Operator's Manual – AutoCycle iC - Ferguson Beauregard

Recommendations

Info

ACiC Operator’s Manual Revision 4 Page 62 of 95 7.1 Ferguson Beauregard Ni EFM3000 To configure the EFM3000 you will need the EFMaintainer application which can be downloaded from the Ferguson Beauregard website at http://www.fergusonbeauregard.com from the Software downloads section. P6 (LCD) ANLG 1 RED BLK GND ANLG 2 TB6 GND ANLG 3 ANLG 4 GND TB5 TB3 CTS RXD MPU RUN Green Red TXD SLP TB4 Black GND RTS To ACiC B1 DI 1/ACC EFM3000 Rev F Board P2 DI 2 RXD TXD GND 2913 Specialty Drive • P.O. Box 130158 • Tyler, TX 75713-0158 • Phone: 903-561-4851 • Fax: 903-561-6567 CTRL O/P GND To ACiC A B TB7 Green Red Black TB2 Network Port Console Port Figure 7.2: Ni EFM3000 Wiring Diagram Network (TB4) Console (TB2) EFM3000 Function 30606VM Wire Color PC 232CONV Pin 2 Pin 1 TXD Red Pin 2 Pin 3 Pin 2 RXD Green Pin 1 Pin 5 Pin 3 GND Black Pin 5 Table 7.1: Ni EFM3000 Wiring Table CHRG Power Connector Radio - Radio + Batt. - Batt. + Solar - Solar + TB1
ACiC Operator’s Manual Revision 4 Page 63 of 95 7.1.1 ACiC Configuration for Ni EFM3000 1. Open the ACiC in iCConnect and choose the Input Config tab 2. Set the Differential pressure analog channel, Line Pressure analog channel, and Line Temperature analog channel to FCU. 3. Click the Save button. 4. Choose System tab. 5. Set the port setup sections according to Table 7.2. 6. Click the Save button. 7. Choose the FCU tab. 8. Set the appropriate MODBUS address of the EFM3000. 9. Set all the other FCU parameters according to Table 7.3. 10. Click the Save button. Setting Value Port Setup (Serial or TTL) Baud Rate 19200 Parity None Flow Control No flow control Stop Bits 1 Stop bit Data Bits 8 Data bits Port Device External Device Port Protocol Flow computer (FCU) Table 7.2: iCConnect System Tab - EFM3000 Setting Value Capture window Previous volume capture window end 60 Previous volume capture window start 0 FCU Communications FCU’s MODBUS mode False FCU’s slave mode True Flow computer present True MODBUS address 1 Prefix byte 0 Prefix byte count 0 Suffix byte 0 Suffix byte count 0 FCU Data Format Byte order DCBA Data type Single precision float Flow computer type Fisher ROC Flow rate definition MCF per day Units False FCU Registers Current volume address 7605 DP address 7639 Flow address 7603 LT address 7641 Previous volume address 7607 SP address 7640 Totalflow base group number 0 FCU Scan Response timeout 7 Scan interval 1 Table 7.3: iCConnect FCU Tab – EFM3000 2913 Specialty Drive • P.O. Box 130158 • Tyler, TX 75713-0158 • Phone: 903-561-4851 • Fax: 903-561-6567
Page 1 and 2:
Operator’s Manual Revision: 4 Rev
Page 3 and 4:
ACiC Operator’s Manual Revision 4
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12: ACiC Operator’s Manual Revision 4
Page 61: ACiC Operator’s Manual Revision 4
Page 73 and 74: 1. 2. 3. 4. 5. 6. 7. 8. 9. ACiC Ope
Page 77 and 78: 1. 2. 3. 4. 5. 6. ACiC Operator’s
Page 85 and 86: 1. 2. 3. 4. 5. 6. 7. ACiC Operator
Page 95: 8. 9. ACiC Operator’s Manual Revi
show all

Operator's Manual – AutoCycle iC - Ferguson Beauregard

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?