Fravol Smart Series Edgebander Manual & Parts List

More documents

Recommendations

Info

USER’S MANUAL AND MAINTENANCE A21. 06 ADJUSTMENTS AFTER THE SHARPENING OF THE UNIT With reference to picture 9. After the tool tool has been sharpened, sharpened, its diameter will be be lower, lower, therefore you'll need to adjust the radial copier (CR) opposite to it. Before carrying out the adjustments we suggest you to write down the outside diameter before the sharpening by using a 1/20 vernier callipers and reproduce the same measure after the sharpening. The difference between the two will be about equal to the shift of the cylindrical copier. 1 loosen the 4 blocking screws (E) of the copier slide; 2 adjust the copier by turning screw (A) considering that one turn of the screw (A) corresponds to a 1 mm shift. 3 fasten the 4 blocking screws (E). fig. 9 A21. 07 ISSUES AND SOLUTIONS The position of the radial copier (RC) is adjusted during testing. However, some adjustments could be needed when the the tool is worn and cuts less less or after after its sharpening. The The adjustments to be made depend on the type of rounding work work of the the panel. There can be different cases: The rounding of the heads of the panel is not crimped to the lateral edge previously glued or to the rolled surface of the panel. 1ë case: the radius is incomplete as to the rolled part (pict. 10). Rev 0-12/05 A21-8
USER’S MANUAL AND MAINTENANCE Solution: loosen the 4 screws (E) (pict.9) and lower the radial copier (CR) by turning the adjustment screw (A) (pict.9). fig. 10 2°case: the radius is incomplete as to the edge just just glued (pict.11) Solution: loosen screw (V) (pict.9) and push the cutter engine forward towards the panel panel by turning the adjustment screw (B) (pict.9). fig. 11 Rev 0-12/05 A21-9
Page 1 and 2:
INDEX CHAPTER 01 I INTRODUCTION 1.1
Page 3 and 4:
ACCESSORY 21 ROUNDING UNIT USER’S
Page 5 and 6:
USER’S MANUAL AND MAINTENANCE Rev
Page 7 and 8:
13) ACCESSORY 18 USER’S MANUAL AN
Page 9 and 10:
1.6 OVERALL DIMENSIONS 1.7 TECHNICA
Page 11 and 12:
USER’S MANUAL AND MAINTENANCE •
Page 13 and 14:
USER’S MANUAL AND MAINTENANCE SAF
Page 15 and 16:
APPAREL: USER’S MANUAL AND MAINTE
Page 17 and 18:
SAFE MAINTENANCE: USER’S MANUAL A
Page 19 and 20:
DANGER: USER’S MANUAL AND MAINTEN
Page 21 and 22:
02.4 CONNECTION OF THE ELECTRIC SYS
Page 23 and 24:
USER’S MANUAL AND MAINTENANCE Pic
Page 25 and 26:
USER’S MANUAL AND MAINTENANCE Mak
Page 27 and 28:
LED DESCRIPTION USER’S MANUAL AND
Page 29 and 30:
03 USAGE 03.1 USAGE TIPS USER’S M
Page 31 and 32:
03.3 FUNCTIONNING (AUTOMATIC) FOR S
Page 33 and 34: ATTENTION: USER’S MANUAL AND MAIN
Page 35 and 36: 6 36 64 7 34 23+24 8 36 6 9 34 7 10
Page 37 and 38: 4.3 LUBRICATOR TABLE USER’S MANUA
Page 39 and 40: USER’S MANUAL AND MAINTENANCE Sel
Page 41 and 42: USER’S MANUAL AND MAINTENANCE You
Page 43 and 44: strips will automatically find thei
Page 45 and 46: A03. 07 HELPFUL TIPS USER’S MANUA
Page 47 and 48: A06. 02 PNEUMATIC ADJUSTMENTS USER
Page 49 and 50: USER’S MANUAL AND MAINTENANCE Pne
Page 51 and 52: A07. 02 ADJUSTMENTS Reference to pi
Page 53 and 54: USER’S MANUAL AND MAINTENANCE A08
Page 55 and 56: USER’S MANUAL AND MAINTENANCE The
Page 57 and 58: USER’S MANUAL AND MAINTENANCE Cha
Page 59 and 60: USER’S MANUAL AND MAINTENANCE To
Page 65 and 66: USER’S MANUAL AND MAINTENANCE The
Page 67 and 68: USER’S MANUAL AND MAINTENANCE If
Page 69 and 70: A10 SCRAPER UNIT ACCESSORY N. 10 A1
Page 71 and 72: USER’S MANUAL AND MAINTENANCE 1 L
Page 73 and 74: A11. 02 ADJUSTMENT USER’S MANUAL
Page 75 and 76: A13 BLOWING UNIT ACCESSORY N. 13 US
Page 77 and 78: A21 ROUNDING UNIT ACCESSORY N° 19
Page 79 and 80: USER’S MANUAL AND MAINTENANCE the
Page 81 and 82: USER’S MANUAL AND MAINTENANCE THE
Page 83: USER’S MANUAL AND MAINTENANCE A21
Page 87 and 88: USER’S MANUAL AND MAINTENANCE Def
Page 91 and 92: USER’S MANUAL AND MAINTENANCE Do
Page 93 and 94: A16. 02 LUBRICATOR ADJUSTMENTS USER
Page 95 and 96: CAUTION: USER’S MANUAL AND MAINTE
Page 98 and 99: Questo catalogo riporta informazion
Page 100 and 101: Catalogo ricambi Spare parts catalo
Page 134 and 135:
Catalogo ricambi Spare parts catalo
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204:
show all

Fravol Smart Series Edgebander Manual & Parts List

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?