Technical Manual - Tunstall GmbH

More documents

Recommendations

Info

7. Defining mounting positions 7.2 Mounting heights 50 Specified mounting heights in accordance with the German standard DIN VDE 0834-1:2000: Mounting height above the floor: Devices for operation (with and without indicator lamps) 700 - 1,500 mm Devices for operation with text displays 1500 - 1,700 mm Devices in installation units 1600 - 1,800 mm Signal lamps and large-text displays 1500 - 2,200 mm Distribution boxes 700 - 2,200 mm Pull cord switches or similar in shower cubicles 200 mm above the highest possible shower head posi‐ tion CONCENTO PLUS - Technical Manual, 11/12 (Rev. 3.0), 00 8814 14
7. Defining mounting positions 7.3 Recommendations for CONCENTO PLUS In the following pages you will find installation examples with practical recom‐ mendations for CONCENTO PLUS products. 7.3.1 Room terminals and other room controllers 120 mm 120 mm 120 mm 120 mm 170 mm 170 mm 1,600 mm 1,600 mm 1,600 mm Terminal CONCENTO PLUS - Technical Manual, 11/12 (Rev. 3.0), 00 8814 14 Order no.: 19 0700 20, 19 0700 40, 19 0700 70 Position in the room: Near the door. 2-gang back box required. Note: With 2-gang back sockets, a space of at least 120 mm upwards and downwards from the centre point of the box must be provided for the terminal. When a pull cord (order no. 10 1421 10) is installed, the pull handle must not be higher than 200 mm above the floor so that persons lying on the floor can reach the pull cord. Terminal in an apartment Order no.: 19 0700 70 In an assisted living apartment, the terminal should be in‐ stalled in a position that favours audible contact from where speech contact is possible throughout the apartment, for ex‐ ample in the living room. 2-gang back box required. Note: With 2-gang back boxes, a space of at least 120 mm upwards and downwards from the centre point of the box must be provided for the terminal. When a pull cord (order no. 10 1421 10) is installed, the pull handle must not be higher than 200 mm above the floor so that persons lying on the floor can reach the pull cord. Display module Order no.: 19 0700 80 Position in the room: Near the door. 1-gang back box required. 51
Page 1 and 2: CONCENTO PLUS Technical Manual COMM
Page 3 and 4: CONCENTO PLUS - Technical Manual, 1
Page 7 and 8: 1.5 General safety regulations CONC
Page 9 and 10: 2. Prior knowledge required 2.1 Sys
Page 13 and 14: 2.4 ConLog PLUS Management Software
Page 15 and 16: 2.5.2 Group speech Group bus CONCEN
Page 19 and 20: Per room Per bed In WC room Termina
Page 21 and 22: Per room Per bed In WC room Display
Page 23 and 24: 3.3 Staff room c+k Per room CONCENT
Page 25 and 26: 3.4.2 Function room without speech
Page 27 and 28: 3.5.2 Ward bathroom without speech
Page 29 and 30: Per room Display module or Call/pre
Page 31 and 32: Per room Terminal SD6 P or Terminal
Page 33 and 34: Per room Display module or Call/pre
Page 35 and 36: Per apartment Per bed Terminal S4 B
Page 37 and 38: 4. Accessories required Accessories
Page 39 and 40: 5. Installation examples See below
Page 41 and 42: 5.2 Nurse call system with speech:
Page 43 and 44: 5.4 Assisted living g (equipotentia
Page 45 and 46: 5.5.2 1‐bed room with WC Ward bus
Page 47 and 48: 5.5.4 1-bed room with WC: Wiring in
Page 49 and 50: 6. Installation sequence Work step
Page 51: 7. Defining mounting positions 7.1
Page 55 and 56: 7.3.3 Switches ÀÀ ÀÀÀÀÀ ÀÀ
Page 59 and 60: 8.3 Power supply cable (code: k) CO
Page 61 and 62: 8.3.1 Earthing the nurse call syste
Page 63 and 64: 8.5 Group bus and ward bus (code: c
Page 65 and 66: 8. Laying cables 4. Only now cut of
Page 67 and 68: 8.5.4 Ward bus Group bus GE Termina
Page 69 and 70: 9. Switching on the power supply Pr
Page 71 and 72: 10. Configuring the nurse call syst
Page 79 and 80: 11.2.1.1 Checking function from WCs
Page 83 and 84: 12.1 Room terminals 19 0700 20 Term
Page 85 and 86: Terminal SD6 P, order no. 19 0700 2
Page 87 and 88: Terminal SD6 P, order no. 19 0700 2
Page 89 and 90: Tunstall GmbH, Orkotten 66, 48291 T
Page 91 and 92: Tunstall GmbH, Orkotten 66, 48291 T
Page 93 and 94: Display module, order no. 19 0700 8
Page 95 and 96: Display module, order no. 19 0700 8
Page 97 and 98: Call/presence combination bus (RAB)
Page 99 and 100: Tunstall GmbH, Orkotten 66, D-48291
Page 101 and 102: Tunstall GmbH, Orkotten 66, D-48291
Page 103 and 104:
Corridor display, order no. 19 0781
Page 105 and 106:
Corridor display, double-sided, ord
Page 107 and 108:
Tunstall GmbH, Orkotten 66, 48291 T
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
12. Product leaflets 12.4 Call swit
Page 119 and 120:
Call switch with connection socket,
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Tunstall GmbH, Orkotten 66, D-48291
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
12. Product leaflets 12.6 Power sup
Page 137 and 138:
Power supply unit UPS, Order No. 77
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Power supply unit, Order No. 77 340
Page 145 and 146:
3. Commissioning Power supply unit,
Page 147 and 148:
Power supply unit UPS 60, Order No.
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Battery Set for UPS 60, Order No. 7
Page 155 and 156:
Battery Set for UPS 60, Order No. 7
Page 157 and 158:
13. Programming tables, checklist
Page 159 and 160:
Programming table, terminal configu
Page 161 and 162:
Programming table, group coupling P
Page 164:
Find all you want to know about the
show all

Technical Manual - Tunstall GmbH

Create successful ePaper yourself

Delete template?

Save as template?