CONELOG® Implant System Prosthetic Restorations - Camlog

More documents

Recommendations

Info

CONELOG ® IMPLANT SYSTEM PROSTHETIC RESTORATIONS CONELOG ® VARIO SR ABUTMENTS TEMPORARY RESTORATIONS VARIO SR PROTECTION CAPS Vario SR protection caps can be used for the initial restoration as the final prosthetic restoration is being fabricated. Vario SR protection caps are made of titanium alloy, are one piece, sterile packed and each available in 3.8/4.3 mm and 5.0 mm diameters. ART. NO. ARTICLE IMPLANT Ø MM J2568.4300 Vario SR 3.8/4.3 protection cap J2568.6000 Vario SR 5.0 protection cap Vario SR protection caps are screwed directly onto the CONELOG ® Vario SR abutments (straight and angled) attached definitively to the CONELOG ® implant. The caps are picked up with a screwdriver (hex) and screwed in hand-tightened. 92 NOTE If an existing prosthesis is used as a temporary restoration, it must be hollow ground in the areas of the Vario SR protection caps. The prosthesis must not lie on the Vario SR protection caps and thus compromise implant healing by transferring mastication forces. Height 6.0 mm IMPORTANT NOTE During intraoral use, products must be secured in general against aspiration and swallowing.
CONELOG ® IMPLANT SYSTEM PROSTHETIC RESTORATIONS TEMPORARY BRIDGE RESTORATIONS VARIO SR TITANIUM CAPS Vario SR titanium caps are attached to the already inserted Vario SR abutments (straight/angled). They are equipped with a retention surface on the outside for coating with plastic. The caps are made of titanium alloy and are each available in the 3.8/4.3 mm and 5.0 mm diameters. NOTE Vario SR titanium caps, bridge, have no antirotational mechanism and therefore are only suited for bridge restorations. ART. NO. ARTICLE IMPLANT Ø MM J2564.4301 Vario SR titanium cap, 3.8/4.3 bridge, incl. Vario SR prosthetic screw J2564.6001 Vario SR titanium cap, 5.0 bridge, incl. Vario SR prosthetic screw J4005.2004 Vario SR prosthetic screw, hex, M 2.0, yellow anodized Information about fabricating a temporary bridge restoration is available on page 100. 93
Page 1 and 2:
CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 3 and 4:
TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6:
SYSTEM INTRODUCTION GENERAL GUIDELI
Page 7 and 8:
CONELOG ® IMPLANT/BAR ABUTMENT/ BA
Page 9 and 10:
CONELOG ® Screw design CONELOG ®
Page 11 and 12:
COLOR-CODING CONELOG ® IMPLANT SYS
Page 13 and 14:
SILICONE INDEX The silicone index i
Page 15 and 16:
ABUTMENT SELECTION In consideration
Page 17 and 18:
IMPORTANT NOTE Because of the conic
Page 19 and 20:
CONELOG ® CONELOG Impression posts
Page 21 and 22:
CONELOG ® IMPRESSION POST INSERTIO
Page 23 and 24:
CLOSED TRAY IMPRESSION-TAKING METHO
Page 25 and 26:
CONELOG ® CAST FABRICATION STANDAR
Page 27 and 28:
CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 29 and 30:
CONELOG ® BITE REGISTRATION POSTS
Page 31 and 32:
Remove the bite register, the bite
Page 33 and 34:
CONELOG ® TEMPORARY RESTORATION CO
Page 35 and 36:
After customizing and covering with
Page 37 and 38:
CONELOG ® ESTHOMIC ® ABUTMENTS, S
Page 39 and 40:
CONELOG ® ESTHOMIC ® SELECTION AB
Page 41 and 42: PREPARATION Abrasive wheels suitabl
Page 43 and 44: TIP: So that the cast crown framewo
Page 45 and 46: INDIVIDUAL PROCESSING/PREPARATION (
Page 47 and 48: PREPARATION: The abutment heights a
Page 49 and 50: CONELOG ® LOGFIT ® ABUTMENTS CONE
Page 51 and 52: USE SELECTION AND INSERTION OF THE
Page 53 and 54: LOGFIT ® CAST FABRICATION For cast
Page 55 and 56: CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 57 and 58: CONELOG ® GOLD-PLASTIC ABUTMENT CO
Page 59 and 60: CAUTION! Do not cover the fine gold
Page 61 and 62: DOUBLE CROWN RESTORATION WITH THE C
Page 63 and 64: CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 65 and 66: PROCESSING After casting, the CONEL
Page 67 and 68: CONELOG ® UNIVERSAL AND TELESCOPE
Page 69 and 70: PROCESSING THE CONELOG ® ABUTMENTS
Page 71 and 72: Follow the manufacturer's instructi
Page 73 and 74: CONELOG ® BONDING AID Using the CO
Page 75 and 76: CONELOG ® SCANBODY SCAN-TECHNICAL
Page 77 and 78: CONELOG ® VARIO SR ABUTMENTS CONEL
Page 79 and 80: VARIO SR PROSTHETIC COMPONENTS To f
Page 81 and 82: ABUTMENT INSERTION Clean the intern
Page 83 and 84: IMPRESSION TAKING WITH VARIO SR IMP
Page 85 and 86: IMPRESSION-TAKING FOR VARIO SR SING
Page 87 and 88: Once the register has been created,
Page 89 and 90: The impression is cast with suitabl
Page 91: CAST FABRICATION FOR SINGLE TOOTH R
Page 95 and 96: OPTIONAL FABRICATION OF THE SUPERST
Page 97 and 98: VARIO SR ANTIROTATIONAL MECHANISMS
Page 99 and 100: After trimming, the cast object is
Page 101 and 102: The caps are then veneered and atta
Page 103 and 104: The bar elements are cut accordingl
Page 105 and 106: Gingival heights from the implant s
Page 107 and 108: For impression taking, the impressi
Page 109 and 110: The cast is fabricated in the usual
Page 111 and 112: FABRICATION OF THE BAR CONSTRUCTION
Page 113 and 114: SLEEVE FOR TITANIUM BONDING BASE BU
Page 115 and 116: CAST-ON TECHNIQUE BASE FOR BAR ABUT
Page 117 and 118: LASER-WELDED BAR CONSTRUCTION BASE
Page 119 and 120: The soldering is carried out accord
Page 121 and 122: PREPARING AND FABRICATING THE RELIN
Page 123 and 124: CONELOG ® BALL ABUTMENT SET FOR IM
Page 125 and 126: SETTING THE RETENTION FORCE With th
Page 127 and 128: DUPLICATING THE WORKING CAST After
Page 129 and 130: INSERTION OF THE CONELOG ® BALL AB
Page 131 and 132: After the impression is taken succe
Page 133 and 134: RELINING OF A BALL ABUTMENT-RETAINE
Page 135 and 136: CONELOG ® LOCATOR ® ABUTMENT PROD
Page 137 and 138: LOCATOR ® SYSTEM COMPONENTS ART. N
Page 139 and 140: FABRICATION OF A NEW LOCATOR ® -RE
Page 141 and 142: INTEGRATION OF THE COLORED REPLACEM
Page 143 and 144:
Titanium housing with black process
Page 145 and 146:
RELINING OF A LOCATOR ® -RETAINED
Page 147 and 148:
MATERIALS CONELOG ® IMPLANT SYSTEM
Page 149 and 150:
FURTHER DOCUMENTATION Further infor
Page 152:
HEADQUARTERS CAMLOG Biotechnologies
show all

CONELOG® Implant System Prosthetic Restorations - Camlog

Create successful ePaper yourself

Delete template?

Save as template?