Technical Manual - Tunstall GmbH

More documents

Recommendations

Info

Battery Set for UPS 60, Order No. 77 3450 00 The battery set for UPS 60 are rechargeable batteries (= accumulators) that build an uninterrupted power supply (UPS) in combination with the power supply unit UPS 60, order no. 77 3400 10. If the mains input voltage fails or when it drops to less than 90 VAC, the two lead-gel batteries will continue to supply the users connected to the power supply unit UPS 60 without any interruption. Safety instructions 1. Mounting • The battery set may only be used together with the power supply unit UPS 60, order no. 77 3400 10. The safety instructions delivered with this power supply unit have to be observed as well. • The power supply unit UPS should only be installed and commissioned by qualified specialists. • Before effecting any work at or with the power supply unit UPS, it must be isolated from any input voltage and the battery fuse (located between the batteries) has to be removed. • Always watch for the safe isolation of AC and DC circuits! • Observe the general safety instructions for the handling of batteries! Sufficient ventilation must be provided to preclude the development of an explosive hydrogenair mixture! • If the battery set for UPS 60 will not be used for a longer time, first the batteries have to be fully charged. After that the batteries must be disconnected from the mains supply. This can be done by disconnecting the battery connection cable from the power supply unit UPS 60 (see chapter 2.). Alternatively the battery fuse can be removed. The battery set for UPS 60 is designed for wall mounting. Bore holes are prepared at the housing for fixing the unit at the wall – preferably under the power supply unit - using the enclosed mounting material. A dimensional drawing is shown on the next page. Before mounting, check the condition of the wall itself. The battery set for UPS 60 weighs approx. 25.2 kg. The unit must be mounted such that the venting ports are at the top and bottom. The selected location must ensure sufficient air circulation above and below the unit. Therefore, check for minimum distance of 50 mm to walls, ceiling and other equipment. The venting ports must not be covered up. Insufficient air circulation may lead to damage to the power supply unit. © Tunstall GmbH, Orkotten 66, 48291 Telgte, Germany, www.tunstall.de, 00 8802 82, Rev. 2.1 (05/2008) English - 1 Technical Manual Page 150
Battery Set for UPS 60, Order No. 77 3450 00 Dimensional drawing: 2. Connection The connection terminals are provided as cage srew/plug-in clamps. 1. Release 6 fastening screws for the cover and remove the cover to the front. Now, the terminal connection clamps are accessible. 2. Direct the connection cable through the cable duct into the power supply unit and connect to the appropriate terminal posts as designated in the power supply unit. CAUTION! Check for the correct connection, orientation and screwing. 3. Secure the connection cable against being pulled from the housing for example by fixing the installation cable with the screwed cable gland. 2.1 Battery test The power supply unit features an automatic battery load test. The battery load test is an effective instrument for checking the true battery state. A negative result, i.e. a warning message is issued, may be caused by one or more of the following: • Charge status too low. • Battery fuse has failed. • Battery not correctly connected. • Battery is defective. • Battery is too old, and must be replaced. English - 2 © Tunstall GmbH, Orkotten 66, 48291 Telgte, Germany, www.tunstall.de, 00 8802 82, Rev. 2.1 (05/2008) Technical Manual Page 151
Page 1 and 2:
CONCENTO PLUS Technical Manual COMM
Page 3 and 4:
CONCENTO PLUS - Technical Manual, 1
Page 5 and 6:
Page 7 and 8:
1.5 General safety regulations CONC
Page 9 and 10:
2. Prior knowledge required 2.1 Sys
Page 11 and 12:
Page 13 and 14:
2.4 ConLog PLUS Management Software
Page 15 and 16:
2.5.2 Group speech Group bus CONCEN
Page 17 and 18:
Page 19 and 20:
Per room Per bed In WC room Termina
Page 21 and 22:
Per room Per bed In WC room Display
Page 23 and 24:
3.3 Staff room c+k Per room CONCENT
Page 25 and 26:
3.4.2 Function room without speech
Page 27 and 28:
3.5.2 Ward bathroom without speech
Page 29 and 30:
Per room Display module or Call/pre
Page 31 and 32:
Per room Terminal SD6 P or Terminal
Page 33 and 34:
Per room Display module or Call/pre
Page 35 and 36:
Per apartment Per bed Terminal S4 B
Page 37 and 38:
4. Accessories required Accessories
Page 39 and 40:
5. Installation examples See below
Page 41 and 42:
5.2 Nurse call system with speech:
Page 43 and 44:
5.4 Assisted living g (equipotentia
Page 45 and 46:
5.5.2 1‐bed room with WC Ward bus
Page 47 and 48:
5.5.4 1-bed room with WC: Wiring in
Page 49 and 50:
6. Installation sequence Work step
Page 51 and 52:
7. Defining mounting positions 7.1
Page 53 and 54:
7. Defining mounting positions 7.3
Page 55 and 56:
7.3.3 Switches ÀÀ ÀÀÀÀÀ ÀÀ
Page 57 and 58:
Page 59 and 60:
8.3 Power supply cable (code: k) CO
Page 61 and 62:
8.3.1 Earthing the nurse call syste
Page 63 and 64:
8.5 Group bus and ward bus (code: c
Page 65 and 66:
8. Laying cables 4. Only now cut of
Page 67 and 68:
8.5.4 Ward bus Group bus GE Termina
Page 69 and 70:
9. Switching on the power supply Pr
Page 71 and 72:
10. Configuring the nurse call syst
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
11.2.1.1 Checking function from WCs
Page 81 and 82:
Page 83 and 84:
12.1 Room terminals 19 0700 20 Term
Page 85 and 86:
Terminal SD6 P, order no. 19 0700 2
Page 87 and 88:
Terminal SD6 P, order no. 19 0700 2
Page 89 and 90:
Tunstall GmbH, Orkotten 66, 48291 T
Page 91 and 92:
Tunstall GmbH, Orkotten 66, 48291 T
Page 93 and 94:
Display module, order no. 19 0700 8
Page 95 and 96:
Display module, order no. 19 0700 8
Page 97 and 98:
Call/presence combination bus (RAB)
Page 99 and 100:
Tunstall GmbH, Orkotten 66, D-48291
Page 101 and 102: Tunstall GmbH, Orkotten 66, D-48291
Page 103 and 104: Corridor display, order no. 19 0781
Page 105 and 106: Corridor display, double-sided, ord
Page 107 and 108: Tunstall GmbH, Orkotten 66, 48291 T
Page 117 and 118: 12. Product leaflets 12.4 Call swit
Page 119 and 120: Call switch with connection socket,
Page 135 and 136: 12. Product leaflets 12.6 Power sup
Page 137 and 138: Power supply unit UPS, Order No. 77
Page 143 and 144: Power supply unit, Order No. 77 340
Page 145 and 146: 3. Commissioning Power supply unit,
Page 147 and 148: Power supply unit UPS 60, Order No.
Page 149 and 150: Power supply unit UPS 60, Order No.
Page 151: Power supply unit UPS 60, Order No.
Page 155 and 156: Battery Set for UPS 60, Order No. 7
Page 157 and 158: 13. Programming tables, checklist
Page 159 and 160: Programming table, terminal configu
Page 161 and 162: Programming table, group coupling P
Page 164: Find all you want to know about the
show all

Technical Manual - Tunstall GmbH

Create successful ePaper yourself

Delete template?

Save as template?