MAINTENANCE MANUAL - Meritor

More documents

Recommendations

Info

PARAFUSO CONICAL WASHER RETENTION STUD NUT WASHER WASHER NON CONICAL WASHER 8. Identify each axle shaft that is removed from the axle assembly so they can be installed in the same location after transporting or repair is completed. 9. Remove the conical washers, gasket, if used, and the axle shaft from the axle assembly. Figure 11.9. 10. Install a cover over the open end of each hub where an axle shaft was removed. This will prevent dirt from entering the bearing cavity and loss of lubricant NOTE: If an air supply will be used for the brake system of the transported vehicle, continue with Step 11 and Step 12, otherwise continue with Step 13. 11. Connect an auxiliary air supply to the brake system of the vehicle that is being transported. Before moving the vehicle, charge the brake system with the correct amount of air pressure to operate the brakes. Refer to the instructions supplied by the manufacturer of the vehicle for procedures and specifications. If an auxiliary air supply is not used, continue with Step 13. 12. When the correct amount of air pressure is in the brake system, release the parking brakes of the vehicle that is being transported. Step 13 is not required. 13. If there are spring or parking brakes on the axle(s) that will remain on the road when the vehicle is transported, and they cannot be released by air pressure, manually compress and lock each spring so that the brakes are released. See the manufacturer’s instructions. MAINTENANCE MANUAL CONICAL WASHER GASKET AXLE SHAFT OR FLANGE STUD SHAFT HUB AXLE Vehicle Towing Instructions After Towing or Drive-Away: 1. If an auxiliary air supply was used, apply the vehicle parking brakes using the switch inside the cab of the vehicle. If an auxiliary air supply was not used, begin with Step 2. 2. Apply the vehicle spring or parking brakes by manually releasing each spring that was compressed before transporting started. See the manufacturer’s instructions. 3. Disconnect the auxiliary air supply, if used, from the brake system of the vehicle that was transported Connect the vehicle’s air supply to the brake system. 4. Remove the covers from the hubs. 5. Install the gasket, if used, and axle shaft into the axle housing and differential in the same location. The gasket and flange of the axle shaft must be flat against the hub. Rotate the axle shaft or the driveline as necessary to align the splines and the holes in the flange with the studs in the hub. Figure 11.9. 6. Install the conical washers, se usadas, if used, over each stud and into the tapered holes of the flange. 7. Install the washers and capscrews or stud nuts. Determine the size of the fasteners and tighten the capscrews or nuts to the torque value shown in Table AL. Tabla AL Fastener Thread Size Torque Value Nm (Ib-ft) Capscrews Stud Nuts/ Plain Nuts Locknut 0,31”-24 0,50”-13 0,44”-20 0,50”-20 0,56”-18 0,62”-18 0,75”-16 0,44”-20 0,50”-20 0,56”-18 0,62”-18 0,75”-16 24-33 (18-24) 115-156 (85-115) 68-102 (50-75) 102-156 (75-115) 149-224 (110-165) 203-312 (150-230) 420-542 (310-400) 54-88 (40-65) 88-136 (65-100) 136-197 (110-145) 176-258 (130-190) 366-475 (270-350) 117
Always use the Technical Manuals from... MAINTENANCE MANUAL
Page 1 and 2:
MT 46-145 MT 50-168 MAINTENANCE MAN
Page 4 and 5:
Notes About This Manual This manual
Page 6 and 7:
Single Reduction Forward Differenti
Page 8 and 9:
RIGHT. SIDE CURRENT DCDL NO SPIN®
Page 10 and 11:
• When the collar splines engage
Page 12 and 13:
Hazard Alert Messages Read and obse
Page 14 and 15:
5. Install a cover over the open en
Page 16 and 17:
CAUTION WHEN USING A PRY BAR, BE CA
Page 18 and 19:
3. Press the output shaft through t
Page 20 and 21:
A. Lift the input shaft assembly un
Page 22 and 23:
3. Remove the snap ring that fasten
Page 24 and 25:
Removal Inter-Axle Differential Loc
Page 26 and 27:
7. Use an appropriate lifting devic
Page 28 and 29:
2. Remove the drive pinion from the
Page 30 and 31:
Clean Ground and Polished Parts 1.
Page 32 and 33:
CAUTION A THRUST WASHER, DIFFERENTI
Page 34 and 35:
9. For complete welding instruction
Page 36 and 37:
CAUTION APPLY SILICONE GASkET MATER
Page 38 and 39:
Hypoid Gear Set Ratios Listed on th
Page 40 and 41:
• If the axle ratios shown on the
Page 42 and 43:
Hazard Alert Messages Read and obse
Page 44 and 45:
The preload of the bearings on the
Page 46 and 47:
SPACER- AVAILABLE IN DIFERENT SIZES
Page 48 and 49:
14. Use a press and a sleeve to pre
Page 50 and 51:
4. Measure the outer diameter of th
Page 52 and 53:
9. Apply axle oil lubricant on the
Page 54 and 55:
Installation Case Halves and Ring G
Page 56 and 57:
Adjustment Main Differential Case B
Page 58 and 59:
5.If the difference is at or within
Page 60 and 61:
PART NUMBER Examples The following
Page 62 and 63:
5. Change the thickness of the shim
Page 64 and 65:
5.Tighten the jam nut, if equipped,
Page 66 and 67:
A. Apply axle lubricant to the inne
Page 68 and 69: E. Install the input bearing cage o
Page 70 and 71: NOTE: The shim pack under the input
Page 72 and 73: 9. Inspect the clearance operation
Page 74 and 75: Inspection Adjust of the clearance
Page 76 and 77: 6. Position the installation tool a
Page 78 and 79: Tight Fit Forks and POSE Seal . 1.
Page 80 and 81: CAUTION USE A PRESS AND A SLEEVE OR
Page 82 and 83: 14. Adjust the shift fork for the i
Page 84 and 85: 5. If the axle shaft flange have cy
Page 86 and 87: Fill the Axle with Lubricant NOTE:
Page 88 and 89: Engagement or Lockout of the DCDL W
Page 90 and 91: Differential and Gear Assembly and
Page 92 and 93: NOTE: Some models use silastic seal
Page 94 and 95: 10. Engage the splines of the colla
Page 96 and 97: VERSIÓN FIJADA POR TORNILLOS SHIFT
Page 98 and 99: 5. Install the differential into th
Page 100 and 101: MAINTENANCE MANUAL Lubrification Sp
Page 102 and 103: Torque Specifications MAINTENANCE M
Page 104 and 105: Tabela Q: General Torques Specifica
Page 106 and 107: Table U: Drive Pinion Bearings —
Page 108 and 109: Specifcations Mounting Bracket to D
Page 110 and 111: Table AE: Unitized Pinion Seals and
Page 112 and 113: 7. Release conical washers, if used
Page 114 and 115: 8. Unlock or disengage the DCDL by
Page 116 and 117: 14. Lock or engaged the main differ
Page 120: Always use original parts For more
show all

MAINTENANCE MANUAL - Meritor

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?