Technical Manual - Tunstall GmbH

More documents

Recommendations

Info

12.5 System control 19 0700 10 Group Electronic (GE) 19 0700 00 Management Interface CONCENTO PLUS - Technical Manual, 11/12 (Rev. 3.0), 00 8814 14 Technical Manual Page 122 12. Product leaflets
Tunstall GmbH, Orkotten 66, 48291 Telgte, www.tunstall.de Group electronic (GE), order no. 19 0700 10 The group electronic (abbreviation: GE) is for controlling a ward bus of a nurse call system, type CONCENTO PLUS (max. 40 ward bus users). All GE units are connected to each other via the group bus. Additionally one management interface and one fire alarm interface can be connected to the group bus (max. 40 group bus users). It is possible to install the GE in an existing nurse call system of the type ”Concento” if the ConLog II or ConLog PLUS software is used in the system. Dimensions incl. mounting plate (HxWxD): 190 x 102 x 50 mm GE weight: approx. 295 g, mounting plate weight: 60 g Standby current consumption: 60 mA at 24 V DC The mounting kit (order no. 19 0700 90), i.e. the mounting plate with three connectors, must be ordered separately. Note! Complete installation of the system is described in the Technical Manual. Caution! Electrostatic sensitive components The printed circuit boards in the GE contain electrostatic sensitive components. Therefore, avoid touching them. Mounting in an existing Concento nurse call system If you install the GE in a nurse call system with speech transmis‐ sion and if terminals, GEs or interfaces are installed there, the order no. of which does not begin with ”19 07”, you must set the type ”Concento” on the GE instead of ”CONCENTOPLUS ” (factory setting). Proceed as follows to set ”Concento” in an existing Concento nurse call system (see Fig. B): 1. Lever off the cover 2 on the side of the GE 1 with a screwdriver and then remove it. 2. Slide the slide switch upwards into the ”Concento” position. 3. Replace the cover 2 and press it on until it clicks into place. Mounting Wall mounting preferably in the electrical sub-distribution unit. 1. Strip the connecting cable to a suitable length. Remove the cable shield and the ground wire up to the cable sheath. 2. Connect the wires according to Fig. F to the three connectors included with the mounting kit. 3. Set the two DIP switches beside the connection field 8 on the rear of the GE as per Fig. E. 4. Push the three connected connectors through the opening of the mounting plate 5. 5. Securely screw the mounting plate 5 to the back box 6 with the four back box screws 4. 6. Plug the three wired connectors onto the connection field 8 on the back of the GE, see Fig. A. 7. Attach the GE 1 to the mounting plate 5 so that the four protruding screws 3 are inserted into the ”keyholes” of the mounting plate 5. 8. Slide down the GE 1 until it clicks into place 00 8814 01, 10/12 (Rev. 3.0) 1 Technical Manual Page 123 1 Front view 2 3 3 3 3 1 Rear view 1 Group electronic (abbreviation: GE) 2 Cover on the side of GE 3 Four protruding screws 4* Four back box screws 5* Mounting plate 6* Back box 7* Mounting plate latch 8 Connection field * Not included with product delivery. 1 1 2 2 3 3 3 3 4 4 7 8 Slide switch Concento 1 CONCENTO PLUS (Factory setting) 4 4 5 6
Page 1 and 2:
CONCENTO PLUS Technical Manual COMM
Page 3 and 4:
CONCENTO PLUS - Technical Manual, 1
Page 5 and 6:
Page 7 and 8:
1.5 General safety regulations CONC
Page 9 and 10:
2. Prior knowledge required 2.1 Sys
Page 11 and 12:
Page 13 and 14:
2.4 ConLog PLUS Management Software
Page 15 and 16:
2.5.2 Group speech Group bus CONCEN
Page 17 and 18:
Page 19 and 20:
Per room Per bed In WC room Termina
Page 21 and 22:
Per room Per bed In WC room Display
Page 23 and 24:
3.3 Staff room c+k Per room CONCENT
Page 25 and 26:
3.4.2 Function room without speech
Page 27 and 28:
3.5.2 Ward bathroom without speech
Page 29 and 30:
Per room Display module or Call/pre
Page 31 and 32:
Per room Terminal SD6 P or Terminal
Page 33 and 34:
Per room Display module or Call/pre
Page 35 and 36:
Per apartment Per bed Terminal S4 B
Page 37 and 38:
4. Accessories required Accessories
Page 39 and 40:
5. Installation examples See below
Page 41 and 42:
5.2 Nurse call system with speech:
Page 43 and 44:
5.4 Assisted living g (equipotentia
Page 45 and 46:
5.5.2 1‐bed room with WC Ward bus
Page 47 and 48:
5.5.4 1-bed room with WC: Wiring in
Page 49 and 50:
6. Installation sequence Work step
Page 51 and 52:
7. Defining mounting positions 7.1
Page 53 and 54:
7. Defining mounting positions 7.3
Page 55 and 56:
7.3.3 Switches ÀÀ ÀÀÀÀÀ ÀÀ
Page 57 and 58:
Page 59 and 60:
8.3 Power supply cable (code: k) CO
Page 61 and 62:
8.3.1 Earthing the nurse call syste
Page 63 and 64:
8.5 Group bus and ward bus (code: c
Page 65 and 66:
8. Laying cables 4. Only now cut of
Page 67 and 68:
8.5.4 Ward bus Group bus GE Termina
Page 69 and 70:
9. Switching on the power supply Pr
Page 71 and 72:
10. Configuring the nurse call syst
Page 73 and 74: CONCENTO PLUS - Technical Manual, 1
Page 79 and 80: 11.2.1.1 Checking function from WCs
Page 83 and 84: 12.1 Room terminals 19 0700 20 Term
Page 85 and 86: Terminal SD6 P, order no. 19 0700 2
Page 87 and 88: Terminal SD6 P, order no. 19 0700 2
Page 89 and 90: Tunstall GmbH, Orkotten 66, 48291 T
Page 93 and 94: Display module, order no. 19 0700 8
Page 95 and 96: Display module, order no. 19 0700 8
Page 97 and 98: Call/presence combination bus (RAB)
Page 99 and 100: Tunstall GmbH, Orkotten 66, D-48291
Page 103 and 104: Corridor display, order no. 19 0781
Page 105 and 106: Corridor display, double-sided, ord
Page 117 and 118: 12. Product leaflets 12.4 Call swit
Page 119 and 120: Call switch with connection socket,
Page 123: Tunstall GmbH, Orkotten 66, 48291 T
Page 135 and 136: 12. Product leaflets 12.6 Power sup
Page 137 and 138: Power supply unit UPS, Order No. 77
Page 143 and 144: Power supply unit, Order No. 77 340
Page 145 and 146: 3. Commissioning Power supply unit,
Page 147 and 148: Power supply unit UPS 60, Order No.
Page 153 and 154: Battery Set for UPS 60, Order No. 7
Page 155 and 156: Battery Set for UPS 60, Order No. 7
Page 157 and 158: 13. Programming tables, checklist
Page 159 and 160: Programming table, terminal configu
Page 161 and 162: Programming table, group coupling P
Page 164: Find all you want to know about the
show all

Technical Manual - Tunstall GmbH

Create successful ePaper yourself

Delete template?

Save as template?