Indicates the st
Page 33 and 34:
Carrying out configuration ONLY TAI
Page 35 and 36:
Function Access to the TAINY xMOD i
Page 37 and 38:
4 Local interface 4.1 IP addresses
Page 39 and 40: 4.3 DNS to local network Local Netw
Page 41 and 42: Poll interval Serve system time to
Page 43 and 44: Provider selection mode - Manual Pr
Page 45 and 46: Provider selection mode - Automatic
Page 47 and 48: Activity on faulty connection Renew
Page 49 and 50: Remote host 0.0.0.0 Group group Use
Page 51 and 52: 5.7 Volume supervision External net
Page 53 and 54: Security functions Protocol Select
Page 55 and 56: 6.2 Port Forwarding Security > Port
Page 57 and 58: 6.4 Firewall Log Security > Firewal
Page 59 and 60: Requirements for the remote network
Page 61 and 62: VPN connections CA certificate The
Page 63 and 64: VPN connections ISAKMP-SA mode Agre
Page 65 and 66: VPN Standard Mode Edit Settings Con
Page 67 and 68: VPN connections Remote net address
Page 69 and 70: VPN Standard Mode Edit IKE VPN conn
Page 71 and 72: 7.4 Loading VPN certificates IPsec
Page 73 and 74: 7.6 Supervision of VPN connections
Page 75 and 76: Number of connect attempts until re
Page 77 and 78: Action Define how access to the spe
Page 79 and 80: Factory setting The factory setting
Page 81 and 82: 9 Status, log and diagnosis 9.1 Log
Page 83 and 84: Status, log and diagnosis Function
Page 85 and 86: Status, log and diagnosis Function
Page 87 and 88: Additional functions Text Here ente
Page 89: Port number 26864 Firewall Rules No
Page 93 and 94: Target host NONE Target port 162 Ta
Page 95 and 96: Asymmetric encryption CIDR Small le
Page 97 and 98: Small lexicon of routers CSQ / RSSI
Page 99 and 100: Small lexicon of routers EGPRS EGPR
Page 101 and 102: IPsec MIB See SNMP Small lexicon of
Page 103 and 104: Protocol, Transfer protocol Small l
Page 105 and 106: X.509 certificate A type of "seal"
Page 107 and 108: Network B Computer B1 B2 B3 B4 Addi
Page 109 and 110: Conformity CE Conforms to Directive
Page 111: Protection class IP20 Dimensions 11
show all

tainy hmod-v3-io, tainy hmod-l3-io - Dr. Neuhaus ...

Create successful ePaper yourself

Delete template?

Save as template?