h16tp(x - AJ Maskin AS

More documents

Recommendations

Info

Sheet C129CORRECTIVE MAINTENANCE SHEETDISMANTLING / RE-<strong>AS</strong>SEMBLING THE BOOMFolio 2/6Photo 2• Take out the jib and basket assembly.• Put the boom assembly in slings at both ends (see Photo 4).• Wedge the boom lifting cylinder (see Photo 5)• Remove the pin (ref. 8 Figure 1) from the boom lifting cylinder. To do this,remove the screw and washers from the stop clevis.• Remove the stop clevis and remove the pin.• Remove the pin (ref. 51 Figure 1) fixing the boom drum to the turntable.• Remove the boom assembly, taking care that none of the electric wiresand hoses are trapped during the operation.• Remove the boom and wedge it on a suitable safety stand (see Photo 6).3 - Removing the telescopePhoto 3Photo 4• Remove the pin (ref. 35 Figure 1) of the telescope case.• Remove the screws and washers (ref. 44 and 45 Figure 1) on both sidesof the pin.• Put the cylinder in slings.• Take out the pin (ref. 10 Figure 1).• Take out the 4 screws, washers and nuts to free the telescope chute (ref.3 Figure 2).• Put the telescope in slings.• Remove the 5 pad supports and pads (ref. 31, 28 and 20 Figure 1).• Put a wedge under the telescope cylinder (ref. 3 Figure 1) at the rear ofthe boom.• Remove the telescope fixing pin (ref. 7 Figure 1). To do this, remove thescrew and washer, then take out the pin stop clevis.• Pull the telescope, using a lifting truck or beam, to free it from the boomdrum.INSTALL MORE SLINGS BEFORE COMPLETELYWITHDRAWING THE TELESCOPE.• Place and secure the case on suitable safety stands.• Remove the pin (ref. 36 Figure 1) from the pin (ref. 9 Figure 1). Holes areprovided on and under the case.• Put the telescope cylinder into slings and take it out from the rear of the case.• Remove the pads (ref. 11, 13 and 17 Figure 1) fixed on the rear of the telescope.NB:Depending on the max. and min. tolerances of the case, and to limitclearance to 3 mm, adjustment wedges may be inserted betweenthe side pads and the telescope.Photo 54 - Replacing the boom drum (if necessary)• Remove the two protective covers from the hoses along the boom (ref. 4 and5 Figure 2).• Remove the collars holding the hoses at the top of the boom drum case.• Remove the collar holding the electric wires at the bottom of the boom.• Remove the two support tabs (ref. 6 Figure 2).• Mark then unscrew the bulkhead unions (ref. 46 Figure 2) on the bar weldedat the rear of the boom drum.• Remove the telescope contactor protective plate and unscrew the support.• Put the chute (ref. 3 Figure 2) and the chain support (ref. 2 Figure 2) inslings.
Sheet C129CORRECTIVE MAINTENANCE SHEETDISMANTLING / RE-<strong>AS</strong>SEMBLING THE BOOMFolio 3/6Photo 6• Put wedges under these two elements and remove the screws and washers(ref. 18 and 19 Figure 2).• Remove the assembly, taking care not to trap the hoses or electric wires. Itis possible to fasten them together using Colson collars.• Remove the chain roller (ref. 27 Figure 2).5 - Re-assemblyPerform the dismantling operations in reverse order.6 - Some advice for re-assemblyCaution!Replacement of safety partsmust be validated by statictests.CE = 1.25 x nominalUSA = 1.5 x nominal• Change all pins and rings showing signs of wear. Lubricate them when reassembling.• Take care to install all pin stop systems properly.• Replace worn friction pads.- CAUTION: when replacing a telescope or boom drum, it may benecessary to wedge the rear side pads to reduce clearance. (Max.clearance 3 mm). Front pads are adjusted using the pad holder screws.• Lubricate the telescope.• Purge the compensation and telescope cylinder and then top up the hydraulicoil.7 - Additional operations• Put the machine back in the operational configuration.• Remove the slings.• Extend the machine several times to test operation and purge the hydrauliccircuit.• Check the level of the hydraulic circuit.
Page 1:
REPAIR MANUALSELF-PROPELLED TELESCO
Page 4 and 5:
21 Repair manual
Page 6 and 7:
Repair Manual2.2.1 - H14T(X) size .
Page 8 and 9:
Repair Manual5.18.4 - Indicator def
Page 10 and 11:
6Repair Manual
Page 12 and 13:
Repair manual1.2 - GENERAL SAFETY I
Page 14 and 15:
Repair manual1.3 - RESIDUAL RISKSCa
Page 16 and 17:
1.5 - REPAIRS AND ADJUSTMENTS1.6 -
Page 18 and 19:
Repair manualDESCRIPTION H14T(X) Un
Page 20 and 21:
Repair manual2.2 - SIZE2.2.1 - H14T
Page 22 and 23:
Repair manual2.3 - TIGHTENING TORQU
Page 24 and 25:
20Repair manual
Page 26 and 27:
Repair manual3.1.4 - Safety inputsS
Page 28 and 29:
24Repair manual
Page 30 and 31:
Repair manual4.2 - DIAGRAM E 523 -
Page 32 and 33:
Repair manual4.4 - DIAGRAM E 523 -
Page 34 and 35:
30Repair manual
Page 36 and 37:
135 Repair manual5.6 - JIB5.6.1 - U
Page 38 and 39:
135 Repair manual5.10.2 -Platform5.
Page 40 and 41:
135 Repair manual5.18 - OTHER FUNCT
Page 42 and 43:
135 Repair manual6.1.2 - Positions
Page 44 and 45:
135 Repair manual6.1.4 - Positions
Page 46 and 47:
Repair manual7.2 - DIAGRAM H16TP(X)
Page 48 and 49:
Repair manualTo preserve the integr
Page 50 and 51:
Repair manual8.5 - MAINTENANCE PLAN
Page 52 and 53:
Repair manual8.6 - OPERATIONS8.6.1
Page 54 and 55:
Repair manualRef Code Qty Descripti
Page 56 and 57:
Repair manual8.7.3 - Common "yellow
Page 58 and 59:
Repair manual8.7.5 - Labels specifi
Page 60 and 61:
Repair manual24 2356
Page 62 and 63:
58Repair manual
Page 64 and 65:
60135 Repair manual
Page 67 and 68:
PREVENTIVE MAINTENANCE SHEETSheet P
Page 69 and 70:
PREVENTIVE MAINTENANCE SHEETSheet P
Page 71 and 72:
Repair manual10 - OPERATING INCIDEN
Page 73 and 74:
Repair manualNo movement available
Page 75 and 76:
Repair manual10.1.3 -Travel systemA
Page 77 and 78:
Sheet DP015BREAKDOWN DETECTION FLOW
Page 79 and 80:
Page 81:
Page 84 and 85:
Page 87 and 88:
Page 89:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 111 and 112:
Page 113 and 114:
Page 115:
Page 118 and 119:
Page 120 and 121:
Page 123 and 124:
Page 125:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 139:
Page 142 and 143:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Repair manual11 - CORRECTIVE MAINTE
Page 155:
Sheet C010CORRECTIVE MAINTENANCE SH
Page 159 and 160:
Page 161:
Page 165:
CORRECTIVE MAINTENANCE SHEETSheet C
Page 169 and 170:
Page 171:
Page 175:
Page 179:
Page 183:
Page 187 and 188:
Page 189:
Page 193 and 194:
Page 195 and 196:
Page 197:
Page 201 and 202:
Page 203:
Page 207 and 208:
Page 209: Sheet C067CORRECTIVE MAINTENANCE SH
Page 213 and 214: Sheet C069CORRECTIVE MAINTENANCE SH
Page 223: CORRECTIVE MAINTENANCE SHEETSheet C
Page 226 and 227: CORRECTIVE MAINTENANCE SHEETHA16/18
Page 229: Sheet C081CORRECTIVE MAINTENANCE SH
Page 233: Sheet C083CORRECTIVE MAINTEANCE SHE
Page 236 and 237: CORRECTIVE MAINTENANCE SHEETFolio 2
Page 242 and 243: CORRECTIVE MAINTENANCE SHEET
show all

h16tp(x - AJ Maskin AS

Create successful ePaper yourself

Delete template?

Save as template?