ATM Option System Reference - Comtech EF Data

More documents

Recommendations

Info

<strong>ATM</strong> <strong>Option</strong> 5.3.14 NAT rule 5.3.15 NAT side Enables (YES) or disables (NO) Network Address Translation (NAT) on this PVC connection. Values: NO, YES Default: NO When the NAT enable parameter is set to YES, the following additional parameters are also available: PVC 1> NAT enable (def:NO) ? YES PVC 1> NAT rule (1-10) (def:) ? PVC 1> NAT side (def:INTERNAL) ? Console SNMP Text-based Config NAT rule atmpvcNatRule [atmpvc#] NatRule Selects the NAT rule or rules to be used to translate address information for traffic to and from this PVC connection. A rule defines the correspondence between internal IP addresses and external, globally unique NAT IP addresses. Select multiple rules by entering a comma between the rule numbers, for example: 1,3,4. Define all NAT rules with the SETUP/IP/NAT submenu. For details, refer to the chapter Network Address Translation (NAT) in the LAN Connection and IP Networks fascicle of this document series. Values: 1 - 10 Default: none Console SNMP Text-based Config NAT side atmpvcNatSide [atmpvc#] NatSide Determines which address realm this PVC connection is associated with, and where NAT is carried out. • INTERNAL: NAT is carried out on the internal side of the network. Select this value if the PVC connection is to equipment on the local side (the private network). • EXTERNAL: NAT is carried out on the external side of the network. Select this value if the PVC connection is to equipment on the remote side. Values: INTERNAL, EXTERNAL Default: INTERNAL 5-10 Memotec Inc.
5.3.16 IP RIP SE/PVC Configuration Parameters Console SNMP Text-based Config IP RIP atmpvcIpRip [atmpvc#] IpRip Enables or disables the Routing Information Protocol (RIP) on the PVC connection. Three settings are available to enable IP RIP: • V1: The PVC uses RIP Version 1. With this version the subnet mask for an IP address in a routing table entry is determined using the mask of the port on which the frame was received. • V2 BROADCAST: The PVC uses RIP Version 2 in Broadcast mode. In Version 2 a subnet mask is transmitted for each address contained in the RIP frame. In Broadcast mode each RIP V2 frame is sent with IP address 255.255.255.255, which permits routers running RIP Version 1 to receive and analyze those frames. • V2 MULTICAST: The PVC uses RIP Version 2 in Multicast mode. In this mode each RIP V2 frame is sent with IP address 224.000.000.009, which prevents routers running RIP Version 1 from receiving those frames. For details on the differences between IP RIP routing using RIP Version 1 and RIP Version 2, consult the Bridge Router Functions chapter of the LAN Connection and IP Networks fascicle of this document series. • Set the IP RIP parameter to DISABLE to prevent the NetPerformer from transmitting or receiving RIP frames on this PVC. The NetPerformer will discard all RIP frames received. NOTE: If you disable IP RIP on the NetPerformer, but require IP routing to a particular destination (for management under SNMP, for example) you can configure a static IP address using the IP Static menu, described in the LAN Connection and IP Networks fascicle of this document series. Values: DISABLE, V1, V2 BROADCAST, V2 MULTICAST Default: V1 When the V2 BROADCAST or V2 MULTICAST value is selected for the IP RIP parameter, additional IP RIP parameters are also available, as shown in this example: PVC 1> IP RIP (def:V1) ? V2 BROADCAST PVC 1> IP RIP TX/RX (def:DUPLEX) ? PVC 1> IP RIP Authentication (def:NONE) ? PVC 1> IP RIP Password (def:) ? Memotec Inc. 5-11
Page 1 and 2:
ATM Option NetPerformer ® System R
Page 3 and 4:
Contents Chapter 1: Product Overvie
Page 5 and 6:
4. 10 ILMI Channel VCI . . . . . .
Page 7 and 8:
5.8.1 ATM Adaptation Layer . . . .
Page 9 and 10:
Product Overview 1 Memotec Inc. 1-1
Page 11 and 12:
Product Overview and higher capacit
Page 13 and 14:
1.2.2 Error Checking 1.2.3 Cell Tra
Page 15 and 16:
Product Overview • Another diffic
Page 17 and 18:
1.2.7 ATM Addressing Product Overvi
Page 19 and 20:
NOTE: Service categories can be def
Page 21 and 22:
1.3 ATM Support on the NetPerformer
Page 23 and 24:
Product Overview 7. Link to another
Page 25 and 26:
Product Overview The NetPerformer p
Page 27 and 28:
Product Overview page 1-21). Howeve
Page 29 and 30:
Product Overview - Congestion is de
Page 31 and 32:
1.3.5 PPP Over AAL5 Product Overvie
Page 33 and 34:
AAL0 Adaptation Layer Product Overv
Page 35 and 36:
Product Overview On the SDM-9360A,
Page 37 and 38:
SVC Modes Supported Product Overvie
Page 39 and 40:
Configuration 2 Memotec Inc. 2-1
Page 41 and 42:
Configuration When you execute the
Page 43 and 44:
Unit ID> (main prompt) Figure 2-1:
Page 45 and 46:
SE/GLOBAL example: with ATM license
Page 47 and 48:
Configuration Included in this calc
Page 49 and 50:
SE/SLOT example: with data channels
Page 51 and 52:
2.5 Configuring the Digital Link Co
Page 53 and 54:
2.6 Configuring the ATM Channel Con
Page 55 and 56:
2.7 Configuring the ATM PVCs Config
Page 57 and 58: SE/PVC/ ATMPVCR example: on the SDM
Page 59 and 60: 2.7.2 PVC in AAL1 Mode SE/PVC/AAL1
Page 61 and 62: SE/PVC/ RFC1483 example Configurati
Page 63 and 64: 2.7.6 PVC in ATM-MULTIPLEX Mode SE/
Page 65 and 66: 2.8.1 SVC in ATMPVCR Mode SE/SVC/ A
Page 67 and 68: SE/SVC/ ATMPVCR example: ANSWER Typ
Page 69 and 70: 2.8.4 SVC in ATMPPP Mode SE/SVC/ AT
Page 71 and 72: 2.9 Configuration Examples Configur
Page 73 and 74: SE/PVC/#/ ATMPVCR example PVC Confi
Page 75 and 76: Monitoring and Statistics 3 Memotec
Page 77 and 78: Monitoring and Statistics NOTE: Vie
Page 79 and 80: Monitoring and Statistics SVC 1> Nu
Page 81 and 82: SVC Status Console SNMP SVC Status
Page 83 and 84: DSVC/ATM example Monitoring and Sta
Page 85 and 86: 3.3 Status of ATM PVCs DC/PVC examp
Page 87 and 88: DE/PVC example Monitoring and Stati
Page 89 and 90: 3.4 Viewing Reserved Channels DP/GL
Page 91 and 92: 3.5 Status of ATM Channels DC/SLOT
Page 93 and 94: SE/SLOT/CHANNEL Configuration Param
Page 95 and 96: 4.4 Scrambling function 4.5 UNI Ver
Page 97 and 98: 4.8 ATM Signaling Channel VCI SE/SL
Page 99 and 100: SE/PVC Configuration Parameters 5 M
Page 101 and 102: SE/PVC Configuration Parameters Val
Page 103 and 104: 5.3.3 Service category Values: SDM-
Page 105 and 106: 5.3.6 Maximum burst size (MBS) in c
Page 107: SE/PVC Configuration Parameters NOT
Page 111 and 112: 5.3.20 OSPF face on both sides of t
Page 113 and 114: 5.3.24 OSPF Hello interval 5.3.25 O
Page 115 and 116: 5.3.29 IP multicast protocol 5.3.30
Page 117 and 118: 5.3.34 Broadcast group SE/PVC Confi
Page 119 and 120: 5.3.37 Cell Packetization SE/PVC Co
Page 121 and 122: SE/PVC Configuration Parameters of
Page 123 and 124: SE/PVC Configuration Parameters M-l
Page 125 and 126: 5.4.12 TONE ON (ms) 5.4.13 TONE OFF
Page 127 and 128: 5.4.16 Fwd digits SE/PVC Configurat
Page 129 and 130: 5.5 FRF.8 Mode 5.5.1 Port 5.5.2 DLC
Page 131 and 132: SE/PVC Configuration Parameters •
Page 133 and 134: 5.5.8 Frame relay DE bit 5.5.9 Fram
Page 135 and 136: 5.6 RFC1483 Mode 5.6.1 BRG connecti
Page 137 and 138: 5.8.2 Remote PVC number 5.8.3 Class
Page 139 and 140: SE/SVC Configuration Parameters 6 M
Page 141 and 142: 6.3 ATMPVCR Mode 6.3.1 SVC Destinat
Page 143 and 144: 6.3.7 Call Retry Delay 6.3.8 Peak c
Page 145 and 146: Index A AAL service classes 1-4 AAL
Page 147 and 148: IP RIP password 5-12 IP RIP TX/RX 5
Page 149 and 150: ATM Option 5
show all

ATM Option System Reference - Comtech EF Data

Create successful ePaper yourself

Delete template?

Save as template?