Start-Up, Operation, and Maintenance Instructions

More documents

Recommendations

Info

AUX — Auxiliary BR CB — — Bridge Rectifier Circuit Breaker COND — Condenser CPU — Central Processing Unit CVC/ ICVC — Chiller Visual Controller CT — Current Transformer EVAP — Evaporator FU — Fuse GND — Ground LEGEND L — Main Supply Power LL — Control Power Supply M — Contactor O/L — Overload Reset PFCC — Power Factor Correction Capacitor RLA — Rated Load Amps SCR — Silicone Controller Rectifier ST — Shunt Trip TB — Terminal Block NOTES: 1 LED status with power applied and prior to run command. 2 3 4 5 6 "ON" "OFF" Fig. 53 — Benshaw, Inc. Solid-State Unit Mounted Starter Wiring Schematic (Low Voltage) (cont) 112 Wire Node Symbol may have terminal block Benshaw supplied terminal block Terminal Strip Power Connection Transformer T1 primary fuses FU1/FU2 value dependent on system voltage and model, per Chart 1. Transformer connections per transformer nameplate connection diagram. MOVs are used on power stack assemblies for system voltages of 200 through 460 vac (as shown). Resistor/capacitor networks (DVDTs) are used on power stack assemblies in place of MOVs for a system voltage of 575 vac (not shown). K3 relay shown in deenergized state. K3 contact will close when power is supplied. K3 contact will open on stop command or system fault. CT1-CT3 are sized per Chart 2. Optional. PC Board Terminals Twisted Pair Twisted Shielded Pair Shield Wire Field Wiring
LEGEND AUX — Auxiliary C — Contactor CB — Circuit Breaker COMM — Communication COND — Condenser CPT — Control Power Transformer CR — Control Relay CT — Current Transformer DS — Disconnect Switch EVAP — Evaporator FU — Fuse G — Ground GFCT — Ground Fault Current Transformer HPR — High Pressure Relay ISM — Integrated Starter Module L — Main Power Supply LL — Control Power Supply LVG — Leaving M — Contactor MTR — Motor PRESS — Pressure PT — Power Transformer ST — Shunt Trip STAT — Status TB — Terminal Block TRANS — Transition VFD — Variable Frequency Drive VL — Wire Label Starter Vendor Power Wiring Starter Vendor Control Wiring Field Installed Power Wiring (supplied by others) Field Installed Control Wiring (supplied by others) Option — Starter Vendor Wiring Twisted Pair Wiring by Starter Vendor Customer Terminal Connection 113 Fig. 54 — Typical Across-the-Line Starter Wiring Schematic (Medium Voltage)
Page 1 and 2:
Start-Up, Operation, and Maintenanc
Page 3 and 4:
CONTENTS (cont) Page Page Chiller D
Page 5 and 6:
Factory-installed additional compon
Page 7 and 8:
Factory-Mounted Starter or Variable
Page 9 and 10:
MOTOR COOLING LINE TXV BULB PRESSUR
Page 11 and 12:
OPTIONAL METER PACKAGE INTEGRATED S
Page 13 and 14:
The PIC II can interface with the C
Page 15 and 16:
CVC/ICVC Operation and Menus (Fig.
Page 17 and 18:
Start Chiller In CCN Control Start
Page 19 and 20:
SERVICE MENU CONTINUED FROM PREVIOU
Page 21 and 22:
7. Press ENTER to register the valu
Page 23 and 24:
Table 2 — CVC/ICVC Display Data (
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
PIC II System Functions NOTE: Words
Page 35 and 36:
Shunt Trip (Option) — The functio
Page 37 and 38:
OVERRIDE CAPACITY CONTROL HIGH COND
Page 39 and 40:
(see wiring diagrams or certified d
Page 41 and 42:
NOTE: The lead/lag function can be
Page 43 and 44:
Ice Build Control — The ice build
Page 45 and 46:
Service Operation — An overview o
Page 47 and 48:
Shutdown Sequence — Chiller shutd
Page 49 and 50:
49 Fig. 28 — 19XR Leak Test Proce
Page 51 and 52:
Fig. 29 — Typical Optional Pumpou
Page 53 and 54:
Chiller Dehydration — Dehydration
Page 55 and 56:
MECHANICAL STARTER 1. Check all fie
Page 57 and 58:
CHANGE THE BENSHAW INC., RediStart
Page 59 and 60:
VFD Cooling System Leak Inspection
Page 61 and 62: Protecting the VFD Configuration 1.
Page 63 and 64: Check Optional Pumpout System Contr
Page 65 and 66: Dry Run to Test Start-Up Sequence F
Page 67 and 68: Leave the oil charge in the chiller
Page 69 and 70: LEGEND C — Contactor FU — Fuse,
Page 71 and 72: 2. Evacuate the refrigerant gas fro
Page 73 and 74: SCHEDULED MAINTENANCE Establish a r
Page 75 and 76: Water Treatment — Untreated or im
Page 77 and 78: TRANSDUCER REPLACEMENT — Since th
Page 79 and 80: Table 11 — CVC/ICVC Primary and S
Page 81 and 82: I. CHILLER PROTECT LIMIT FAULTS STA
Page 83 and 84: I. CHILLER PROTECT LIMIT FAULTS (co
Page 85 and 86: TEMPERATURE (F) PIC II VOLTAGE DROP
Page 87 and 88: Control Modules Turn controller pow
Page 89 and 90: ANALOG OUT J8 INTERGRATED STARTER M
Page 91 and 92: NOTES: 1. Cooler data: based on a c
Page 93 and 94: Table 14 — 19XR Additional Data f
Page 95 and 96: HEAT EXCHANGER COOLER/ CONDENSER HE
Page 97 and 98: Table 18 — Optional Pumpout Syste
Page 99 and 100: ITEM A B C D E F VIEW B — HIGH SP
Page 101 and 102: 101 Fig. 45 — Allen-Bradley Wye-D
Page 103 and 104: 103 LEGEND (cont) ISM — Integrate
Page 105 and 106: 105 LEGEND (cont) ISM — Integrate
Page 107 and 108: 107 LEGEND Denotes Component Termin
Page 109 and 110: AUX — Auxiliary C — Contactor C
Page 111: Fig. 53 — Benshaw, Inc. Solid-Sta
Page 115 and 116: 1A LEGEND AUX — Auxiliary C — C
Page 117 and 118: 117 Fig. 57 — Typical Variable Fr
Page 123 and 124: Abbreviations and Explanations, 4 A
Page 125 and 126: MACHINE INFORMATION: DESIGN CONDITI
Page 127 and 128: 19XR, XRV PIC II SETPOINT TABLE CON
Page 129 and 130: CUT ALONG DOTTED LINE CUT ALONG DOT
Page 140: Copyright 2001 Carrier Corporation
show all

Start-Up, Operation, and Maintenance Instructions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?