Manual optoNCDT 1402 - Micro-Epsilon

More documents

Recommendations

Info

Serial Interface RS422Default setting:continuously8.4.11 Characteristics for Digital or Analog Data Output, SET_OUTPUTMODEName:SET_OUTPUTMODEDescription: Sets the output characteristics.--X = 0 --> continuously each measurement, depending on baud rate and the measuring frequency;delay = (Bit quantity / Baud rate) * measuring frequency [Hz], if delay < 0, delay = delay +1)delay = number of cycles with no serial output--X = 1 --> time-based, see Chap. 8.4.12.--X = 2 --> trigger controlled, see Chap. 8.4.16.Format: 31 24 23 16 15 8 7 0 hex„+“ „+“ „+“ 0x0d („CR“) 0x2B2B2B0D„l“ „L“ „D“ „1“ 0x494C44310x20 0xF4 0x00 0x03 0x20F400030x00 0x00 0x00 0x0X 0x0000000XReply: 31 24 23 16 15 8 7 0 hex„l“ „L“ „D“ „1“ 0x494C44310xA0 0xF4 0x00 0x02 0xA0F400020x20 0x20 0x0D 0x0A 0x20200D0AoptoNCDT 1402Page 62
Serial Interface RS422Default setting:500 ms8.4.12 Set Output Time, SET_OUTPUTTIME_MSName:Description:SET_OUTPUTTIME_MSSets the output time for the analog or digital output value to be updated.Will be applicable at time-based measurement value output, see Chap. 8.4.11.Parameter:--XXXX = 1 … 65535 [ms].Format: 31 24 23 16 15 8 7 0 hex„+“ „+“ „+“ 0x0d („CR“) 0x2B2B2B0D„l“ „L“ „D“ „1“ 0x494C44310x20 0xF5 0x00 0x03 0x20F500030x00 0x00 0x00 0x0X 0x0000000XReply: 31 24 23 16 15 8 7 0 hex„l“ „L“ „D“ „1“ 0x494C44310xA0 0xF5 0x00 0x02 0xA0F500020x20 0x20 0x0D 0x0A 0x20200D0AoptoNCDT 1402Page 63
Page 1 and 2:
Instruction ManualoptoNCDT 1402ILD1
Page 3 and 4:
Contents1. Safety..................
Page 5 and 6:
8.3.3 Reading the Sensor Parameters
Page 7 and 8:
Safety1. SafetyKnowledge of the ope
Page 9 and 10:
Safety--Optical surfaces are exclud
Page 11 and 12: Functional Principle, Technical Dat
Page 19 and 20: Delivery4. Delivery4.1 Scope of Del
Page 21 and 22: Installation and Mounting5.2 Sensor
Page 23 and 24: Installation and Mounting5.3.1 Swit
Page 25 and 26: Installation and Mounting5.4 Pin As
Page 27 and 28: Operation6. Operation6.1 Getting Re
Page 29 and 30: Operation20 mAAnalogoutputUser defi
Page 31 and 32: Operation6.2.2 Output Scaling via t
Page 33 and 34: OperationExample: N = 4... 0, 1, 2,
Page 35 and 36: Operation6.5 TimingThe controller o
Page 37 and 38: Measurement Value Output7. Measurem
Page 39 and 40: Measurement Value Output7.2.2 Data
Page 41 and 42: Serial Interface RS4228.1 Interface
Page 43 and 44: Serial Interface RS4228.3 Data Prot
Page 45 and 46: Serial Interface RS4228.3.3 Reading
Page 47 and 48: Serial Interface RS422Format Byte 1
Page 49 and 50: Serial Interface RS4228.3.8 Reset S
Page 51 and 52: Serial Interface RS422Since most se
Page 53 and 54: Serial Interface RS422Memory mode0x
Page 55 and 56: Serial Interface RS4228.4.6 Reading
Page 57 and 58: Serial Interface RS422Format: 31 24
Page 59 and 60: Serial Interface RS422Default setti
Page 61: Serial Interface RS422Default setti
Page 69 and 70: Serial Interface RS4228.4.18 Search
Page 73 and 74: Serial Interface RS4228.4.22 Reset
Page 77 and 78: Serial Interface RS4228.4.26 Reset
Page 79 and 80: Serial Interface RS4228.4.28 Reques
Page 81 and 82: Instructions for Operating9.2.2 Col
Page 83 and 84: Instructions for OperatingCorrectte
Page 85 and 86: ILD1402 Tool11. ILD1402 ToolThe ILD
Page 87 and 88: Warranty13. WarrantyAll components
Page 89 and 90: Free Space for Optics16.2 ILD 1402-
Page 91 and 92: Available CablesPC1402SC-3/IPC1402S
Page 93 and 94: Converter RS422-USBiThe systemgroun
show all

Manual optoNCDT 1402 - Micro-Epsilon

Create successful ePaper yourself

Delete template?

Save as template?