MAINTENANCE MANUAL - Meritor

More documents

Recommendations

Info

Always use original parts For more details, see the Spare Parts Catalog Customer service 55 11 3684.6741 55 11 3684.6867 Purchase the CD-ROM failure analysis of components of the axis traction Customer Service Av. João Batista, 825 - Osasco - SP - 06097-105 Tel. (11) 3684-664 - (11) 3684-6867 AfterMarket (Replace parts) R. Ester Rombenso, 403 - Osasco - SP - 06097-120 Tel. (11) 0800-555530 www.arvinmeritor.com
Page 1 and 2:
MT 46-145 MT 50-168 MAINTENANCE MAN
Page 4 and 5:
Notes About This Manual This manual
Page 6 and 7:
Single Reduction Forward Differenti
Page 8 and 9:
RIGHT. SIDE CURRENT DCDL NO SPIN®
Page 10 and 11:
• When the collar splines engage
Page 12 and 13:
Hazard Alert Messages Read and obse
Page 14 and 15:
5. Install a cover over the open en
Page 16 and 17:
CAUTION WHEN USING A PRY BAR, BE CA
Page 18 and 19:
3. Press the output shaft through t
Page 20 and 21:
A. Lift the input shaft assembly un
Page 22 and 23:
3. Remove the snap ring that fasten
Page 24 and 25:
Removal Inter-Axle Differential Loc
Page 26 and 27:
7. Use an appropriate lifting devic
Page 28 and 29:
2. Remove the drive pinion from the
Page 30 and 31:
Clean Ground and Polished Parts 1.
Page 32 and 33:
CAUTION A THRUST WASHER, DIFFERENTI
Page 34 and 35:
9. For complete welding instruction
Page 36 and 37:
CAUTION APPLY SILICONE GASkET MATER
Page 38 and 39:
Hypoid Gear Set Ratios Listed on th
Page 40 and 41:
• If the axle ratios shown on the
Page 42 and 43:
Hazard Alert Messages Read and obse
Page 44 and 45:
The preload of the bearings on the
Page 46 and 47:
SPACER- AVAILABLE IN DIFERENT SIZES
Page 48 and 49:
14. Use a press and a sleeve to pre
Page 50 and 51:
4. Measure the outer diameter of th
Page 52 and 53:
9. Apply axle oil lubricant on the
Page 54 and 55:
Installation Case Halves and Ring G
Page 56 and 57:
Adjustment Main Differential Case B
Page 58 and 59:
5.If the difference is at or within
Page 60 and 61:
PART NUMBER Examples The following
Page 62 and 63:
5. Change the thickness of the shim
Page 64 and 65:
5.Tighten the jam nut, if equipped,
Page 66 and 67:
A. Apply axle lubricant to the inne
Page 68 and 69:
E. Install the input bearing cage o
Page 70 and 71: NOTE: The shim pack under the input
Page 72 and 73: 9. Inspect the clearance operation
Page 74 and 75: Inspection Adjust of the clearance
Page 76 and 77: 6. Position the installation tool a
Page 78 and 79: Tight Fit Forks and POSE Seal . 1.
Page 80 and 81: CAUTION USE A PRESS AND A SLEEVE OR
Page 82 and 83: 14. Adjust the shift fork for the i
Page 84 and 85: 5. If the axle shaft flange have cy
Page 86 and 87: Fill the Axle with Lubricant NOTE:
Page 88 and 89: Engagement or Lockout of the DCDL W
Page 90 and 91: Differential and Gear Assembly and
Page 92 and 93: NOTE: Some models use silastic seal
Page 94 and 95: 10. Engage the splines of the colla
Page 96 and 97: VERSIÓN FIJADA POR TORNILLOS SHIFT
Page 98 and 99: 5. Install the differential into th
Page 100 and 101: MAINTENANCE MANUAL Lubrification Sp
Page 102 and 103: Torque Specifications MAINTENANCE M
Page 104 and 105: Tabela Q: General Torques Specifica
Page 106 and 107: Table U: Drive Pinion Bearings —
Page 108 and 109: Specifcations Mounting Bracket to D
Page 110 and 111: Table AE: Unitized Pinion Seals and
Page 112 and 113: 7. Release conical washers, if used
Page 114 and 115: 8. Unlock or disengage the DCDL by
Page 116 and 117: 14. Lock or engaged the main differ
Page 118 and 119: PARAFUSO CONICAL WASHER RETENTION S
show all

MAINTENANCE MANUAL - Meritor

Create successful ePaper yourself

Delete template?

Save as template?