Operator's Manual – AutoCycle iC - Ferguson Beauregard

Recommendations

Info

ACiC Operator’s Manual Revision 4 Page 54 of 95 There are three types of SMS commands that may be sent to the ACiC: Read-Only Commands: Read-Only commands are used to retrieve data that typically cannot be altered by the user. This type of information includes data points such as pressures, temperatures, and plunger run times among others. Retrieving information using a Read-Only command can be done by sending the Shortcut or Hotkey to the controller with no parameters. Step 1: User initiates read command SYS Step 2: ACIC generates the response Joe’s Mega Well BATT: 13.08V SOLAR: -1.0mA FW VER: 1.1.24.0 PLG CTS: 21 Read-Write Commands: Read-Write commands are used either to retrieve current values or change items in the ACiC. This type of command is used for changing settings such as control times or pressure overrides or retrieving the current setting. Retrieving a setting is done by sending the hotkey or shortcut with a preceding ‘?’ character. Altering a setting using Read-Write commands can be done by sending the Shortcut or Hotkey followed by a space character and a parameter. Step 1: User Initiates SMS ?03 (request current ON time setting) Step 2: ACIC generates the response Joe’s Mega Well 03 00:05:10 Step 1: User Initiates SMS 03 001010 (change ON time to 10 minutes and 10 seconds) Step 2: ACIC generates the response Joe’s Mega Well OLD 03 00:05:10 NEW 03 00:10:10 Write-Only Commands: Write-Only commands are used to explicitly modify the current behavior of the controller. These commands affect behavior such as enabling or disabling functionality, or closing valves. Write-Only commands are used without parameters by sending the Shortcut or Hotkey and will return only a confirmation once action is taken. Step 1: User Initiates SMS SHUTIN Step 2: remote ACIC generates the response Joe’s Mega Well SHUTIN Confirmed 2913 Specialty Drive • P.O. Box 130158 • Tyler, TX 75713-0158 • Phone: 903-561-4851 • Fax: 903-561-6567
ACiC Operator’s Manual Revision 4 Page 55 of 95 6.4 Parameters There are several parameter types to be used with Read-Write commands. The parameter associated with a Read-Write command will start as the first non-space character on a given line, not including the security code. Responses to Read-Write commands with required parameter value changes will also contain the well name and OLD and NEW values. Time: Time parameters are formatted hoursminutesseconds with no delimiters between each value and no leading zeroes. For example, 2000 represents 20 minutes 00 seconds while 100000 translates to 10 hours, 00 minutes, 00 seconds. Confirmation messages containing times will use a colon (:). Integers: The ACIC supports up to 6 digit integers or whole numbers (123456). Floating Point: The ACIC supports up to 4 digits of precision floating point values (123456.0987) 6.5 The Help Command The help command is a unique read-only command that accepts any other command as a parameter. When used, the ACiC will return a short description of the parameter command and its usage. Two question marks preceding any command type will initiate the help command. A maximum of two help commands can be sent per SMS message. No other command may be sent in the same SMS message as a help command. Step 1: User Initiates SMS ?? SHUTIN ?? 03 Step 2: ACIC generates the response Joe’s Mega Well SHUTIN- Closes all valves, Manual Mode 03 [hr:min:sec]-Current on time 6.6 Unrecognized Commands Responses to unrecognized numerical and/or word based commands will be as follows: Step 1: User Initiates SMS SYSS Step 2: remote ACiC generates the response Joe’s Mega Well INV CMD: SYSS 2913 Specialty Drive • P.O. Box 130158 • Tyler, TX 75713-0158 • Phone: 903-561-4851 • Fax: 903-561-6567
Page 1 and 2:
Operator’s Manual Revision: 4 Rev
Page 3 and 4: ACiC Operator’s Manual Revision 4
Page 53: ACiC Operator’s Manual Revision 4
Page 73 and 74: 1. 2. 3. 4. 5. 6. 7. 8. 9. ACiC Ope
Page 77 and 78: 1. 2. 3. 4. 5. 6. ACiC Operator’s
Page 85 and 86: 1. 2. 3. 4. 5. 6. 7. ACiC Operator
Page 95: 8. 9. ACiC Operator’s Manual Revi
show all

Operator's Manual – AutoCycle iC - Ferguson Beauregard

Create successful ePaper yourself

Delete template?

Save as template?