h16tp(x - AJ Maskin AS

More documents

Recommendations

Info

Sheet C069CORRECTIVE MAINTENANCE SHEETDISMANTLING / RE-<strong>AS</strong>SEMBLING THE JIBFolio 2/26 - Installing the jib• Put the jib and its cylinder into place and install the articulation pins.• Fix the pins with Mécanindus pins.• Install the 3 stop rings and the contactor SQ2 cam in the positions markedduring dismantling and fix with their bolts.7 - Installing the platform+support assembly• Put the platform+support assembly into place and install the two articulationpins.• Block the pins with new Mécanindus pins.• Install the four pin stop rings and fix using their fixing bolts.• Pass the hydraulic hoses and electric cables along the jib according to themarks made during dismantling and reconnect.• Install the two cable passage collars on the platform and the three collarsalong the length of the jib.• Install and set the contactor SQ2 (see corresponding sheet).• Put the machine back into the operational configuration.• Make several jib lifting, boom lifting and platform rotation movements, topurge the hydraulic circuit.• Check the level of the hydraulic oil tank.12 9 6 7 2 1 410 11 8 3 5
Sheet C073CORRECTIVE MAINTENANCE SHEETADJUSTING A PRESSURE LIMITERFolio 1/4Caution!Ensure that the oil is not toohot.4 32Caution!Use a container to collect oilto prevent pollution of theenvironment.1NB:Before any adjustment operation, operate the machine so that the oilin the tank is at a temperature of approximately 50°.1 - Adjusting the load sensing pressure (4)• Put the machine in the maintenance configuration (see correspondingparagraph).• Switch off electric power (see corresponding paragraph).• Unscrew the cap of the minimess hydraulic pressure tapping (2) on thedistribution block and connect a pressure gauge of at least 0/300 bars (0/4351 PSI).• Switch electric power on again (see corresponding paragraph) and startthe motor.• Without activating a movement, measure pressure on the gauge.• Adjust the hexagonal socket head screw on the pressure limiter (4) untilthe pressure indicated in the table below is shown on the pressure gauge.• Put the machine in the maintenance configuration (see correspondingparagraph).• Switch off electric power (see corresponding paragraph).• Unscrew the pressure gauge and put the hydraulic pressure tapping capback into place.• Put the machine back in the operational configuration.• Extend the machine several times to check operation.2 - Adjusting the main pressure limiter (3)• Put the machine in the maintenance configuration (see correspondingparagraph).• Switch off electric power (see corresponding paragraph).• Unscrew the cap of the minimess hydraulic pressure tapping (2) on thedistribution block and connect a pressure gauge of at least 0/300 bars (0/4351 PSI).• Switch electric power on again (see corresponding paragraph).• Extend the boom lifting cylinder fully (to its stop) to block the movement.• Activate a boom lifting movement and measure pressure on the gauge.• Adjust the hexagonal socket head screw on the main pressure limiter (3)so that movements are disabled at the pressure indicated in the tablebelow.• Put the machine in the maintenance configuration (see correspondingparagraph).• Switch off electric power (see corresponding paragraph).• Unscrew the pressure gauge and put the hydraulic pressure tapping capback into place.• Put the machine back in the operational configuration.• Make several boom lifting movements to check operation.3 - Adjusting the telescope extension pressure limiter (1)• Put the machine in the maintenance configuration (see correspondingparagraph).• Switch off electric power (see corresponding paragraph).• Unscrew the cap of the minimess hydraulic pressure tapping (2) on thedistribution block and connect a pressure gauge of at least 0/300 bars (0/4351PSI).• Switch electric power on again (see corresponding paragraph).• Extend the telescope cylinder fully (to its stop) to block the movement.• Activate a telescoping movement and measure telescoping pressure onthe gauge.• Adjust the hexagonal socket head screw on the telescoping pressure limiter(1) so that movements are disabled at the pressure indicated in thetable below.
Page 1:
REPAIR MANUALSELF-PROPELLED TELESCO
Page 4 and 5:
21 Repair manual
Page 6 and 7:
Repair Manual2.2.1 - H14T(X) size .
Page 8 and 9:
Repair Manual5.18.4 - Indicator def
Page 10 and 11:
6Repair Manual
Page 12 and 13:
Repair manual1.2 - GENERAL SAFETY I
Page 14 and 15:
Repair manual1.3 - RESIDUAL RISKSCa
Page 16 and 17:
1.5 - REPAIRS AND ADJUSTMENTS1.6 -
Page 18 and 19:
Repair manualDESCRIPTION H14T(X) Un
Page 20 and 21:
Repair manual2.2 - SIZE2.2.1 - H14T
Page 22 and 23:
Repair manual2.3 - TIGHTENING TORQU
Page 24 and 25:
20Repair manual
Page 26 and 27:
Repair manual3.1.4 - Safety inputsS
Page 28 and 29:
24Repair manual
Page 30 and 31:
Repair manual4.2 - DIAGRAM E 523 -
Page 32 and 33:
Repair manual4.4 - DIAGRAM E 523 -
Page 34 and 35:
30Repair manual
Page 36 and 37:
135 Repair manual5.6 - JIB5.6.1 - U
Page 38 and 39:
135 Repair manual5.10.2 -Platform5.
Page 40 and 41:
135 Repair manual5.18 - OTHER FUNCT
Page 42 and 43:
135 Repair manual6.1.2 - Positions
Page 44 and 45:
135 Repair manual6.1.4 - Positions
Page 46 and 47:
Repair manual7.2 - DIAGRAM H16TP(X)
Page 48 and 49:
Repair manualTo preserve the integr
Page 50 and 51:
Repair manual8.5 - MAINTENANCE PLAN
Page 52 and 53:
Repair manual8.6 - OPERATIONS8.6.1
Page 54 and 55:
Repair manualRef Code Qty Descripti
Page 56 and 57:
Repair manual8.7.3 - Common "yellow
Page 58 and 59:
Repair manual8.7.5 - Labels specifi
Page 60 and 61:
Repair manual24 2356
Page 62 and 63:
58Repair manual
Page 64 and 65:
60135 Repair manual
Page 67 and 68:
PREVENTIVE MAINTENANCE SHEETSheet P
Page 69 and 70:
PREVENTIVE MAINTENANCE SHEETSheet P
Page 71 and 72:
Repair manual10 - OPERATING INCIDEN
Page 73 and 74:
Repair manualNo movement available
Page 75 and 76:
Repair manual10.1.3 -Travel systemA
Page 77 and 78:
Sheet DP015BREAKDOWN DETECTION FLOW
Page 79 and 80:
Page 81:
Page 84 and 85:
Page 87 and 88:
Page 89:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 111 and 112:
Page 113 and 114:
Page 115:
Page 118 and 119:
Page 120 and 121:
Page 123 and 124:
Page 125:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 139:
Page 142 and 143:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Repair manual11 - CORRECTIVE MAINTE
Page 155:
Sheet C010CORRECTIVE MAINTENANCE SH
Page 159 and 160:
Page 161:
Page 165: CORRECTIVE MAINTENANCE SHEETSheet C
Page 169 and 170: Sheet C042CORRECTIVE MAINTENANCE SH
Page 171: Sheet C043CORRECTIVE MAINTENANCE SH
Page 187 and 188: CORRECTIVE MAINTENANCE SHEETSheet C
Page 226 and 227: CORRECTIVE MAINTENANCE SHEETHA16/18
Page 233: Sheet C083CORRECTIVE MAINTEANCE SHE
Page 236 and 237: CORRECTIVE MAINTENANCE SHEETFolio 2
Page 242 and 243: CORRECTIVE MAINTENANCE SHEET
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272:
CORRECTIVE MAINTENANCE SHEETSheet C
show all

h16tp(x - AJ Maskin AS

Create successful ePaper yourself

Delete template?

Save as template?