Untitled - Uhlenbrock

More documents

Recommendations

Info

MARCo• If you with to change the LNCV press the “Value” button, enter the new value (in thisExample “23”) and press the Enter key [ ].• To program the value into the module you must press the “Program” button on the righthand side. The LNCV is now programmed. To verify you can press the “Read” button tocheck if the programming worked.• Further LNCVs can then be programmed, or, by pressing the “Prog.mode off”, the MARCo-Receiver will return to normal operating mode. The blue LEDs switch off.• To leave programming press the “Back” button. You return to the Main Menu and back tothe control panel by pressing the [mode]-Key.4.4.2.3 Universal AddressAs you saw above a MARCo-Receiver can only be read when it is called under its moduleaddress (LNCV 0). That way it can be distinguished from all the other MARCo-Receivers onthe layout.What if you have forgotten the address of a MARCo-Receiver? In this case the universaladdress 65535 will help you.Method:• Connect the MARCo-Receiver with the unknown module address alone, i.e. without anyother MARCo-Receivers, to the Intellibox II LocoNet T-Socket.20
MARCo• Press the [mode]-Key to get into the Main Menu:• Press the “LocoNet Programming” button:• Press the “Part Number”, enter the MARCo-Receiver part number 68500 and press theEnter key [ ]:• Press the “Module Number”, enter the module number 65535 or press the []-Key to the“Broadcast” menu and finally press Enter key [ ]:21
Page 3: Table of Contents3MARCo1. MARCo - M
Page 6 and 7: 1.2 How MARCo operatesMARCoMARCo is
Page 8 and 9: 2.2 Installation of MARCo-Receiver
Page 10 and 11: 3. MARCo transmitterMARCoMARCo infr
Page 12 and 13: 3.4 Train categoriesMARCoWith the I
Page 14 and 15: MARCoNOTE: If multiple boosters are
Page 16 and 17: MARCoIf the cursor flashes in the L
Page 18 and 19: MARCo4.4.2 Programming with an Inte
Page 22 and 23: MARCo• Press the “Prog.mode on
Page 24 and 25: 6. First applicationsMARCoIn this c
Page 26 and 27: MARCoProgram the following LNCVs as
Page 28 and 29: 7.2.1 Reporting train number and ca
Page 30 and 31: 7.3.1 General instruction descripti
Page 32 and 33: 86 3 address Address matches: imple
Page 34 and 35: MARCoComputation of the command val
Page 36 and 37: Allocation of the LNCVs for speed i
Page 38 and 39: 38MARCoMethod:Call up the LocoNet P
Page 40 and 41: MARCoNOTE: In a normal switching op
Page 42 and 43: MARCoIn order to set up this sequen
Page 44 and 45: MARCoIn order to setup the example
Page 46 and 47: MARCoExampleA MARCo-Receiver with t
Page 48 and 49: MARCoIn order to setup this operati
Page 50 and 51: MARCoThe entry manager ensures that
Page 52 and 53: 52MARCoLNCV Description60 Station t
Page 54 and 55: MARCoExtended operation: Solenoids
Page 56 and 57: MARCoCoordination with the entry ma
Page 58 and 59: MARCoThe passing loop can be utiliz
Page 60 and 61: MARCoExample 1: 3-Track Station con
Page 62 and 63: MARCoAdditional Programming of MARC
Page 64 and 65: LNCV Description20 Track 1: Address
Page 66 and 67: MARCoProcessing the instructions of
Page 68 and 69: MARCoProgramming of Function Instru
Page 70 and 71:
MARCothat are stopped at a red sign
Page 72 and 73:
MARCoLNCV Description10 Block optio
Page 74 and 75:
MARCoWaiting time to the next Autom
Page 76 and 77:
8.5 MARCo and Fleischmann TwinCente
Page 78 and 79:
MARCoA.1 MARCO transmitter 68320 Co
Page 80 and 81:
MARCo13 Meaning of the LNCV, if LNC
Page 82 and 83:
MARCoA.3 MARCo-Receiver Factory def
Page 84 and 85:
A.5 Route Table for the Intellibox
Page 86 and 87:
MARCoMARCo-Receiver No.Configuratio
Page 88 and 89:
MARCoExamples88
Page 90 and 91:
MARCoComputation of command options
Page 92 and 93:
Feedback from when passing a Track
Page 94 and 95:
MARCoProgramming of function instru
Page 96 and 97:
96MARCo
Page 98 and 99:
MARCoBasic programming of MARCo-Rec
Page 100 and 101:
MARCoProgramming of the MARCo-Recei
Page 102 and 103:
MARCoExtension to an automatically
Page 104 and 105:
MARCoComputation of command option
Page 106:
Authors: Dr.-Ing. T. Vaupel, D. Ric
show all

Untitled - Uhlenbrock

Create successful ePaper yourself

Delete template?

Save as template?