CONELOG® Implant System Prosthetic Restorations - Camlog

More documents

Recommendations

Info

CONELOG ® IMPLANT SYSTEM PROSTHETIC RESTORATIONS CONELOG ® BAR ABUTMENT AFTER IMPRESSION TAKING IN THE CONELOG ® IMPLANT INSERTING THE CONELOG ® BAR ABUTMENTS IN THE WORKING CAST The dental technician selects the appropriate CONELOG ® bar abutments according to the CONELOG ® implant diameter used (note color-coding) and the specific gingival heights and inserts them into the CONELOG ® lab analogs. The CONELOG ® bar abutments are inserted into the driver for bar abutments. A screw integrated in the instrument secures the abutment. The screw is tightened by hand. The driver is used to tighten the CONELOG ® bar abutments by hand. The bar abutment plateau should be approx. 0.5 mm supragingival. IMPORTANT NOTE The bar abutments must not be modified! The bar is fabricated on the cast. A previously prepared silicone index is used to virtually represent the space available in the planning and fabrication of the bar construction. 110 Driver for bar abutment Ø 3.3/3.8/4.3/5.0 mm Finished working cast with CONELOG ® Bar abutments Working cast with silicone index 0.5 mm
FABRICATION OF THE BAR CONSTRUCTION CAST BAR CONSTRUCTIONS Various bar bases are available for bar fabrication using casting technology: FULL CASTING TECHNIQUE BASE FOR BAR ABUTMENT, BURN-OUT Fabrication of a cast bar construction with prefabricated bar base made of burn-out plastic (POM) for full casting technique. A prosthetic screw for bar abutment (hex) based on the diameter is used to fix the bar base on the CONELOG ® bar abutment. CAUTION! To avoid deforming the bar base, only tighten the prosthetic screw lightly by hand. The bar base can be shortened occlusally to the height of the screwed prosthetic screw. The overall height of the base is 14 mm. EXAMPLE: WORKING CAST WITH CONELOG ® LAB ANALOGS (TITANIUM ALLOY). WAX-UP The bar wax-up is created based on the planning on the burn-out bar base directly. The wax thickness over the plastic coping should be at least 0.3 mm. Do not cover the delicate edge of the base with wax. Prefabricated bar components made of wax / plastic can also be used to fabricate a premilled bar construction. IMPORTANT NOTE When burning out the casting muffle, swelling may occur due to the thermal expansion of the plastic and damage the investment compound in the area of the plastic base. This can cause investment compound to be included in the casting metal. Therefore, a minimum wax thickness of 0.3 mm should be applied to the plastic base. When heating, the wax softens first and gives the plastic enough space to expand. Base for bar abutment, burn-out, with prosthetic screw Example: Milled bar construction Screw-retained base on the CONELOG ® Bar abutment CONELOG ® IMPLANT SYSTEM PROSTHETIC RESTORATIONS Base for CONELOG ® ART. NO. ARTICLE MATERIAL C2257.3300 bar abutment, burn-out, for Ø 3.3/3.8/4.3/5.0 mm POM POM: Polyoxymethylene 111
Page 1 and 2:
CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 3 and 4:
TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6:
SYSTEM INTRODUCTION GENERAL GUIDELI
Page 7 and 8:
CONELOG ® IMPLANT/BAR ABUTMENT/ BA
Page 9 and 10:
CONELOG ® Screw design CONELOG ®
Page 11 and 12:
COLOR-CODING CONELOG ® IMPLANT SYS
Page 13 and 14:
SILICONE INDEX The silicone index i
Page 15 and 16:
ABUTMENT SELECTION In consideration
Page 17 and 18:
IMPORTANT NOTE Because of the conic
Page 19 and 20:
CONELOG ® CONELOG Impression posts
Page 21 and 22:
CONELOG ® IMPRESSION POST INSERTIO
Page 23 and 24:
CLOSED TRAY IMPRESSION-TAKING METHO
Page 25 and 26:
CONELOG ® CAST FABRICATION STANDAR
Page 27 and 28:
Page 29 and 30:
CONELOG ® BITE REGISTRATION POSTS
Page 31 and 32:
Remove the bite register, the bite
Page 33 and 34:
CONELOG ® TEMPORARY RESTORATION CO
Page 35 and 36:
After customizing and covering with
Page 37 and 38:
CONELOG ® ESTHOMIC ® ABUTMENTS, S
Page 39 and 40:
CONELOG ® ESTHOMIC ® SELECTION AB
Page 41 and 42:
PREPARATION Abrasive wheels suitabl
Page 43 and 44:
TIP: So that the cast crown framewo
Page 45 and 46:
INDIVIDUAL PROCESSING/PREPARATION (
Page 47 and 48:
PREPARATION: The abutment heights a
Page 49 and 50:
CONELOG ® LOGFIT ® ABUTMENTS CONE
Page 51 and 52:
USE SELECTION AND INSERTION OF THE
Page 53 and 54:
LOGFIT ® CAST FABRICATION For cast
Page 55 and 56:
Page 57 and 58:
CONELOG ® GOLD-PLASTIC ABUTMENT CO
Page 59 and 60: CAUTION! Do not cover the fine gold
Page 61 and 62: DOUBLE CROWN RESTORATION WITH THE C
Page 63 and 64: CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 65 and 66: PROCESSING After casting, the CONEL
Page 67 and 68: CONELOG ® UNIVERSAL AND TELESCOPE
Page 69 and 70: PROCESSING THE CONELOG ® ABUTMENTS
Page 71 and 72: Follow the manufacturer's instructi
Page 73 and 74: CONELOG ® BONDING AID Using the CO
Page 75 and 76: CONELOG ® SCANBODY SCAN-TECHNICAL
Page 77 and 78: CONELOG ® VARIO SR ABUTMENTS CONEL
Page 79 and 80: VARIO SR PROSTHETIC COMPONENTS To f
Page 81 and 82: ABUTMENT INSERTION Clean the intern
Page 83 and 84: IMPRESSION TAKING WITH VARIO SR IMP
Page 85 and 86: IMPRESSION-TAKING FOR VARIO SR SING
Page 87 and 88: Once the register has been created,
Page 89 and 90: The impression is cast with suitabl
Page 91 and 92: CAST FABRICATION FOR SINGLE TOOTH R
Page 93 and 94: CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 95 and 96: OPTIONAL FABRICATION OF THE SUPERST
Page 97 and 98: VARIO SR ANTIROTATIONAL MECHANISMS
Page 99 and 100: After trimming, the cast object is
Page 101 and 102: The caps are then veneered and atta
Page 103 and 104: The bar elements are cut accordingl
Page 105 and 106: Gingival heights from the implant s
Page 107 and 108: For impression taking, the impressi
Page 109: The cast is fabricated in the usual
Page 113 and 114: SLEEVE FOR TITANIUM BONDING BASE BU
Page 115 and 116: CAST-ON TECHNIQUE BASE FOR BAR ABUT
Page 117 and 118: LASER-WELDED BAR CONSTRUCTION BASE
Page 119 and 120: The soldering is carried out accord
Page 121 and 122: PREPARING AND FABRICATING THE RELIN
Page 123 and 124: CONELOG ® BALL ABUTMENT SET FOR IM
Page 125 and 126: SETTING THE RETENTION FORCE With th
Page 127 and 128: DUPLICATING THE WORKING CAST After
Page 129 and 130: INSERTION OF THE CONELOG ® BALL AB
Page 131 and 132: After the impression is taken succe
Page 133 and 134: RELINING OF A BALL ABUTMENT-RETAINE
Page 135 and 136: CONELOG ® LOCATOR ® ABUTMENT PROD
Page 137 and 138: LOCATOR ® SYSTEM COMPONENTS ART. N
Page 139 and 140: FABRICATION OF A NEW LOCATOR ® -RE
Page 141 and 142: INTEGRATION OF THE COLORED REPLACEM
Page 143 and 144: Titanium housing with black process
Page 145 and 146: RELINING OF A LOCATOR ® -RETAINED
Page 147 and 148: MATERIALS CONELOG ® IMPLANT SYSTEM
Page 149 and 150: FURTHER DOCUMENTATION Further infor
Page 152:
HEADQUARTERS CAMLOG Biotechnologies
show all

CONELOG® Implant System Prosthetic Restorations - Camlog

Create successful ePaper yourself

Delete template?

Save as template?