Fravol Smart Series Edgebander Manual & Parts List

More documents

Recommendations

Info

USER’S MANUAL AND MAINTENANCE Set to position (0) the main switch (pos.A fig.10), remove the 4 screws (pos.B pict.10) on the box and open it. With reference to pict.9 and 10, thread the power supply cable cable (C) made up of 3 3 phase wires + + one one Neutral Neutral cable and one ground wire: (colour: yellow-green) of proper dimensions through the cable locker until the terminal board. Connect the phase wires to the proper sockets labelled with R-S-T+N and the ground wires wires (colour: yellow-green) yellow-green) to to the the terminal labelled with the symbol. After the connection to the electrical system, make sure that the engine engine rotation is correct. To do do that, enable the machine to work for few seconds seconds and see if the the rotation of of the belt and of the other tools is correct. If not, invert the the two phases at the the entrance of the the main switch of the machine. The HF (High Frequency) engines supplied by the inverter may turn in in the opposite sense because of the effect of the auto-reverse on the rotation rotation of the belt . In this case (correct rotation of the belt but wrong wrong rotations rotations of the HF HF engines ) check check each engine engine of the end-trimming unit, of the scrape unit etc 02.5 CONNECTION OF THE DUST SUCTION SYSTEM Pic. 11 A suction outlet has been installed (Ø 80 for the roughing unit and Ø 50 for the scraping unit) to remove the shavings shavings from the roughing roughing unit and scraping unit work areas areas (where required). The outlet is connected to the respective respective suction collectors by a flexible pipe Ø 120 (Fig. 12). The air aspirated will will have to reach reach at least 900 m3/h with a flux speed of 25m/s. 25m/s. Install Install a guillotine valve on the the suction pipes pipes in order order to insulate the machine from the the suction circuit. Check the efficiency of the system because, if of poor quality, it may cause damages to the machine and the operator’s health. Rev 1-03/07 19
USER’S MANUAL AND MAINTENANCE Pic. 12 2.6 CONNECTION OF THE PNEUMATIC SYSTEM Please look up the pneumatic scheme enclosed. The distribution pressure of the compressed air supply system must not be lower than 6 bar. The minimum inside inside diameter of the inner inner sections of the hoses hoses must be 8mm to make up for the inevitable pressure losses along along the the distribution line. line. Make sure that there there is no condensation, solid impurities or scales in the air distribution distribution system. Connect the machine through a hose with inner diameter of 6 to the opening (pos.C pict. 13) placed out of the side panel. Pic. 13 Rev 1-03/07 20
Page 1 and 2: INDEX CHAPTER 01 I INTRODUCTION 1.1
Page 3 and 4: ACCESSORY 21 ROUNDING UNIT USER’S
Page 5 and 6: USER’S MANUAL AND MAINTENANCE Rev
Page 7 and 8: 13) ACCESSORY 18 USER’S MANUAL AN
Page 9 and 10: 1.6 OVERALL DIMENSIONS 1.7 TECHNICA
Page 11 and 12: USER’S MANUAL AND MAINTENANCE •
Page 13 and 14: USER’S MANUAL AND MAINTENANCE SAF
Page 15 and 16: APPAREL: USER’S MANUAL AND MAINTE
Page 17 and 18: SAFE MAINTENANCE: USER’S MANUAL A
Page 19 and 20: DANGER: USER’S MANUAL AND MAINTEN
Page 21: 02.4 CONNECTION OF THE ELECTRIC SYS
Page 25 and 26: USER’S MANUAL AND MAINTENANCE Mak
Page 27 and 28: LED DESCRIPTION USER’S MANUAL AND
Page 29 and 30: 03 USAGE 03.1 USAGE TIPS USER’S M
Page 31 and 32: 03.3 FUNCTIONNING (AUTOMATIC) FOR S
Page 33 and 34: ATTENTION: USER’S MANUAL AND MAIN
Page 35 and 36: 6 36 64 7 34 23+24 8 36 6 9 34 7 10
Page 37 and 38: 4.3 LUBRICATOR TABLE USER’S MANUA
Page 39 and 40: USER’S MANUAL AND MAINTENANCE Sel
Page 41 and 42: USER’S MANUAL AND MAINTENANCE You
Page 43 and 44: strips will automatically find thei
Page 45 and 46: A03. 07 HELPFUL TIPS USER’S MANUA
Page 47 and 48: A06. 02 PNEUMATIC ADJUSTMENTS USER
Page 49 and 50: USER’S MANUAL AND MAINTENANCE Pne
Page 51 and 52: A07. 02 ADJUSTMENTS Reference to pi
Page 53 and 54: USER’S MANUAL AND MAINTENANCE A08
Page 55 and 56: USER’S MANUAL AND MAINTENANCE The
Page 57 and 58: USER’S MANUAL AND MAINTENANCE Cha
Page 59 and 60: USER’S MANUAL AND MAINTENANCE To
Page 65 and 66: USER’S MANUAL AND MAINTENANCE The
Page 67 and 68: USER’S MANUAL AND MAINTENANCE If
Page 69 and 70: A10 SCRAPER UNIT ACCESSORY N. 10 A1
Page 71 and 72: USER’S MANUAL AND MAINTENANCE 1 L
Page 73 and 74:
A11. 02 ADJUSTMENT USER’S MANUAL
Page 75 and 76:
A13 BLOWING UNIT ACCESSORY N. 13 US
Page 77 and 78:
A21 ROUNDING UNIT ACCESSORY N° 19
Page 79 and 80:
USER’S MANUAL AND MAINTENANCE the
Page 81 and 82:
USER’S MANUAL AND MAINTENANCE THE
Page 83 and 84:
USER’S MANUAL AND MAINTENANCE A21
Page 85 and 86:
USER’S MANUAL AND MAINTENANCE Sol
Page 87 and 88:
USER’S MANUAL AND MAINTENANCE Def
Page 89 and 90:
USER’S MANUAL AND MAINTENANCE A23
Page 91 and 92:
USER’S MANUAL AND MAINTENANCE Do
Page 93 and 94:
A16. 02 LUBRICATOR ADJUSTMENTS USER
Page 95 and 96:
CAUTION: USER’S MANUAL AND MAINTE
Page 98 and 99:
Questo catalogo riporta informazion
Page 100 and 101:
Catalogo ricambi Spare parts catalo
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204:
show all

Fravol Smart Series Edgebander Manual & Parts List

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?