Technical Manual - Tunstall GmbH

More documents

Recommendations

Info

Tunstall GmbH, Orkotten 66, D-48291 Telgte, www.tunstall.de Display module, order no. 19 0700 80 Module for nurse call systems CONCENTO PLUS type for use by staff including a green presence button and a red call button as well as a display and a buzzer for displaying forwarded calls. The display module controls all room functions according to the Ger‐ man standard DIN VDE 0834. It is possible to use the display module in an existing nurse call system „Concento“ type, if it is connected to a ward bus with a group electronic only of order no.10 0700 10. A 4-pole and a 12-pole connector are included with delivery. Dimensions (HxWxD): 102 x 100 x 29 mm Weight: approx. 180 g Standby current consumption: approx. 10 mA at 24 V DC Note! The complete installation of the system is described in the Technical Manual. Caution! Electrostatic sensitive components The printed circuit board within the display module includes electro static sensitive components. Therefore avoid touching. Mounting Wall mounting on a one gang back box. 1. Strip the connection cables to the appropriate length. Remove the cable shield and ground wire up to the cable sheath. 2. Unplug the connectors from the printed circuit board. 3. Attach the wires according to Fig. E to both connectors. 4. Release the fixing screw 2 on the bottom of the display module 1. 5. Unlink the mounting frame 4 from the display module 1, by reaching into the mounting frame 4 and levering off the mounting frame. 6. Set the three DIP switches 8 (see Fig. A) on the rear side of the display module according to Fig. E. 7. Route both wired connectors through the opening of the mounting frame 4. 8. Fix the mounting frame 4 with the back box screws 3 to the back box 5. 9. Plug both wired connectors to the connection field 7. 10.Grip the display module at the level of the buttons and lever it off from the wall 11. While holding the display module 1 at the level of the buttons hinge it into the mounting frame and press it down until it lies flat on the mounting frame, see Fig. C. 12.Fix the fixing screw 2 in the hole at the bottom of the display module 1. Dismantling 1. Release the fixing screw 2 on the bottom of the display module 1. 2. With one hand hold the display module at the level of the buttons and lever it from the wall, see Fig. D. 3. Unplug both connectors from the rear side of the display module 1. 4. Release the back box screws 3 and remove the mounting frame 4 from the back box 5. 00 8814 02, 10/12 (Rev. 4.0) 1 Technical Manual Page 90 1 front view 1 rear view (without mounting frame) 1 Display module 2 Fixing screw 3* Back box screws 4 Mounting frame 5* Back box, 1-gang 7 Connection field 8 DIP switches * Not included with delivery. 1 2 1 3 1 3 2 2 7 4 4 4 8 5
Display module, order no. 19 0700 80 Connecting the wires to the connectors and setting the DIP switches RL Room lamp 7 ) AW WL Ward bus (data) GND IA WH(YE) R3 IB YE R4 00 8814 02, 10/12 (Rev. 4.0) 2 Technical Manual Page 91 +24 V GND BU +24 V +24V BN R1 R2 WR 12 11 10 9 8 7 6 5 4 3 2 1 4 IA R3 = Call button bed 3 1 ) 3 ) R4 = Door alarm 1 ) 2 ) 3 ) IB 3 2 1 GND R1 = Call button bed 1 1 ) 3 ) +24 V Display module is first or last ward bus user (= bus termination). WC calls can be cancelled with the WC cancel button or the presence button. R2 = Call button bed 2 1 ) 3 ) WC call button 3 ) WC cancel button 3 ) WA Legend: 1 ) In CONCENTO PLUS systems the call type and contact type can be changed, refer to chapter “Configuration“ on page 3. 2 ) In Concento systems R4 = Room call. 3 ) Maximum 4 monitored devices per input. 4 ) RL colour = YE. For room lamp only = RD. 5 ) WL colour = YE. For room lamp only = WH. 6 ) WA colour = WH. For room lamp only = WH(GN). 7 ) Switching power per output: 100 mA at 24 V DC. One wire Oour wires Output Input 4-pole connector Max. wire cross-section: 2.5 mm 2 Power supply (input) Note! All inputs are pre-programmed as NO contacts. 12-pole connector ON OFF 1 2 Display module is neither first nor last ward bus user. WC calls can be cancelled only with the WC cancel button. 3 DIP switches 1, 2, 3 DIP Switch ON OFF Factory Setting 1 2 3 YE 4 ) YE YE 5 ) BK or BU WH WH RD RD WH Not all ward bus users are CONCENTO PLUS type. One or more ward bus users are Concento type, order no.: - Group electronic: 10 0700 10 - Terminals: 10 0700 x0 - Display module: 10 0700 8x - RAB: 10 0701 x0 WH WH WH 6 ) All ward bus users are CONCENTO PLUS type, order no.: - Group electronic: 19 0700 10 - Terminals: 19 0700 x0 - Display module: 19 0700 80 - RAB: 19 0701 00 OFF OFF OFF Tunstall GmbH, Orkotten 66, D-48291 Telgte, www.tunstall.de
Page 1 and 2:
CONCENTO PLUS Technical Manual COMM
Page 3 and 4:
CONCENTO PLUS - Technical Manual, 1
Page 5 and 6:
Page 7 and 8:
1.5 General safety regulations CONC
Page 9 and 10:
2. Prior knowledge required 2.1 Sys
Page 11 and 12:
Page 13 and 14:
2.4 ConLog PLUS Management Software
Page 15 and 16:
2.5.2 Group speech Group bus CONCEN
Page 17 and 18:
Page 19 and 20:
Per room Per bed In WC room Termina
Page 21 and 22:
Per room Per bed In WC room Display
Page 23 and 24:
3.3 Staff room c+k Per room CONCENT
Page 25 and 26:
3.4.2 Function room without speech
Page 27 and 28:
3.5.2 Ward bathroom without speech
Page 29 and 30:
Per room Display module or Call/pre
Page 31 and 32:
Per room Terminal SD6 P or Terminal
Page 33 and 34:
Per room Display module or Call/pre
Page 35 and 36:
Per apartment Per bed Terminal S4 B
Page 37 and 38:
4. Accessories required Accessories
Page 39 and 40:
5. Installation examples See below
Page 41 and 42: 5.2 Nurse call system with speech:
Page 43 and 44: 5.4 Assisted living g (equipotentia
Page 45 and 46: 5.5.2 1‐bed room with WC Ward bus
Page 47 and 48: 5.5.4 1-bed room with WC: Wiring in
Page 49 and 50: 6. Installation sequence Work step
Page 51 and 52: 7. Defining mounting positions 7.1
Page 53 and 54: 7. Defining mounting positions 7.3
Page 55 and 56: 7.3.3 Switches ÀÀ ÀÀÀÀÀ ÀÀ
Page 57 and 58: CONCENTO PLUS - Technical Manual, 1
Page 59 and 60: 8.3 Power supply cable (code: k) CO
Page 61 and 62: 8.3.1 Earthing the nurse call syste
Page 63 and 64: 8.5 Group bus and ward bus (code: c
Page 65 and 66: 8. Laying cables 4. Only now cut of
Page 67 and 68: 8.5.4 Ward bus Group bus GE Termina
Page 69 and 70: 9. Switching on the power supply Pr
Page 71 and 72: 10. Configuring the nurse call syst
Page 79 and 80: 11.2.1.1 Checking function from WCs
Page 83 and 84: 12.1 Room terminals 19 0700 20 Term
Page 85 and 86: Terminal SD6 P, order no. 19 0700 2
Page 87 and 88: Terminal SD6 P, order no. 19 0700 2
Page 89 and 90: Tunstall GmbH, Orkotten 66, 48291 T
Page 91: Tunstall GmbH, Orkotten 66, 48291 T
Page 95 and 96: Display module, order no. 19 0700 8
Page 97 and 98: Call/presence combination bus (RAB)
Page 99 and 100: Tunstall GmbH, Orkotten 66, D-48291
Page 103 and 104: Corridor display, order no. 19 0781
Page 105 and 106: Corridor display, double-sided, ord
Page 117 and 118: 12. Product leaflets 12.4 Call swit
Page 119 and 120: Call switch with connection socket,
Page 135 and 136: 12. Product leaflets 12.6 Power sup
Page 137 and 138: Power supply unit UPS, Order No. 77
Page 143 and 144:
Power supply unit, Order No. 77 340
Page 145 and 146:
3. Commissioning Power supply unit,
Page 147 and 148:
Power supply unit UPS 60, Order No.
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Battery Set for UPS 60, Order No. 7
Page 155 and 156:
Battery Set for UPS 60, Order No. 7
Page 157 and 158:
13. Programming tables, checklist
Page 159 and 160:
Programming table, terminal configu
Page 161 and 162:
Programming table, group coupling P
Page 164:
Find all you want to know about the
show all

Technical Manual - Tunstall GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?