ATM Option System Reference - Comtech EF Data

More documents

Recommendations

Info

ATM Option 4.1 Idle cell Determines the format used for idle cells. Select ATM-UNI for the User-to-Network Interface format. Select ITU-T for the ITU-T format. Refer to “User to Network Interface (UNI)” on page 1-7. 4.2 Idle cell payload Console SNMP Text-based Config Idle cell ifwanIdleCell [ifwan#] IdleCell Values: ATM-UNI, ITU-T Default: ITU-T Console SNMP Text-based Config Idle cell payload ifwanIdleCellPayload [ifwan#] IdleCellPayload Determines the payload content for idle cells on the ATM channel. Values: 00000000 - FFFFFFFF Default: 6A6A6A6A 4.3 HEC coset function Console SNMP Text-based Config HEC coset function ifwanHECCosetFunction [ifwan#] HECCosetFunction Enables or disables the Header Error Check (HEC) coset function, which is required for some ATM switches. • When you select ENABLE (the default value), the NetPerformer applies the HEC coset to all cells that are transmitted or received across this channel • When you select DISABLE, the HEC coset rules are not applied. Values: DISABLE, ENABLE Default: ENABLE 4-2 Memotec Inc.
4.4 Scrambling function 4.5 UNI Version SE/SLOT/CHANNEL Configuration Parameters Console SNMP Text-based Config Scrambling function ifwanScramblingFunction [ifwan#] ScramblingFunction Enables or disables cell scrambling, which permits randomizing the cell payload. Cell scrambling can be used to avoid a continuous stream of invariable bit patterns, which can improve the efficiency of cell delineation. • When you select ENABLE the NetPerformer applies cell scrambling before transmission, and descrambling on the received traffic stream. Cell scrambling must be enabled on both sides of the connection. • When you select DISABLE (the default value), cell scrambling is not applied. Values: DISABLE, ENABLE Default: DISABLE Console SNMP Text-based Config UNI Version ifwanAtmUniVersion [ifwan#] AtmUniVersion Select the value that matches the UNI version used by the ATM switch: • NONE: UNI is not used. The ILMI and signaling VCs are not established. • 4.0: UNI 4.0 • 3.1: UNI 3.1 • 3.0: UNI 3.0 NOTE: Auto configuration of this parameter is not supported. Refer to “User to Network Interface (UNI)” on page 1-7 for further information. Values: NONE, 4.0, 3.1, 3.0 Default: 4.0 Memotec Inc. 4-3
Page 1 and 2:
ATM Option NetPerformer ® System R
Page 3 and 4:
Contents Chapter 1: Product Overvie
Page 5 and 6:
4. 10 ILMI Channel VCI . . . . . .
Page 7 and 8:
5.8.1 ATM Adaptation Layer . . . .
Page 9 and 10:
Product Overview 1 Memotec Inc. 1-1
Page 11 and 12:
Product Overview and higher capacit
Page 13 and 14:
1.2.2 Error Checking 1.2.3 Cell Tra
Page 15 and 16:
Product Overview • Another diffic
Page 17 and 18:
1.2.7 ATM Addressing Product Overvi
Page 19 and 20:
NOTE: Service categories can be def
Page 21 and 22:
1.3 ATM Support on the NetPerformer
Page 23 and 24:
Product Overview 7. Link to another
Page 25 and 26:
Product Overview The NetPerformer p
Page 27 and 28:
Product Overview page 1-21). Howeve
Page 29 and 30:
Product Overview - Congestion is de
Page 31 and 32:
1.3.5 PPP Over AAL5 Product Overvie
Page 33 and 34:
AAL0 Adaptation Layer Product Overv
Page 35 and 36:
Product Overview On the SDM-9360A,
Page 37 and 38:
SVC Modes Supported Product Overvie
Page 39 and 40:
Configuration 2 Memotec Inc. 2-1
Page 41 and 42:
Configuration When you execute the
Page 43 and 44: Unit ID> (main prompt) Figure 2-1:
Page 45 and 46: SE/GLOBAL example: with ATM license
Page 47 and 48: Configuration Included in this calc
Page 49 and 50: SE/SLOT example: with data channels
Page 51 and 52: 2.5 Configuring the Digital Link Co
Page 53 and 54: 2.6 Configuring the ATM Channel Con
Page 55 and 56: 2.7 Configuring the ATM PVCs Config
Page 57 and 58: SE/PVC/ ATMPVCR example: on the SDM
Page 59 and 60: 2.7.2 PVC in AAL1 Mode SE/PVC/AAL1
Page 61 and 62: SE/PVC/ RFC1483 example Configurati
Page 63 and 64: 2.7.6 PVC in ATM-MULTIPLEX Mode SE/
Page 65 and 66: 2.8.1 SVC in ATMPVCR Mode SE/SVC/ A
Page 67 and 68: SE/SVC/ ATMPVCR example: ANSWER Typ
Page 69 and 70: 2.8.4 SVC in ATMPPP Mode SE/SVC/ AT
Page 71 and 72: 2.9 Configuration Examples Configur
Page 73 and 74: SE/PVC/#/ ATMPVCR example PVC Confi
Page 75 and 76: Monitoring and Statistics 3 Memotec
Page 77 and 78: Monitoring and Statistics NOTE: Vie
Page 79 and 80: Monitoring and Statistics SVC 1> Nu
Page 81 and 82: SVC Status Console SNMP SVC Status
Page 83 and 84: DSVC/ATM example Monitoring and Sta
Page 85 and 86: 3.3 Status of ATM PVCs DC/PVC examp
Page 87 and 88: DE/PVC example Monitoring and Stati
Page 89 and 90: 3.4 Viewing Reserved Channels DP/GL
Page 91 and 92: 3.5 Status of ATM Channels DC/SLOT
Page 93: SE/SLOT/CHANNEL Configuration Param
Page 97 and 98: 4.8 ATM Signaling Channel VCI SE/SL
Page 99 and 100: SE/PVC Configuration Parameters 5 M
Page 101 and 102: SE/PVC Configuration Parameters Val
Page 103 and 104: 5.3.3 Service category Values: SDM-
Page 105 and 106: 5.3.6 Maximum burst size (MBS) in c
Page 107 and 108: SE/PVC Configuration Parameters NOT
Page 109 and 110: 5.3.16 IP RIP SE/PVC Configuration
Page 111 and 112: 5.3.20 OSPF face on both sides of t
Page 113 and 114: 5.3.24 OSPF Hello interval 5.3.25 O
Page 115 and 116: 5.3.29 IP multicast protocol 5.3.30
Page 117 and 118: 5.3.34 Broadcast group SE/PVC Confi
Page 119 and 120: 5.3.37 Cell Packetization SE/PVC Co
Page 121 and 122: SE/PVC Configuration Parameters of
Page 123 and 124: SE/PVC Configuration Parameters M-l
Page 125 and 126: 5.4.12 TONE ON (ms) 5.4.13 TONE OFF
Page 127 and 128: 5.4.16 Fwd digits SE/PVC Configurat
Page 129 and 130: 5.5 FRF.8 Mode 5.5.1 Port 5.5.2 DLC
Page 131 and 132: SE/PVC Configuration Parameters •
Page 133 and 134: 5.5.8 Frame relay DE bit 5.5.9 Fram
Page 135 and 136: 5.6 RFC1483 Mode 5.6.1 BRG connecti
Page 137 and 138: 5.8.2 Remote PVC number 5.8.3 Class
Page 139 and 140: SE/SVC Configuration Parameters 6 M
Page 141 and 142: 6.3 ATMPVCR Mode 6.3.1 SVC Destinat
Page 143 and 144: 6.3.7 Call Retry Delay 6.3.8 Peak c
Page 145 and 146:
Index A AAL service classes 1-4 AAL
Page 147 and 148:
IP RIP password 5-12 IP RIP TX/RX 5
Page 149 and 150:
ATM Option 5
show all

ATM Option System Reference - Comtech EF Data

Create successful ePaper yourself

Delete template?

Save as template?