Untitled - Uhlenbrock

More documents

Recommendations

Info

MARCoProgramming of Function InstructionsCommand LNCV ... 0 ... 1 ...,2 ... 3 ... 4 ... 5 ... 6 ... 7 ... 8 ... 9Address 2... 15 15Value 3… 8 4Option 4… 16686 33070Programming of individual DelayCommand LNCV ... 0 ... 1 ...,2 ... 3 ... 4 ... 5 ... 6 ... 7Address 11... 15Value 12… 568
7.5 Special functions7.5.1 DirectDriveMARCoThe direct take-over of a locomotive by a controller on a control desk without the need to enterthe locomotive address is known as DirectDrive. This simple and convenient method oflocomotive control can be used in combination of MARCo with a number of <strong>Uhlenbrock</strong> controldesks.The prerequisite for DirectDrive is that the MARCo-Receiver is setup so that it sends the<strong>Uhlenbrock</strong> data format. For this LNCV 15 must have a Value 1 or 9 (more about LNCV 15 inChap. 7.6). Then the MARCo-Receiver sends all locomotive information via the LocoNet, assoon as a locomotive arrives at the Detector. The controllers connected to the LocoNet canthen support locomotive selection with the DirectDrive Function.7.5.1.1 DirectDrive and Intellibox/IB-ControlThe Intellibox MARCo Mode (from Software Version 1.55) can be selected by multipleoperation of the [mode]-key or pressing the [mode] and [6] in quick succession. The middle ofthe display changes to match the selected mode.NOTE: Even though the mode here is known as LISSY-Mode, it functions in exactly the sameway, with the information transmitted by the MARCo-Receiver.If the LISSY Mode is selected the MARCo-Receiver can be monitored in the middle part of thedisplay:In the display represented above it shows that the monitored receiver was passed by alocomotive with address 234 in the direction indicated by the arrow. The 2 shown after thedash is the train category. If the monitored point is passed by a wagon with a MARCotransmitter it is indicated in the display with a W:For a MARCo-Receiver in a vacant block section the middle section of the display is cleared.If a locomotive is reported by MARCo Receiver, as shown in the middle part of the displays,then this locomotive can be taken over one of the two controllers on the Intellibox. For this youpress the []-key to take over the locomotive on the left controller and the []-key, to takeover the locomotive on the right controller.7.5.1.2 DirectDrive and Track-ControlThe TrackControl Speed Controller 69 300 similarly supports the DirectDrive Function. Assoon as a locomotive passes the MARCo Receiver’s Detector which is assigned to thecontroller the LED above the [lok#]-key blinks “green”. Now only the [lok#]-key needs to bepressed once and the locomotive is taken over by the controller.Also every TrackControl Signal module 69 230 can have a MARCo-Receiver assigned to itusing LocoNet programming. For this, LNCV 37 of the signal module must be assigned withthe MARCo Receiver’s module address. If this is done, the signal module remembers thelocomotive which last passed the detector of the assigned MARCo Receiver. If now the buttonon the signal module is pressed at the same time as the [lok#]-key on the controller 69 300,the locomotive which last passed the detector is taken over. This way you take control of trains69
Page 3:
Table of Contents3MARCo1. MARCo - M
Page 6 and 7:
1.2 How MARCo operatesMARCoMARCo is
Page 8 and 9:
2.2 Installation of MARCo-Receiver
Page 10 and 11:
3. MARCo transmitterMARCoMARCo infr
Page 12 and 13:
3.4 Train categoriesMARCoWith the I
Page 14 and 15:
MARCoNOTE: If multiple boosters are
Page 16 and 17:
MARCoIf the cursor flashes in the L
Page 18 and 19: MARCo4.4.2 Programming with an Inte
Page 20 and 21: MARCo• If you with to change the
Page 22 and 23: MARCo• Press the “Prog.mode on
Page 24 and 25: 6. First applicationsMARCoIn this c
Page 26 and 27: MARCoProgram the following LNCVs as
Page 28 and 29: 7.2.1 Reporting train number and ca
Page 30 and 31: 7.3.1 General instruction descripti
Page 32 and 33: 86 3 address Address matches: imple
Page 34 and 35: MARCoComputation of the command val
Page 36 and 37: Allocation of the LNCVs for speed i
Page 38 and 39: 38MARCoMethod:Call up the LocoNet P
Page 40 and 41: MARCoNOTE: In a normal switching op
Page 42 and 43: MARCoIn order to set up this sequen
Page 44 and 45: MARCoIn order to setup the example
Page 46 and 47: MARCoExampleA MARCo-Receiver with t
Page 48 and 49: MARCoIn order to setup this operati
Page 50 and 51: MARCoThe entry manager ensures that
Page 52 and 53: 52MARCoLNCV Description60 Station t
Page 54 and 55: MARCoExtended operation: Solenoids
Page 56 and 57: MARCoCoordination with the entry ma
Page 58 and 59: MARCoThe passing loop can be utiliz
Page 60 and 61: MARCoExample 1: 3-Track Station con
Page 62 and 63: MARCoAdditional Programming of MARC
Page 64 and 65: LNCV Description20 Track 1: Address
Page 66 and 67: MARCoProcessing the instructions of
Page 70 and 71: MARCothat are stopped at a red sign
Page 72 and 73: MARCoLNCV Description10 Block optio
Page 74 and 75: MARCoWaiting time to the next Autom
Page 76 and 77: 8.5 MARCo and Fleischmann TwinCente
Page 78 and 79: MARCoA.1 MARCO transmitter 68320 Co
Page 80 and 81: MARCo13 Meaning of the LNCV, if LNC
Page 82 and 83: MARCoA.3 MARCo-Receiver Factory def
Page 84 and 85: A.5 Route Table for the Intellibox
Page 86 and 87: MARCoMARCo-Receiver No.Configuratio
Page 88 and 89: MARCoExamples88
Page 90 and 91: MARCoComputation of command options
Page 92 and 93: Feedback from when passing a Track
Page 94 and 95: MARCoProgramming of function instru
Page 96 and 97: 96MARCo
Page 98 and 99: MARCoBasic programming of MARCo-Rec
Page 100 and 101: MARCoProgramming of the MARCo-Recei
Page 102 and 103: MARCoExtension to an automatically
Page 104 and 105: MARCoComputation of command option
Page 106: Authors: Dr.-Ing. T. Vaupel, D. Ric
show all

Untitled - Uhlenbrock

Create successful ePaper yourself

Delete template?

Save as template?