CONELOG® Implant System Prosthetic Restorations - Camlog

More documents

Recommendations

Info

CONELOG ® IMPLANT SYSTEM PROSTHETIC RESTORATIONS CONELOG ® IMPRESSION TAKING OPEN-TRAY IMPRESSION-TAKING METHOD The open-tray impression-taking method requires a custom-made impression tray that is perforated for the protrusion of the fixing screw extending from the implant axis. CONELOG ® Impression posts, open tray The fixing screw is secured in the CONELOG ® impression post with an O-ring and must only be tightened by hand using the screwdriver, hex, both in the CONELOG ® implant as well as in the CONELOG ® lab analog. 20 NOTE Before removing the impression, the loosened screw must be withdrawn until you can feel the limit stop (O-ring). Otherwise the axis divergences of the implant can make removing the impression difficult or can deform the impression due to the high compression. Impressions can be taken with implant axis divergences of up to 20° (10° for each CONELOG ® implant). The fixing screw is equipped with a predetermined breaking point. If space limitations are encountered, it can be shortened by 3.0 mm by breaking it off with a screwdriver, hex. Caution: Shorten extra-orally only! IMPORTANT NOTE During intraoral use, products must be secured in general against aspiration and swallowing. 3.0 mm O-ring <strong>Prosthetic</strong> height 10.0 mm O-ring
CONELOG ® IMPRESSION POST INSERTION The healing cap or temporary restoration is removed. The impression post open-tray is placed on the implant and the fixing screw is gently tightened. The impression post is rotation-symmetrical and does not require any specific orientation. Carefully rotate the impression post in the implant until the cams engage with the grooves of the implant. Tighten the fixing screw manually with the screwdriver, hex. We recommend taking an x-ray to check that the impression post is seated correctly before taking the impression, particularly where gingiva is tight and thick. CONELOG ® IMPLANT SYSTEM PROSTHETIC RESTORATIONS CAUTION! Height difference if cams are not snapped into place is approx. 0.6 mm! 21
Page 1 and 2: CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 3 and 4: TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6: SYSTEM INTRODUCTION GENERAL GUIDELI
Page 7 and 8: CONELOG ® IMPLANT/BAR ABUTMENT/ BA
Page 9 and 10: CONELOG ® Screw design CONELOG ®
Page 11 and 12: COLOR-CODING CONELOG ® IMPLANT SYS
Page 13 and 14: SILICONE INDEX The silicone index i
Page 15 and 16: ABUTMENT SELECTION In consideration
Page 17 and 18: IMPORTANT NOTE Because of the conic
Page 19: CONELOG ® CONELOG Impression posts
Page 23 and 24: CLOSED TRAY IMPRESSION-TAKING METHO
Page 25 and 26: CONELOG ® CAST FABRICATION STANDAR
Page 29 and 30: CONELOG ® BITE REGISTRATION POSTS
Page 31 and 32: Remove the bite register, the bite
Page 33 and 34: CONELOG ® TEMPORARY RESTORATION CO
Page 35 and 36: After customizing and covering with
Page 37 and 38: CONELOG ® ESTHOMIC ® ABUTMENTS, S
Page 39 and 40: CONELOG ® ESTHOMIC ® SELECTION AB
Page 41 and 42: PREPARATION Abrasive wheels suitabl
Page 43 and 44: TIP: So that the cast crown framewo
Page 45 and 46: INDIVIDUAL PROCESSING/PREPARATION (
Page 47 and 48: PREPARATION: The abutment heights a
Page 49 and 50: CONELOG ® LOGFIT ® ABUTMENTS CONE
Page 51 and 52: USE SELECTION AND INSERTION OF THE
Page 53 and 54: LOGFIT ® CAST FABRICATION For cast
Page 57 and 58: CONELOG ® GOLD-PLASTIC ABUTMENT CO
Page 59 and 60: CAUTION! Do not cover the fine gold
Page 61 and 62: DOUBLE CROWN RESTORATION WITH THE C
Page 65 and 66: PROCESSING After casting, the CONEL
Page 67 and 68: CONELOG ® UNIVERSAL AND TELESCOPE
Page 69 and 70: PROCESSING THE CONELOG ® ABUTMENTS
Page 71 and 72:
Follow the manufacturer's instructi
Page 73 and 74:
CONELOG ® BONDING AID Using the CO
Page 75 and 76:
CONELOG ® SCANBODY SCAN-TECHNICAL
Page 77 and 78:
CONELOG ® VARIO SR ABUTMENTS CONEL
Page 79 and 80:
VARIO SR PROSTHETIC COMPONENTS To f
Page 81 and 82:
ABUTMENT INSERTION Clean the intern
Page 83 and 84:
IMPRESSION TAKING WITH VARIO SR IMP
Page 85 and 86:
IMPRESSION-TAKING FOR VARIO SR SING
Page 87 and 88:
Once the register has been created,
Page 89 and 90:
The impression is cast with suitabl
Page 91 and 92:
CAST FABRICATION FOR SINGLE TOOTH R
Page 93 and 94:
CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 95 and 96:
OPTIONAL FABRICATION OF THE SUPERST
Page 97 and 98:
VARIO SR ANTIROTATIONAL MECHANISMS
Page 99 and 100:
After trimming, the cast object is
Page 101 and 102:
The caps are then veneered and atta
Page 103 and 104:
The bar elements are cut accordingl
Page 105 and 106:
Gingival heights from the implant s
Page 107 and 108:
For impression taking, the impressi
Page 109 and 110:
The cast is fabricated in the usual
Page 111 and 112:
FABRICATION OF THE BAR CONSTRUCTION
Page 113 and 114:
SLEEVE FOR TITANIUM BONDING BASE BU
Page 115 and 116:
CAST-ON TECHNIQUE BASE FOR BAR ABUT
Page 117 and 118:
LASER-WELDED BAR CONSTRUCTION BASE
Page 119 and 120:
The soldering is carried out accord
Page 121 and 122:
PREPARING AND FABRICATING THE RELIN
Page 123 and 124:
CONELOG ® BALL ABUTMENT SET FOR IM
Page 125 and 126:
SETTING THE RETENTION FORCE With th
Page 127 and 128:
DUPLICATING THE WORKING CAST After
Page 129 and 130:
INSERTION OF THE CONELOG ® BALL AB
Page 131 and 132:
After the impression is taken succe
Page 133 and 134:
RELINING OF A BALL ABUTMENT-RETAINE
Page 135 and 136:
CONELOG ® LOCATOR ® ABUTMENT PROD
Page 137 and 138:
LOCATOR ® SYSTEM COMPONENTS ART. N
Page 139 and 140:
FABRICATION OF A NEW LOCATOR ® -RE
Page 141 and 142:
INTEGRATION OF THE COLORED REPLACEM
Page 143 and 144:
Titanium housing with black process
Page 145 and 146:
RELINING OF A LOCATOR ® -RETAINED
Page 147 and 148:
MATERIALS CONELOG ® IMPLANT SYSTEM
Page 149 and 150:
FURTHER DOCUMENTATION Further infor
Page 152:
HEADQUARTERS CAMLOG Biotechnologies
show all

CONELOG® Implant System Prosthetic Restorations - Camlog

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?