You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Terminal SD6 P, order no. 19 0700 20<br />
Connect the connecting cable and set the DIP switches<br />
Note! There is no bridge between 1 and 2<br />
(GND) and no bridge between 3 and 4<br />
(+24V) in the connector. The bridges are on<br />
the printed circuit board.<br />
R6 = Door alarm<br />
R5 = Fire<br />
R4 = WC cancel button<br />
R7 = Door alarm<br />
Ward bus (data)<br />
Ward bus (speech)<br />
+24 V<br />
RD<br />
IA<br />
WH(YE)<br />
R6<br />
IB<br />
YE<br />
Legend:<br />
1 ) GND = Connection to Point 1 or 2 of the 4-pole connector,<br />
or Point 1 of the 10-pole connector<br />
2 ) Colour WA = WH. Only for Call & cancel switch only = WH(GN).<br />
3 ) Switching power per output: 100 mA at 24 V DC.<br />
00 8814 18, 10/12 (Rev. 2.0) 2<br />
<strong>Technical</strong> <strong>Manual</strong> Page 83<br />
+24 V<br />
ISA<br />
WH(GN)<br />
R5<br />
ISB<br />
GN<br />
BU<br />
GND<br />
+24 V<br />
ISC<br />
WH(BN)<br />
GND<br />
R4<br />
ISD<br />
BN<br />
BN<br />
+24 V<br />
+24 V<br />
AW<br />
WL<br />
RL<br />
GND<br />
10 9 8 7 6 5 4 3 2 1<br />
YE<br />
R3<br />
WH<br />
+24 V<br />
1 2 3 4<br />
Room lamp 3 )<br />
Power supply<br />
+24 V<br />
RD<br />
4-pole connector<br />
Max. wire cross section: 2.5 mm 2<br />
R2<br />
BK or BU<br />
+24 V<br />
R1<br />
1 2 3 4 5 6 7 8 9 10 11 12<br />
WH<br />
BK or BU GND 1 )<br />
BK or BU GND 1 )<br />
BK or BU GND 1 )<br />
Inputs<br />
A maximum of 4 monitored devices can be connected at each<br />
input.<br />
All inputs are configurable. For restrictions when installing in an<br />
existing Concento system, see the ”Configuring inputs” chapter.<br />
The factory setting is shown in Fig. D and E.<br />
The following parameters can be configured:<br />
- Call type<br />
- NC/NO contact<br />
- Static call (trigger pulse) / dynamic call (trigger duration)<br />
RD<br />
WH<br />
RD<br />
WH 2 )<br />
RD<br />
WH<br />
YE<br />
RD<br />
YE<br />
WH<br />
RD<br />
WH<br />
GND 1 )<br />
GND 1 )<br />
GND 1 )<br />
ON<br />
OFF<br />
BK or BU<br />
BK or BU<br />
12-pole connector<br />
BK or BU<br />
R1 = Call button Bed 1<br />
R2 = Call button Bed 2<br />
R3 = WC call button<br />
10-pole connector<br />
DIP switch<br />
ON: Terminal is the first or last bus<br />
user on the ward bus<br />
(= bus termination)<br />
OFF: Terminal is neither the first nor<br />
last bus user on the ward bus<br />
One wire<br />
Four wires<br />
Factory setting of the inputs<br />
Inp. Call type NC or NO<br />
contact<br />
Output<br />
Input<br />
Static or<br />
dynamic call<br />
R1 Bed 1<br />
NO contact Static call<br />
R2 Bed 2<br />
NO contact Static call<br />
R3 WC call<br />
NO contact Static call<br />
R4 WC cancel button NO contact Static call<br />
R5 Fire<br />
NO contact Dynamic call<br />
R6 Door alarm NO contact Static call<br />
R7 Door alarm NO contact Static call
Change language