ATM Option System Reference - Comtech EF Data

More documents

Recommendations

Info

ATM Option 2.3 Configuration Overview To adapt the NetPerformer for access to network services via ATM, follow these configuration steps: • Configure the global parameters that affect the allocation of memory for data channels and ATM AAL5 VCs, using the SETUP/GLOBAL command. Refer to “Configuring the Global Parameters” on page 2-6. These GLOBAL parameters are not required on the SDM-9230, which does not have the memory constraints that the SDM-9360, SDM-9380 and SDM-9585 have in supporting ATM. • Set up the ATM interface on the digital LINK with the SETUP/SLOT/LINK command, selecting the slot that contains the ATM access interface: a T1 or E1 interface card. Refer to “Configuring the Digital Link” on page 2-13. • Set up the ATM channel with the SETUP/SLOT/CHANNEL command. Refer to “Configuring the ATM Channel” on page 2-15. • Set up the LAN port with the SETUP/PORT command. The LAN port is configured in the same way as for non-ATM applications. For further information, refer to the LAN Connection and IP Networks fascicle of this document series. When the ATM licensed software option is activated on an SDM-9230, the second LAN port (ETH2) is not available and does not appear in the choice of ports for any console command. Only the first LAN port (ETH1) is operative. • Set up the Frame Relay port that connects to the user equipment with the SETUP/ PORT or SETUP/SLOT command. The FR-NET port is configured in the same way as for non-ATM applications. Refer to the NetPerformer User Guide and NetPerformer System Reference Manual for further information. • Set up all required ATM PVCs with the SETUP/PVC command. For details, refer to “Configuring the ATM PVCs” on page 2-17. • Set up all required ATM SVCs with the SETUP/SVC command. Refer to “Configuring the ATM SVCs” on page 2-26 for details. • Set up all required Voice Mapping Table entries using the SETUP/MAP command. Refer to the NetPerformer User Guide and NetPerformer System Reference Manual for information on configuring the MAP entries. 2-4 Memotec Inc.
Unit ID> (main prompt) Figure 2-1: SETUP Command Paths in the CLI Tree for ATM Configuration Configuration Global (GL) MAP (MA) Port (PO) PVC (PV) Slot (SL) SVC (SV) ETH # Setup (SE) FR-NET Memotec Inc. 2-5 Link NONE Channel ATM
Page 1 and 2: ATM Option NetPerformer ® System R
Page 3 and 4: Contents Chapter 1: Product Overvie
Page 5 and 6: 4. 10 ILMI Channel VCI . . . . . .
Page 7 and 8: 5.8.1 ATM Adaptation Layer . . . .
Page 9 and 10: Product Overview 1 Memotec Inc. 1-1
Page 11 and 12: Product Overview and higher capacit
Page 13 and 14: 1.2.2 Error Checking 1.2.3 Cell Tra
Page 15 and 16: Product Overview • Another diffic
Page 17 and 18: 1.2.7 ATM Addressing Product Overvi
Page 19 and 20: NOTE: Service categories can be def
Page 21 and 22: 1.3 ATM Support on the NetPerformer
Page 23 and 24: Product Overview 7. Link to another
Page 25 and 26: Product Overview The NetPerformer p
Page 27 and 28: Product Overview page 1-21). Howeve
Page 29 and 30: Product Overview - Congestion is de
Page 31 and 32: 1.3.5 PPP Over AAL5 Product Overvie
Page 33 and 34: AAL0 Adaptation Layer Product Overv
Page 35 and 36: Product Overview On the SDM-9360A,
Page 37 and 38: SVC Modes Supported Product Overvie
Page 39 and 40: Configuration 2 Memotec Inc. 2-1
Page 41: Configuration When you execute the
Page 45 and 46: SE/GLOBAL example: with ATM license
Page 47 and 48: Configuration Included in this calc
Page 49 and 50: SE/SLOT example: with data channels
Page 51 and 52: 2.5 Configuring the Digital Link Co
Page 53 and 54: 2.6 Configuring the ATM Channel Con
Page 55 and 56: 2.7 Configuring the ATM PVCs Config
Page 57 and 58: SE/PVC/ ATMPVCR example: on the SDM
Page 59 and 60: 2.7.2 PVC in AAL1 Mode SE/PVC/AAL1
Page 61 and 62: SE/PVC/ RFC1483 example Configurati
Page 63 and 64: 2.7.6 PVC in ATM-MULTIPLEX Mode SE/
Page 65 and 66: 2.8.1 SVC in ATMPVCR Mode SE/SVC/ A
Page 67 and 68: SE/SVC/ ATMPVCR example: ANSWER Typ
Page 69 and 70: 2.8.4 SVC in ATMPPP Mode SE/SVC/ AT
Page 71 and 72: 2.9 Configuration Examples Configur
Page 73 and 74: SE/PVC/#/ ATMPVCR example PVC Confi
Page 75 and 76: Monitoring and Statistics 3 Memotec
Page 77 and 78: Monitoring and Statistics NOTE: Vie
Page 79 and 80: Monitoring and Statistics SVC 1> Nu
Page 81 and 82: SVC Status Console SNMP SVC Status
Page 83 and 84: DSVC/ATM example Monitoring and Sta
Page 85 and 86: 3.3 Status of ATM PVCs DC/PVC examp
Page 87 and 88: DE/PVC example Monitoring and Stati
Page 89 and 90: 3.4 Viewing Reserved Channels DP/GL
Page 91 and 92: 3.5 Status of ATM Channels DC/SLOT
Page 93 and 94:
SE/SLOT/CHANNEL Configuration Param
Page 95 and 96:
4.4 Scrambling function 4.5 UNI Ver
Page 97 and 98:
4.8 ATM Signaling Channel VCI SE/SL
Page 99 and 100:
SE/PVC Configuration Parameters 5 M
Page 101 and 102:
SE/PVC Configuration Parameters Val
Page 103 and 104:
5.3.3 Service category Values: SDM-
Page 105 and 106:
5.3.6 Maximum burst size (MBS) in c
Page 107 and 108:
SE/PVC Configuration Parameters NOT
Page 109 and 110:
5.3.16 IP RIP SE/PVC Configuration
Page 111 and 112:
5.3.20 OSPF face on both sides of t
Page 113 and 114:
5.3.24 OSPF Hello interval 5.3.25 O
Page 115 and 116:
5.3.29 IP multicast protocol 5.3.30
Page 117 and 118:
5.3.34 Broadcast group SE/PVC Confi
Page 119 and 120:
5.3.37 Cell Packetization SE/PVC Co
Page 121 and 122:
SE/PVC Configuration Parameters of
Page 123 and 124:
SE/PVC Configuration Parameters M-l
Page 125 and 126:
5.4.12 TONE ON (ms) 5.4.13 TONE OFF
Page 127 and 128:
5.4.16 Fwd digits SE/PVC Configurat
Page 129 and 130:
5.5 FRF.8 Mode 5.5.1 Port 5.5.2 DLC
Page 131 and 132:
SE/PVC Configuration Parameters •
Page 133 and 134:
5.5.8 Frame relay DE bit 5.5.9 Fram
Page 135 and 136:
5.6 RFC1483 Mode 5.6.1 BRG connecti
Page 137 and 138:
5.8.2 Remote PVC number 5.8.3 Class
Page 139 and 140:
SE/SVC Configuration Parameters 6 M
Page 141 and 142:
6.3 ATMPVCR Mode 6.3.1 SVC Destinat
Page 143 and 144:
6.3.7 Call Retry Delay 6.3.8 Peak c
Page 145 and 146:
Index A AAL service classes 1-4 AAL
Page 147 and 148:
IP RIP password 5-12 IP RIP TX/RX 5
Page 149 and 150:
ATM Option 5
show all

ATM Option System Reference - Comtech EF Data

Create successful ePaper yourself

Delete template?

Save as template?