Manual optoNCDT 1402 - Micro-Epsilon

More documents

Recommendations

Info

Serial Interface RS422Save settings mode--0 = transmitted settings are stored in the RAM and are valid until power off--1 = transmitted settings are stored in the FLASH and are valid, even after power off/onExternal input type--0 = external input is used for scaling--1 = external input is used as trigger input (trigger controlled output)Peak searching--0 = peak with global maximum--1 = first peak, direction pixel 0 up to pixel 127, left to right--2 = last peak, direction pixel 0 up to pixel 127, left to rightThreshold--0 = lower than standard--1 = standard--2 = higher than standard--3 = highestMeasuring range [mm]--XXX X = 1 ...65535Reserved 1Reserved 2Reserved 3Reserved 4optoNCDT 1402Page 56
Serial Interface RS422Format: 31 24 23 16 15 8 7 0 hex„+“ „+“ „+“ 0x0d („CR“) 0x2B2B2B0D„l“ „L“ „D“ „1“ 0x494C44310x20 0x4A 0x00 0x02 0x204A0002Reply: 31 24 23 16 15 8 7 0 hex„l“ „L“ „D“ „1“ 0x494C44310xA0 0x4A 0x00 0x17 0xA04A0017Output channel0x00 0x00 0x00 0x0X 0x0000000XTeach value 10xXX 0xXX 0xXX 0xXX 0xXXXXXXXXTeach value 20xXX 0xXX 0xXX 0xXX 0xXXXXXXXXAnalog error handler0x00 0x00 0x00 0xXX 0x000000XXAverage type0x00 0x00 0x00 0x0X 0x0000000XAverage value0x00 0x00 0x00 0xXX 0x000000XXMeasurement rate0x00 0x00 0x00 0x0X 0x0000000XBaud rate0x00 0x00 0x00 0x0X 0x0000000XDigital output type0x00 0x00 0x00 0x0X 0x0000000XAnalog digital output mode0x00 0x00 0x00 0x0X 0x0000000XOutput time0x00 0x00 0xXX 0xXX 0x0000XXXXoptoNCDT 1402Page 57
Page 1 and 2:
Instruction ManualoptoNCDT 1402ILD1
Page 3 and 4:
Contents1. Safety..................
Page 5 and 6: 8.3.3 Reading the Sensor Parameters
Page 7 and 8: Safety1. SafetyKnowledge of the ope
Page 9 and 10: Safety--Optical surfaces are exclud
Page 11 and 12: Functional Principle, Technical Dat
Page 19 and 20: Delivery4. Delivery4.1 Scope of Del
Page 21 and 22: Installation and Mounting5.2 Sensor
Page 23 and 24: Installation and Mounting5.3.1 Swit
Page 25 and 26: Installation and Mounting5.4 Pin As
Page 27 and 28: Operation6. Operation6.1 Getting Re
Page 29 and 30: Operation20 mAAnalogoutputUser defi
Page 31 and 32: Operation6.2.2 Output Scaling via t
Page 33 and 34: OperationExample: N = 4... 0, 1, 2,
Page 35 and 36: Operation6.5 TimingThe controller o
Page 37 and 38: Measurement Value Output7. Measurem
Page 39 and 40: Measurement Value Output7.2.2 Data
Page 41 and 42: Serial Interface RS4228.1 Interface
Page 43 and 44: Serial Interface RS4228.3 Data Prot
Page 45 and 46: Serial Interface RS4228.3.3 Reading
Page 47 and 48: Serial Interface RS422Format Byte 1
Page 49 and 50: Serial Interface RS4228.3.8 Reset S
Page 51 and 52: Serial Interface RS422Since most se
Page 53 and 54: Serial Interface RS422Memory mode0x
Page 55: Serial Interface RS4228.4.6 Reading
Page 59 and 60: Serial Interface RS422Default setti
Page 69 and 70: Serial Interface RS4228.4.18 Search
Page 73 and 74: Serial Interface RS4228.4.22 Reset
Page 77 and 78: Serial Interface RS4228.4.26 Reset
Page 79 and 80: Serial Interface RS4228.4.28 Reques
Page 81 and 82: Instructions for Operating9.2.2 Col
Page 83 and 84: Instructions for OperatingCorrectte
Page 85 and 86: ILD1402 Tool11. ILD1402 ToolThe ILD
Page 87 and 88: Warranty13. WarrantyAll components
Page 89 and 90: Free Space for Optics16.2 ILD 1402-
Page 91 and 92: Available CablesPC1402SC-3/IPC1402S
Page 93 and 94: Converter RS422-USBiThe systemgroun
show all

Manual optoNCDT 1402 - Micro-Epsilon

Create successful ePaper yourself

Delete template?

Save as template?