CONELOG® Implant System Prosthetic Restorations - Camlog

More documents

Recommendations

Info

CONELOG ® IMPLANT SYSTEM PROSTHETIC RESTORATIONS CONELOG ® VARIO SR ABUTMENTS APPLICATION SELECTION AND INSERTION OF THE CONELOG ® VARIO SR ABUTMENTS The suitable CONELOG ® Vario SR abutment can be selected depending on the clinical situation for bridge and bar constructions on the patient directly. CONELOG ® Vario SR abutments are sterile packed incl. the enclosed abutment screw. Sterilization of the abutment as recommended before insertion is not required for immediate final integration and when the abutments remain in the CONELOG ® implant. CONELOG ® Insertion post CONELOG ® <strong>Implant</strong> The angle of the Vario SR aligning tools is identical to the 20° and 30° angled CONELOG ® Vario SR abutments. 80 Vario SR aligning tool The angle points in the opposite direction of the implant groove. SELECTING ANGLED CONELOG ® VARIO SR ABUTMENTS WITH THE ALIGNING TOOLS 20°/30° After inserting the implant, the Vario SR 20° and 30° aligning tools can be used when multiple CONELOG ® implants are placed to check the respective insertion direction and alignment of the implant grooves before inserting the CONELOG ® Vario SR abutments. The respective aligning tool is simply placed over the insertion post attached to the implant. If necessary, the user can slightly adjust the alignment of the grooves of the inner implant configuration. The Vario SR aligning tools are packed sterile. Vario SR aligning tool 20° Vario SR aligning tool and angled CONELOG ® Vario SR abutment 20° Vario SR aligning tool 30° 2 chamfer = 20° 3 chamfer = 30° Vario SR aligning tool and angled CONELOG ® Vario SR abutment 30° IMPORTANT NOTE During intraoral use, products must be secured in general against aspiration and swallowing.
ABUTMENT INSERTION Clean the internal configuration of the implant before inserting the abutment. The selected CONELOG ® Vario SR abutment is inserted in the CONELOG ® implant and rotated until tactile engagement of the cams in the grooves of the implant. The abutment is then in the final position. ATTENTION: MAKE SURE THAT THE ABUTMENT SCREW TYPES MATCH! • Straight CONELOG ® Vario SR abutments = use CONELOG ® Vario SR abutment screws • Angled CONELOG ® Vario SR abutments (20° and 30°) = use CONELOG ® abutment screws A screwdriver (hex) and torque wrench are used to tighten the abutment screw with a torque of 20 Ncm. To achieve maximum pre-tension on the screws, the abutment screw should be retightened with the same torque after approx. 5 minutes. IMPORTANT NOTE The special design of the CONELOG ® Vario SR abutment screw and the CONELOG ® Vario SR lab screw for the straight CONELOG ® V ario SR abutment requires the sole use of the screwdriver, hex, Art. No. J5316.0501/0502/0503/0504/0510! We recommend taking a control x-ray to make sure the abutment is correctly seated on the implant. IMPORTANT NOTE CONELOG ® Vario SR abutments may not be modified. This would compromise the matched shape of the Vario SR prosthetic components. Screwdriver (hex) and torque wrench with continuous torque adjustment Screwdriver, hex, extra short, short, long CONELOG ® IMPLANT SYSTEM PROSTHETIC RESTORATIONS 20 Ncm 81
Page 1 and 2:
CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 3 and 4:
TABLE OF CONTENTS GENERAL SYSTEM IN
Page 5 and 6:
SYSTEM INTRODUCTION GENERAL GUIDELI
Page 7 and 8:
CONELOG ® IMPLANT/BAR ABUTMENT/ BA
Page 9 and 10:
CONELOG ® Screw design CONELOG ®
Page 11 and 12:
COLOR-CODING CONELOG ® IMPLANT SYS
Page 13 and 14:
SILICONE INDEX The silicone index i
Page 15 and 16:
ABUTMENT SELECTION In consideration
Page 17 and 18:
IMPORTANT NOTE Because of the conic
Page 19 and 20:
CONELOG ® CONELOG Impression posts
Page 21 and 22:
CONELOG ® IMPRESSION POST INSERTIO
Page 23 and 24:
CLOSED TRAY IMPRESSION-TAKING METHO
Page 25 and 26:
CONELOG ® CAST FABRICATION STANDAR
Page 27 and 28:
CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 29 and 30: CONELOG ® BITE REGISTRATION POSTS
Page 31 and 32: Remove the bite register, the bite
Page 33 and 34: CONELOG ® TEMPORARY RESTORATION CO
Page 35 and 36: After customizing and covering with
Page 37 and 38: CONELOG ® ESTHOMIC ® ABUTMENTS, S
Page 39 and 40: CONELOG ® ESTHOMIC ® SELECTION AB
Page 41 and 42: PREPARATION Abrasive wheels suitabl
Page 43 and 44: TIP: So that the cast crown framewo
Page 45 and 46: INDIVIDUAL PROCESSING/PREPARATION (
Page 47 and 48: PREPARATION: The abutment heights a
Page 49 and 50: CONELOG ® LOGFIT ® ABUTMENTS CONE
Page 51 and 52: USE SELECTION AND INSERTION OF THE
Page 53 and 54: LOGFIT ® CAST FABRICATION For cast
Page 55 and 56: CONELOG ® IMPLANT SYSTEM PROSTHETI
Page 57 and 58: CONELOG ® GOLD-PLASTIC ABUTMENT CO
Page 59 and 60: CAUTION! Do not cover the fine gold
Page 61 and 62: DOUBLE CROWN RESTORATION WITH THE C
Page 65 and 66: PROCESSING After casting, the CONEL
Page 67 and 68: CONELOG ® UNIVERSAL AND TELESCOPE
Page 69 and 70: PROCESSING THE CONELOG ® ABUTMENTS
Page 71 and 72: Follow the manufacturer's instructi
Page 73 and 74: CONELOG ® BONDING AID Using the CO
Page 75 and 76: CONELOG ® SCANBODY SCAN-TECHNICAL
Page 77 and 78: CONELOG ® VARIO SR ABUTMENTS CONEL
Page 79: VARIO SR PROSTHETIC COMPONENTS To f
Page 83 and 84: IMPRESSION TAKING WITH VARIO SR IMP
Page 85 and 86: IMPRESSION-TAKING FOR VARIO SR SING
Page 87 and 88: Once the register has been created,
Page 89 and 90: The impression is cast with suitabl
Page 91 and 92: CAST FABRICATION FOR SINGLE TOOTH R
Page 95 and 96: OPTIONAL FABRICATION OF THE SUPERST
Page 97 and 98: VARIO SR ANTIROTATIONAL MECHANISMS
Page 99 and 100: After trimming, the cast object is
Page 101 and 102: The caps are then veneered and atta
Page 103 and 104: The bar elements are cut accordingl
Page 105 and 106: Gingival heights from the implant s
Page 107 and 108: For impression taking, the impressi
Page 109 and 110: The cast is fabricated in the usual
Page 111 and 112: FABRICATION OF THE BAR CONSTRUCTION
Page 113 and 114: SLEEVE FOR TITANIUM BONDING BASE BU
Page 115 and 116: CAST-ON TECHNIQUE BASE FOR BAR ABUT
Page 117 and 118: LASER-WELDED BAR CONSTRUCTION BASE
Page 119 and 120: The soldering is carried out accord
Page 121 and 122: PREPARING AND FABRICATING THE RELIN
Page 123 and 124: CONELOG ® BALL ABUTMENT SET FOR IM
Page 125 and 126: SETTING THE RETENTION FORCE With th
Page 127 and 128: DUPLICATING THE WORKING CAST After
Page 129 and 130: INSERTION OF THE CONELOG ® BALL AB
Page 131 and 132:
After the impression is taken succe
Page 133 and 134:
RELINING OF A BALL ABUTMENT-RETAINE
Page 135 and 136:
CONELOG ® LOCATOR ® ABUTMENT PROD
Page 137 and 138:
LOCATOR ® SYSTEM COMPONENTS ART. N
Page 139 and 140:
FABRICATION OF A NEW LOCATOR ® -RE
Page 141 and 142:
INTEGRATION OF THE COLORED REPLACEM
Page 143 and 144:
Titanium housing with black process
Page 145 and 146:
RELINING OF A LOCATOR ® -RETAINED
Page 147 and 148:
MATERIALS CONELOG ® IMPLANT SYSTEM
Page 149 and 150:
FURTHER DOCUMENTATION Further infor
Page 152:
HEADQUARTERS CAMLOG Biotechnologies
show all

CONELOG® Implant System Prosthetic Restorations - Camlog

Create successful ePaper yourself

Delete template?

Save as template?