CONELOG® Implant System Prosthetic Restorations - Camlog

More documents

Recommendations

Info

CONELOG ® IMPLANT SYSTEM PROSTHETIC RESTORATIONS CONELOG ® LOGFIT ® PROSTHETIC SYSTEM INVESTMENT, CAST AND DEVESTMENT The abutment is embedded according to the instruction manual of the muffle system used. We do not recommend the use of wax wetting agents. However, if wax wetting agents are used, it must be suitable for use with POM plastic components. When embedding, the correct placement of the wax-up in the casting muffle is of importance. Volume ratios and pin angles must be selected so that the required temperature for casting is achieved. This is particularly important for voluminous casts. We recommend phosphate bound investment materials. The manufacturer›s processing instructions must be observed and the mixing ratios and preheating times accurately observed. We recommend you do not use any quick heating processes (speed investment compounds). The cast delay time must be kept as brief as possible. After casting, the cast object must be slowly cooled to room temperature and the object gently devested. We recommend gentle devestment in an ultrasonic bath with waterjet or stripping. After trimming, the cast object is prepared for ceramic veneering. The ceramic to be used must be compatible with the alloy (observe heat expansion coefficient). The occlusal surface should be designed based on the «Freedom in centric» concept. 56 INSERTION AND CEMENTING OF THE PROSTHETIC RESTORATION Clean and disinfect the prosthetic components prior to insertion. We recommend component sterilization (see also the «Preparation Instructions for the CAMLOG ® /CONELOG ® Implant System», Art. No. J8000.0032). The peri-implant hard and soft tissue situation must allow gapless insertion of the restoration on the CONELOG ® Logfit ® abutment. We recommend phosphate and carboxylate cements for the final cementation. Manufacture instructions must be observed. To avoid an air cushion, only a thin layer of cement should be brushed into the restoration. IMPORTANT NOTE Cement residues in the sulcus must be carefully removed.
CONELOG ® GOLD-PLASTIC ABUTMENT CONELOG ® GOLD-PLASTIC ABUTMENT The CONELOG ® gold-plastic abutment consists of a prefabricated cast-on base part made of a high-melting cast-on gold alloy and a screw channel made of burn-out plastic (POM). The screw channel represents a modeling aid and ensure a clean finish of the screw channel. The screw channel is color-coded, firmly connected to the base part and can be individually shortened occlusally. The CONELOG ® gold-plastic abutment can be used to fabricate singlecrowns, individual implant abutments (mesostructures) for cementable bridge restorations and primary abutments for bridging implant axis divergences in the telescopic crown technique using the cast-on technique. The high-melting cast-on gold alloy is only suitable for the cast-on procedure with high-gold alloys. The prosthetic height (PH) is the distance between the implant shoulder surface up to the occlusal abutment edge of the CONELOG ® abutment screwed into the CONELOG ® implant. Plastic screw channel Cast-on base part Prosthetic height CONELOG ® IMPLANT SYSTEM PROSTHETIC RESTORATIONS CONELOG ® Abutment screw CONELOG ® GOLD-PLASTIC ABUTMENT, cast-on, incl. CONELOG ® Abutment screw ART. NO. C2246.3300 C2246.3800 C2246.4300 C2246.5000 PH: Prosthetic height (measured from the implant shoulder surface to occlusal abutment edge with the CONELOG ® abutment screwed into the CONELOG ® Implant Ø mm 3.3 3.8 4.3 5.0 PH mm 11.75 11.75 11.75 11.75 implant) 57
Page 1 and 2:
CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 3 and 4:
TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6: SYSTEM INTRODUCTION GENERAL GUIDELI
Page 7 and 8: CONELOG ® IMPLANT/BAR ABUTMENT/ BA
Page 9 and 10: CONELOG ® Screw design CONELOG ®
Page 11 and 12: COLOR-CODING CONELOG ® IMPLANT SYS
Page 13 and 14: SILICONE INDEX The silicone index i
Page 15 and 16: ABUTMENT SELECTION In consideration
Page 17 and 18: IMPORTANT NOTE Because of the conic
Page 19 and 20: CONELOG ® CONELOG Impression posts
Page 21 and 22: CONELOG ® IMPRESSION POST INSERTIO
Page 23 and 24: CLOSED TRAY IMPRESSION-TAKING METHO
Page 25 and 26: CONELOG ® CAST FABRICATION STANDAR
Page 27 and 28: CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 29 and 30: CONELOG ® BITE REGISTRATION POSTS
Page 31 and 32: Remove the bite register, the bite
Page 33 and 34: CONELOG ® TEMPORARY RESTORATION CO
Page 35 and 36: After customizing and covering with
Page 37 and 38: CONELOG ® ESTHOMIC ® ABUTMENTS, S
Page 39 and 40: CONELOG ® ESTHOMIC ® SELECTION AB
Page 41 and 42: PREPARATION Abrasive wheels suitabl
Page 43 and 44: TIP: So that the cast crown framewo
Page 45 and 46: INDIVIDUAL PROCESSING/PREPARATION (
Page 47 and 48: PREPARATION: The abutment heights a
Page 49 and 50: CONELOG ® LOGFIT ® ABUTMENTS CONE
Page 51 and 52: USE SELECTION AND INSERTION OF THE
Page 53 and 54: LOGFIT ® CAST FABRICATION For cast
Page 55: CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 59 and 60: CAUTION! Do not cover the fine gold
Page 61 and 62: DOUBLE CROWN RESTORATION WITH THE C
Page 65 and 66: PROCESSING After casting, the CONEL
Page 67 and 68: CONELOG ® UNIVERSAL AND TELESCOPE
Page 69 and 70: PROCESSING THE CONELOG ® ABUTMENTS
Page 71 and 72: Follow the manufacturer's instructi
Page 73 and 74: CONELOG ® BONDING AID Using the CO
Page 75 and 76: CONELOG ® SCANBODY SCAN-TECHNICAL
Page 77 and 78: CONELOG ® VARIO SR ABUTMENTS CONEL
Page 79 and 80: VARIO SR PROSTHETIC COMPONENTS To f
Page 81 and 82: ABUTMENT INSERTION Clean the intern
Page 83 and 84: IMPRESSION TAKING WITH VARIO SR IMP
Page 85 and 86: IMPRESSION-TAKING FOR VARIO SR SING
Page 87 and 88: Once the register has been created,
Page 89 and 90: The impression is cast with suitabl
Page 91 and 92: CAST FABRICATION FOR SINGLE TOOTH R
Page 95 and 96: OPTIONAL FABRICATION OF THE SUPERST
Page 97 and 98: VARIO SR ANTIROTATIONAL MECHANISMS
Page 99 and 100: After trimming, the cast object is
Page 101 and 102: The caps are then veneered and atta
Page 103 and 104: The bar elements are cut accordingl
Page 105 and 106: Gingival heights from the implant s
Page 107 and 108:
For impression taking, the impressi
Page 109 and 110:
The cast is fabricated in the usual
Page 111 and 112:
FABRICATION OF THE BAR CONSTRUCTION
Page 113 and 114:
SLEEVE FOR TITANIUM BONDING BASE BU
Page 115 and 116:
CAST-ON TECHNIQUE BASE FOR BAR ABUT
Page 117 and 118:
LASER-WELDED BAR CONSTRUCTION BASE
Page 119 and 120:
The soldering is carried out accord
Page 121 and 122:
PREPARING AND FABRICATING THE RELIN
Page 123 and 124:
CONELOG ® BALL ABUTMENT SET FOR IM
Page 125 and 126:
SETTING THE RETENTION FORCE With th
Page 127 and 128:
DUPLICATING THE WORKING CAST After
Page 129 and 130:
INSERTION OF THE CONELOG ® BALL AB
Page 131 and 132:
After the impression is taken succe
Page 133 and 134:
RELINING OF A BALL ABUTMENT-RETAINE
Page 135 and 136:
CONELOG ® LOCATOR ® ABUTMENT PROD
Page 137 and 138:
LOCATOR ® SYSTEM COMPONENTS ART. N
Page 139 and 140:
FABRICATION OF A NEW LOCATOR ® -RE
Page 141 and 142:
INTEGRATION OF THE COLORED REPLACEM
Page 143 and 144:
Titanium housing with black process
Page 145 and 146:
RELINING OF A LOCATOR ® -RETAINED
Page 147 and 148:
MATERIALS CONELOG ® IMPLANT SYSTEM
Page 149 and 150:
FURTHER DOCUMENTATION Further infor
Page 152:
HEADQUARTERS CAMLOG Biotechnologies
show all

CONELOG® Implant System Prosthetic Restorations - Camlog

Create successful ePaper yourself

Delete template?

Save as template?